|
Size: 2743
Comment:
|
Size: 1963
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 8: | Line 8: |
| * We characterized the remachined LBB blades, chose three and installed them in the LBB blade units in the PI. * We removed all sticky labels from the PI and cleaned the affected areas (and as much as possible of the rest of the surface) with ethanol. * We rearranged the arc weights on the PI to make space for the magic wand and installed the magic wand. * We rearranged the magnets on the SF damper ring to suit three Cu segments (instead of two as in the test hang). * We put proper vacuum-compatible tubing around all the stepper motor connections on the top of the PI (replacing cling wrap). * We craned out the SF temporarily and retrieved the lost PEEK cable clamp collet from the BF. * We closed the BF, craned the SF back in, and hooked the BF/..., this time with the hex cable clamp. * We routed cables from the BF via the hex cable clamp to the SF level. * We adjusted the BF trim mass for pitch, roll and vertical, and got the IRM hanging symmetrically around the IM. * We adjusted all the IRM OSEMs laterally and in/out. * We calibrated the SF LVDT and tested the SF FR stepper. * We suspended the SF/... section and weighed it but found the old 7-mm maraging rod adapter did not hold it at the center, so we had to lift it with slings and could not accurately trim it for pitch/roll. * Therefore we brought forward the craning in of the PI with the SF damper ring hanging from it. * We suspended the SF successfully from the PI and unlocked the F0 keystone to check the mass budget. We needed about 1.5 kg extra, which is about right considering the hex cable clamp and cables. * However we had to leave out the F0-SF hex cable clamp because of a bad thread on the inside of the cap. Hirata-san will make a new cap by enlarging the 7-mm hole in an old cap to 8 mm. |
* We put lock nuts on the F0 FR and calibrated the F0 LVDT against FR position and keystone height. * Enzo traced the issue with the geophones to a specific cable. * We measured the BF and F0 GAS resonant frequencies. * We adjusted the spacing of the SR damper. * We double-checked the BS pitch with the OL. * We debugged the PI yaw mechanism. We managed to get the return spring properly adjusted, but the stepper motor tends to jam because of the strange design. * '''We prepared the suspension for lifting and craned it into the tank.''' * Hirata-san fixed an issue with one of the nailheads on the LBB intermediate ring support rods not properly seating, by removing the rod and reinstalling it upside down (with the problem nailhead in a less critical position). * Enzo and team moved all the in-air cables from the assembly frame to the tank. * Fabian and Ohishi-san unlocked the bottom section of the suspension and got it hanging freely. ==== Plan for week of 9/25 ==== Mark, Fabian, Enzo (Mon, Tue), Ohishi-san (Tue, Fri), Hirata-san, Yoshioka-kun (Tue, Wed, Fri), Kozu-kun * Finish moving in-air cabling and feedthroughs and reconnect in-vacuum cables (through Cu O-rings). * Unlock rest of suspension and readjust. * Debug electronics. * Unclamp LBB ring "sandwich" so LBB Cu ring is suspended on upper rods. * Install LBB lower rods and hook LBB. * Adjust LBB damper Cu-magnet gap. * Measure required ballast for LBB. * Remove First Contact, try OL. * Prepare for SR2 work. |
| Line 24: | Line 31: |
| ==== Plan for week of 9/13 ==== Mark (except Wed), Fabian (except Mon, Tue), Enzo, Ohishi-san (except Mon-Wed), Hirata-san, Yoshioka-kun (Tue, Wed, Fri), Kozu-kun * Reinstall F0-SF rod, this time with hex cable clamp. * Route cables. * Adjust SF trim mass, adjust tilt and vertical. * Adjust SF damper gap. * Cable and test IP LVDTs. * Cable and test F0 LVDT. * Cable and test PI steppers. * Cable and test geophones. * ==== Plan for week of 9/19 ==== No work Mon 9/18 (敬老の日)<BR> Mark, Fabian, Enzo, Ohishi-san, Hirata-san, Yoshioka-kun (Tue, Wed, Fri), Kozu-kun * Install LBB damper rings. * Install suspension. |
==== Plan for week of 10/2 ==== Kamioka: Mark, Enzo, Fabian, Ohishi-san. * TFs etc. Mitaka: Hirata-san? * SF design/purchasing. |
| Line 43: | Line 39: |
| Enzo: 9/27-29 |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Past week report
At Kamioka (Mark, Ohishi-san, Fabian, Enzo, Hirata-san, Yoshioka-kun, Kozu-kun):
- We put lock nuts on the F0 FR and calibrated the F0 LVDT against FR position and keystone height.
- Enzo traced the issue with the geophones to a specific cable.
- We measured the BF and F0 GAS resonant frequencies.
- We adjusted the spacing of the SR damper.
- We double-checked the BS pitch with the OL.
- We debugged the PI yaw mechanism. We managed to get the return spring properly adjusted, but the stepper motor tends to jam because of the strange design.
We prepared the suspension for lifting and craned it into the tank.
- Hirata-san fixed an issue with one of the nailheads on the LBB intermediate ring support rods not properly seating, by removing the rod and reinstalling it upside down (with the problem nailhead in a less critical position).
- Enzo and team moved all the in-air cables from the assembly frame to the tank.
- Fabian and Ohishi-san unlocked the bottom section of the suspension and got it hanging freely.
Plan for week of 9/25
Mark, Fabian, Enzo (Mon, Tue), Ohishi-san (Tue, Fri), Hirata-san, Yoshioka-kun (Tue, Wed, Fri), Kozu-kun
- Finish moving in-air cabling and feedthroughs and reconnect in-vacuum cables (through Cu O-rings).
- Unlock rest of suspension and readjust.
- Debug electronics.
- Unclamp LBB ring "sandwich" so LBB Cu ring is suspended on upper rods.
- Install LBB lower rods and hook LBB.
- Adjust LBB damper Cu-magnet gap.
- Measure required ballast for LBB.
- Remove First Contact, try OL.
- Prepare for SR2 work.
Plan for week of 10/2
Kamioka: Mark, Enzo, Fabian, Ohishi-san.
- TFs etc.
Mitaka: Hirata-san?
- SF design/purchasing.
Vacation Info
Mark: 10/16-24 Enzo: 9/27-29