Diff for "KAGRA/Commissioning/Phase1/Operation/ShiftManual"

Differences between revisions 2 and 3

Describe KAGRA/Commissioning/Phase1/Operation/ShiftManual here. TEST

pic

pics

Look at the monitor here. If "ON", it is in OPERATION mode. If "OFF", it is not; something is strange

screen shots

screen shots

Check the state of LSC_MICH. First check if the request state of LSC_MICH is OPERATION. If it is not, request OPERATION.

Screen shot

If the state is READY, ENGAGE_SERVO, ENGAGE_BOOST, MICH_LOCKED, CALIBRATION_INJECTION, or ACTUATORCAL_INJECTION, the interferometer is now on the way to be OPERATION state. It will be ready soon. If it will not enter OPERATION state in a few minute, something is wrong. Call interferometer experts.
- If it is in DOWN state, go to 3.
Check the status of IMC_LOCKED, VIS_BS, VIS_PR2, VIS_PR3. (Note that VIS_PRM is not used for now, so just ignore it)

**aaa

you have to take the logbook to report the incident during the observation shift (see IFO Operational Manual)
you have to check the check list to avoid mistake during the observation shift (Check List)

ここから先は観測シフトの仕事を簡単にまとめたものです。まだ暫定的なメモのような状態なので、適宜アップデートして下さい。ここは分かりやすさのために日本語で書きます。余裕のある方は英語版も作って下さい。

[General]

[DGS]

sitemap→CDS→DAQが全部緑になっているかどうかを確認。緑じゃなければその項目のボタンを押し、statusが0×0になっているか確認。なっていなれけば宮川さんか苔山さんに連絡。

[MIF]

sitemap→guardian→MICH_LOCKとIMC_LOCKを確認。PSLは３月中は触らない。(IMCがロックしていればIMC_MCI_TRANS_OUTPUTは0.35くらい)

[VIS]

[DMG]

DMG Check-Sheetを２時間おきに書く。コントロールルーム隣のサーバールームのPCを見て、Check-SheetのIn case of normalを満たしているか確認。Is the log outputs normal?は、PC画面に赤か黄のメッセージが出てこなければOK。

[klog]

Abbreviation / Acronym	Meaning / Explanation
BS	Beam Splitter
CDS
DAQ	Data Acquisition
DAS	Data Analysis
DC	Direct Current
DET/Detchar	Detector Characterization
DGS	Digital System
DMG	Data Management
EPICS	Experimental Physics and Industrial Control System
EX/ETMX	X Arm End Test Mass
EY/ETMY	Y Arm End Test Mass
FCL	Facility
GAS	Geometric Anti-Spring
GIF	Geophysics Interferometer
Guardian	Automation system for interferometers
IFO	Interferometer Optics
IMC	Input Mode Cleaner
LSC	Length Sensing and Control, especially for MIF
MCi/e/o	Name of three mirrors of IMC; Input, End, and Output mirrors
Medm	GUI for dealing with EPICS
MI	Michealson Interferometer
MIF	Main Interferometer
OpLev	Optical Lever; measures angle of a mirror
OSEM	Optical Sensor and ElectroMagnet
PMC	Pre-Mode Cleaner
PR3	Type Bp’ SAS. works as the last steering mirror for MI
PSL	Pre-Stabilized Laser
SAS	Seismic Attenuation System
TM	Test Mass
VAC	Vacuum
VIS	Vibration Isolation System

KAGRA/Commissioning/Phase1/Operation/ShiftManual (last edited 2018-04-28 19:04:13 by YutaroEnomoto)

-  ⇤ ← Revision 2 as of 2018-04-28 15:29:37 → 
  Size: 3721
  Editor: YutaroEnomoto
  Comment:
+   ← Revision 3 as of 2018-04-28 15:51:27 → ⇥
  Size: 4018
  Editor: YutaroEnomoto
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 5:
+=== How to use Guardian ===
pics
-Line 15:
+Line 20:
-.  Check the state of LSC_MICH. If it is in READY, ENGAGE_SERVO, ENGAGE_BOOST, MICH_LOCKED, CALIBRATION_INJECTION, or ACTUATORCAL_INJECTION, the interferometer is now on the way to be OPERATION state. It will be ready soon. If it will not enter OPERATION state in a few minute, something is wrong. Call interferometer experts.
+.  Check the state of LSC_MICH. First check if the request state of LSC_MICH is OPERATION. If it is not, request OPERATION.
-Line 17:
+Line 22:
-screen shots
+Screen shot
-Line 19:
+Line 24:
-.  Check the
+. If the state is READY, ENGAGE_SERVO, ENGAGE_BOOST, MICH_LOCKED, CALIBRATION_INJECTION, or ACTUATORCAL_INJECTION, the interferometer is now on the way to be OPERATION state. It will be ready soon. If it will not enter OPERATION state in a few minute, something is wrong. Call interferometer experts.
    If it is in DOWN state, go to 3.

 3. Check the status of IMC_LOCKED, VIS_BS, VIS_PR2, VIS_PR3. (Note that VIS_PRM is not used for now, so just ignore it)
 
**aaa