Diff for "KAGRA/Commissioning/Phase1/Operation/ShiftManual"

Differences between revisions 42 and 53 (spanning 11 versions)

Contents

Control Room Overview

pic

How to use Guardian

Accessing to the guardian screen

In the sitemap, you can click on the link for the guardian overview screen.

It pops up the following screen,

Knowing the current state and requested state

How to request a state

Click on the gray bar in the middle.

Then, choose the desired state.

How to know the status of the interferometer

Look at one of the TV monitor in the control room. If "ON", it is in OPERATION mode.

If "OFF", check the guardian overview screen

Check the state of LSC_MICH. First check if the request state of LSC_MICH is OPERATION. If it is not, request OPERATION.
If the state is READY, ENGAGE_SERVO, ENGAGE_BOOST, MICH_LOCKED, CALIBRATION_INJECTION, or ACTUATORCAL_INJECTION, the interferometer is now on the way to be OPERATION state. It will be ready soon.
$/!\$ If it does not enter OPERATION state in a few mins. Call the interferometer experts.

Check the status of IMC_LOCK, VIS_BS, VIS_PR2, VIS_PR3. (Note that VIS_PRM is not used for now, so just ignore it)
For IMC_LOCK, every thing should be green and IMC should be back automatically.

For example, this is how the IMC_LOCK guardian should normally look like.

$/!\$ If it does not come back in ~ 10 mins, call interferometer/IOO experts.
For VIS_PR2 and VIS_BS, the state should be ALIGNED. If inot, a notification "please reset Watch Dog!" will show up, and the state is in TRIPPED. In that case, go to the next section to know how to reset Watch Dog.
For VIS_PR3, the state should be DAMPED. If it is not, a notification "please reset Watch Dog!" will show up, and the state is in TRIPPED. In that case, go to the next section to know how to reset Watch Dog.

How to reset Watch Dogs

Request LSC_MICH to be READY by Guardian.
Open Sitemap (from Terminal, type "mk" and press return).
Click VIS
Click the suspension of which you want to reset Watch Dog
Go to PRs case or BS case

PRs case

Request SAFE by Guardian
Open "DETAILS" at bottom right,
and you will find PRs overview screen
Click WATCHDOG
If something is red, press here to reset.
Click DACKILL (see the picture above, PRs overview sceen)
If it is not green, press reset.
Click Coil Driver WD (picture above, PRs overview sceen)
Check if everything is green. If there are red signs, push corresponding WD Pulse ON button and then OFF button
Request DAMPED. For PR2, ~ 10 seconds after the state becomes DAMPED, request ALIENED.
~ 10 seconds after the suspension gets in a nominal state, request LSC_MICH to be OPERATION.

BS case

Request SAFE by Guardian
Open "Payload" at bottom center,
- and you will find BS payload overview screen
Click WATCHDOG
If something is red, press here to reset.
Click DACKILL (see the picture above for BS overview screen)
If it is not green, press reset.
Click Coil Driver WD (see the picture above for BS overview screen)
Check if everything is green. If there are red signs, push corresponding WD Pulse ON button and then OFF button
Request DAMPED. For PR2, ~ 10 seconds after the state becomes DAMPED, request ALIENED.
~ 10 seconds after the suspension gets in a nominal state, request LSC_MICH to be OPERATION.

-  ⇤ ← Revision 42 as of 2018-04-28 18:05:16 → 
  Size: 7012
  Editor: YutaroEnomoto
  Comment:
+   ← Revision 53 as of 2018-04-28 18:39:01 → ⇥
  Size: 4739
  Editor: YutaroEnomoto
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 47:
-screenshot
+ {{attachment:VISALL.png||width="407"}}<<BR>>

 4. Go to PRs case or BS case
-Line 50:
+Line 52:
 . Request SAFE by Guardian
-Line 52:
+Line 54:
-. Open "DETAILS" at bottom right
+. Open "DETAILS" at bottom right,
-Line 54:
+Line 56:
-. Click WATCHDOG here.
+ {{attachment:PRTOP.png||width="300"}}<<BR>>
 . and you will find PRs overview screen
-Line 56:
+Line 59:
-pic
+ {{attachment:PR.png||width="800"}}<<BR>>
 
 6. Click WATCHDOG
-Line 59:
+Line 64:
+ {{attachment:PRWD.png||width="400"}}<<BR>>
-Line 60:
+Line 66:
-. Click DACKILL here.

pic pic
+. Click DACKILL (see the picture above, PRs overview sceen)
-Line 65:
+Line 69:
+ {{attachment:DACKILL.png||width="200"}}<<BR>>
-Line 66:
+Line 71:
-. Click this button

pic
+. Click Coil Driver WD (picture above, PRs overview sceen)
-Line 72:
+Line 75:
-pic
+ {{attachment:PR_CDWD.png||width="800"}}<<BR>>
-Line 74:
+Line 77:
 . Request DAMPED. For PR2, ~ 10 seconds after the state becomes DAMPED, request ALIENED.
-Line 76:
+Line 79:
 . ~ 10 seconds after the suspension gets in a nominal state, request LSC_MICH to be OPERATION.
-Line 79:
+Line 82:
 . Request SAFE by Guardian
-Line 81:
+Line 84:
-. Open "Payload" at bottom center
+. Open "Payload" at bottom center,
-Line 83:
+Line 86:
-. Click WATCHDOG here.
+ {{attachment:BSTOP.png||width="250"}}<<BR>>
  and you will find BS payload overview screen
-Line 85:
+Line 89:
-pic
+ {{attachment:BSpayload.png||width="800"}}<<BR>>
-Line 87:
+Line 91:
+. Click WATCHDOG
-Line 88:
+Line 93:
+ {{attachment:PRWD.png||width="400"}}<<BR>>
-Line 89:
+Line 95:
-. Click DACKILL here.

pic pic
+. Click DACKILL (see the picture above for BS overview screen)
-Line 94:
+Line 98:
+ {{attachment:DACKILL.png||width="200"}}<<BR>>
-Line 95:
+Line 100:
-. Click this button

pic
+. Click Coil Driver WD (see the picture above for BS overview screen)
-Line 101:
+Line 104:
-pic
+ {{attachment:PR_CDWD.png||width="800"}}<<BR>>
-Line 103:
+Line 106:
 . Request DAMPED. For PR2, ~ 10 seconds after the state becomes DAMPED, request ALIENED.
-Line 105:
+Line 108:
-. ~ 10 seconds after the suspension gets in a nominal state, request LSC_MICH to be OPERATION.

=== basic tasks ===
 * you have to take the logbook to report the incident during the observation shift (see [[http://gwwiki.icrr.u-tokyo.ac.jp/JGWwiki/KAGRA/Observation/iKAGRA/Manual/MIF|IFO Operational Manual]])

 * you have to check the check list to avoid mistake during the observation shift ([[http://gwdoc.icrr.u-tokyo.ac.jp/DocDB/0049/T1604975/005/CheckList_20160324.pdf|Check List]])

ここから先は観測シフトの仕事を簡単にまとめたものです。まだ暫定的なメモのような状態なので、適宜アップデートして下さい。ここは分かりやすさのために日本語で書きます。余裕のある方は英語版も作って下さい。

[General]

 * まずコントロールルームのPCのapplication→terminal→mk→sitemapが開かれる

[DGS]

 * sitemap→CDS→DAQが全部緑になっているかどうかを確認。緑じゃなければその項目のボタンを押し、statusが0×0になっているか確認。なっていなれけば宮川さんか苔山さんに連絡。

[MIF]

 * sitemap→guardian→MICH_LOCKとIMC_LOCKを確認。PSLは３月中は触らない。(IMCがロックしていればIMC_MCI_TRANS_OUTPUTは0.35くらい)

[VIS]

 * sitemap→VIS→PR3の画面右側のWATCHDOG、DACKILL IOPが緑かどうかを確認。

[DMG]

 * DMG Check-Sheetを２時間おきに書く。コントロールルーム隣のサーバールームのPCを見て、Check-SheetのIn case of normalを満たしているか確認。Is the log outputs normal?は、PC画面に赤か黄のメッセージが出てこなければOK。

[klog]

 * klogに干渉計の状況を簡単に報告。

=== useful information ===
 * terminology

||<#F0F0FF>Abbreviation / Acronym ||<#F0F0FF>Meaning / Explanation ||
||BS ||Beam Splitter ||
||CDS || ||
||DAQ ||Data Acquisition ||
||DAS ||Data Analysis ||
||DC ||Direct Current ||
||DET/Detchar ||Detector Characterization ||
||DGS ||Digital System ||
||DMG ||Data Management ||
||EPICS ||Experimental Physics and Industrial Control System ||
||EX/ETMX ||X Arm End Test Mass ||
||EY/ETMY ||Y Arm End Test Mass ||
||FCL ||Facility ||
||GAS ||Geometric Anti-Spring ||
||GIF ||Geophysics Interferometer ||
||Guardian ||Automation system for interferometers ||
||IFO ||Interferometer Optics ||
||IMC ||Input Mode Cleaner ||
||LSC ||Length Sensing and Control, especially for MIF ||
||MCi/e/o ||Name of three mirrors of IMC; Input, End, and Output mirrors ||
||Medm ||GUI for dealing with EPICS ||
||MI ||Michealson Interferometer ||
||MIF ||Main Interferometer ||
||OpLev ||Optical Lever; measures angle of a mirror ||
||OSEM ||Optical Sensor and ElectroMagnet ||
||PMC ||Pre-Mode Cleaner ||
||PR3 ||Type Bp’ SAS. works as the last steering mirror for MI ||
||PSL ||Pre-Stabilized Laser ||
||SAS ||Seismic Attenuation System ||
||TM ||Test Mass ||
||VAC ||Vacuum ||
||VIS ||Vibration Isolation System ||


 * how to search JGW document
+. ~ 10 seconds after the suspension gets in a nominal state, request LSC_MICH to be OPERATION.