• Diff for "KAGRA/Commissioning/Phase1/Operation/ShiftManual"

Control Room Overview

pic

How to use Guardian

Accessing to the guardian screen

• In the sitemap, you can click on the link for the guardian overview screen.

  
  It pops up the following screen,
  

Knowing the current state and requested state

How to request a state

• Click on the gray bar in the middle.
  
  Then, choose the desired state.
  

How to know the status of the interferometer

• Look at one of the TV monitor in the control room. If "ON", it is in OPERATION mode.

  
  If "OFF", check the guardian overview screen
  
  Check the state of LSC_MICH. First check if the request state of LSC_MICH is OPERATION. If it is not, request OPERATION.
  

• If the state is READY, ENGAGE_SERVO, ENGAGE_BOOST, MICH_LOCKED, CALIBRATION_INJECTION, or ACTUATORCAL_INJECTION, the interferometer is now on the way to be OPERATION state. It will be ready soon.
  If it does not enter OPERATION state in a few mins. Call the interferometer experts.
  

  Check the status of IMC_LOCK, VIS_BS, VIS_PR2, VIS_PR3. (Note that VIS_PRM is not used for now, so just ignore it)
  For IMC_LOCK, every thing should be green and IMC should be back automatically.
  

  
  For example, this is how the IMC_LOCK guardian should normally look like.
  
  If it does not come back in ~ 10 mins, call interferometer/IOO experts.
  For VIS_PR2 and VIS_BS, the state should be ALIGNED. If inot, a notification "please reset Watch Dog!" will show up, and the state is in TRIPPED. In that case, go to the next section to know how to reset Watch Dog.
  For VIS_PR3, the state should be DAMPED. If it is not, a notification "please reset Watch Dog!" will show up, and the state is in TRIPPED. In that case, go to the next section to know how to reset Watch Dog.

How to reset Watch Dogs

1. Request LSC_MICH to be READY by Guardian.
2. Open Sitemap (from Terminal, type "mk" and press return).
3. Click VIS
4. Click the suspension of which you want to reset Watch Dog

   
   === PRs case ===

5. Request SAFE by Guardian
6. Open "DETAILS" at bottom right
7. Click WATCHDOG

   
   

8. If something is red, press here to reset.

   
   

9. Click DACKILL (picture above)
10. If it is not green, press reset.

    
    

11. Click Coil Driver WD (picture above)
12. Check if everything is green. If there are red signs, push corresponding WD Pulse ON button and then OFF button

1. Request DAMPED. For PR2, ~ 10 seconds after the state becomes DAMPED, request ALIENED.
2. ~ 10 seconds after the suspension gets in a nominal state, request LSC_MICH to be OPERATION.

BS case

4. Request SAFE by Guardian

5. Open "Payload" at bottom center

6. Click WATCHDOG here.

pic

• If something is red, press here to reset.

7. Click DACKILL here.

pic pic

• If it is not green, press reset.

8. Click this button

pic

• Check if everything is green. If there are red signs, push corresponding WD Pulse ON button and then OFF button

pic

9. Request DAMPED. For PR2, ~ 10 seconds after the state becomes DAMPED, request ALIENED.

10. ~ 10 seconds after the suspension gets in a nominal state, request LSC_MICH to be OPERATION.

basic tasks

• you have to take the logbook to report the incident during the observation shift (see IFO Operational Manual)

• you have to check the check list to avoid mistake during the observation shift (Check List)

ここから先は観測シフトの仕事を簡単にまとめたものです。まだ暫定的なメモのような状態なので、適宜アップデートして下さい。ここは分かりやすさのために日本語で書きます。余裕のある方は英語版も作って下さい。

[General]

• まずコントロールルームのPCのapplication→terminal→mk→sitemapが開かれる

[DGS]

• sitemap→CDS→DAQが全部緑になっているかどうかを確認。緑じゃなければその項目のボタンを押し、statusが0×0になっているか確認。なっていなれけば宮川さんか苔山さんに連絡。

[MIF]

• sitemap→guardian→MICH_LOCKとIMC_LOCKを確認。PSLは３月中は触らない。(IMCがロックしていればIMC_MCI_TRANS_OUTPUTは0.35くらい)

[VIS]

• sitemap→VIS→PR3の画面右側のWATCHDOG、DACKILL IOPが緑かどうかを確認。

[DMG]

• DMG Check-Sheetを２時間おきに書く。コントロールルーム隣のサーバールームのPCを見て、Check-SheetのIn case of normalを満たしているか確認。Is the log outputs normal?は、PC画面に赤か黄のメッセージが出てこなければOK。

[klog]

• klogに干渉計の状況を簡単に報告。

useful information

• terminology

• how to search JGW document