Diff for "KAGRA/Commissioning/Phase1/Operation/ShiftManual"

Differences between revisions 5 and 55 (spanning 50 versions)

Contents

Control Room Overview

pic

How to use Guardian

Accessing to the guardian screen

In the sitemap, you can click on the link for the guardian overview screen.

It pops up the following screen,

Knowing the current state and requested state

How to request a state

Click on the gray bar in the middle.

Then, choose the desired state.

How to know the status of the interferometer

Look at one of the TV monitor in the control room. If "ON", it is in OPERATION mode.

If "OFF", check the guardian overview screen

Check the state of LSC_MICH. First check if the request state of LSC_MICH is OPERATION. If it is not, request OPERATION.
If the state is READY, ENGAGE_SERVO, ENGAGE_BOOST, MICH_LOCKED, CALIBRATION_INJECTION, or ACTUATORCAL_INJECTION, the interferometer is now on the way to be OPERATION state. It will be ready soon.
$/!\$ If it does not enter OPERATION state in a few mins. Call the interferometer experts.

Check the status of IMC_LOCK, VIS_BS, VIS_PR2, VIS_PR3. (Note that VIS_PRM is not used for now, so just ignore it)
For IMC_LOCK, every thing should be green and IMC should be back automatically.

For example, this is how the IMC_LOCK guardian should normally look like.

$/!\$ If it does not come back in ~ 10 mins, call interferometer/IOO experts.
For VIS_PR2 and VIS_BS, the state should be ALIGNED. If inot, a notification "please reset Watch Dog!" will show up, and the state is in TRIPPED. In that case, go to the next section to know how to reset Watch Dog.
For VIS_PR3, the state should be DAMPED. If it is not, a notification "please reset Watch Dog!" will show up, and the state is in TRIPPED. In that case, go to the next section to know how to reset Watch Dog.

How to reset Watch Dogs

Request LSC_MICH to be READY by Guardian.
Open Sitemap (from Terminal, type "mk" and press return).
Click VIS
Click the suspension of which you want to reset Watch Dog
Go to PRs case or BS case

PRs case

Request SAFE by Guardian
Open "DETAILS" at bottom right,
- and you will find PRs overview screen
Click WATCHDOG
If something is red, press here to reset.
Click DACKILL (see the picture above, PRs overview sceen)
If it is not green, press reset.
Click Coil Driver WD (picture above, PRs overview sceen)
Check if everything is green. If there are red signs, push corresponding WD Pulse ON button and then OFF button
Request DAMPED. For PR2, ~ 10 seconds after the state becomes DAMPED, request ALIENED.
~ 10 seconds after the suspension gets in a nominal state, request LSC_MICH to be OPERATION.

BS case

Request SAFE by Guardian
Open "Payload" at bottom center,
- and you will find BS payload overview screen
Click WATCHDOG
If something is red, press here to reset.
Click DACKILL (see the picture above for BS overview screen)
If it is not green, press reset.
Click Coil Driver WD (see the picture above for BS overview screen)
Check if everything is green. If there are red signs, push corresponding WD Pulse ON button and then OFF button
Request DAMPED. For PR2, ~ 10 seconds after the state becomes DAMPED, request ALIENED.
~ 10 seconds after the suspension gets in a nominal state, request LSC_MICH to be OPERATION.

-  ⇤ ← Revision 5 as of 2018-04-28 16:09:19 → 
  Size: 4595
  Editor: YutaroEnomoto
  Comment:
+   ← Revision 55 as of 2018-04-28 18:41:02 → ⇥
  Size: 4758
  Editor: YutaroEnomoto
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 1:
-Describe KAGRA/Commissioning/Phase1/Operation/ShiftManual here. TEST
+ . <<TableOfContents(2)>>
 Line 3:
-=== Control Room Overview ===
+== Control Room Overview ==
 Line 6:
-=== How to use Guardian ===
pics
+== How to use Guardian ==
=== Accessing to the guardian screen ===
 . In the sitemap, you can click on the link for the guardian overview screen.
 {{attachment:sitemap_guardian.png||height="172",width="430"}} <<BR>> It pops up the following screen, <<BR>>  {{attachment:guardian_howto3.png||height="281",width="434"}}
-Line 9:
+Line 11:
-=== How to know the status of the interferometer ===
 * Look at the monitor here. If "ON", it is in OPERATION mode. If "OFF", it is not; something is strange
+=== Knowing the current state and requested state ===
 . {{attachment:guardian_howto4.png||height="281",width="434"}}
-Line 12:
+Line 14:
-screen shots
+=== How to request a state ===
 . Click on the gray bar in the middle.<<BR>> {{attachment:guardian_howto.png||height="298",width="433"}} <<BR>> Then, choose the desired state.<<BR>> {{attachment:guardian_howto2.png||height="299",width="434"}}
-Line 14:
+Line 17:
- * If "OFF", check this screen
+== How to know the status of the interferometer ==
 . Look at one of the TV monitor in the control room. If "ON", it is in OPERATION mode.
 {{attachment:obs_state.png||height="233",width="465"}}
 <<BR>>If "OFF", check the guardian overview screen<<BR>>
 {{attachment:guardian_howto3.png||height="281",width="434"}}
 <<BR>>Check the state of LSC_MICH. First check if the request state of LSC_MICH is OPERATION. If it is not, request OPERATION.<<BR>>
 {{attachment:guardian_howto4.png||height="281",width="434"}}
 . If the state is ''READY, ENGAGE_SERVO, ENGAGE_BOOST, MICH_LOCKED, CALIBRATION_INJECTION'', or ''ACTUATORCAL_INJECTION'', the interferometer is now on the way to be OPERATION state. It will be ready soon.
 <<BR>> /!\ ''' If it does not enter OPERATION state in a few mins. Call the interferometer experts.'''<<BR>>
-Line 16:
+Line 27:
-screen shots
+ Check the status of ''IMC_LOCK, VIS_BS, VIS_PR2, VIS_PR3''. (Note that ''VIS_PRM'' is not used for now, so just ignore it)
 <<BR>>For IMC_LOCK, every thing should be green and IMC should be back automatically. <<BR>>
-Line 18:
+Line 30:
-. Check the state of LSC_MICH. First check if the request state of LSC_MICH is OPERATION. If it is not, request OPERATION.
+ {{attachment:IMC_guardian.png||height="293",width="453"}}<<BR>>
 For example, this is how the IMC_LOCK guardian should normally look like.<<BR>>
 {{attachment:IMC_guardian_status.png||height="281",width="407"}}<<BR>>
 /!\ '''If it does not come back in ~ 10 mins, call interferometer/IOO experts.'''<<BR>>
 For VIS_PR2 and VIS_BS, the state should be ALIGNED. If inot, a notification "please reset Watch Dog!" will show up, and the state is in TRIPPED. In that case, go to the next section to know how to reset Watch Dog.
 <<BR>> For VIS_PR3,  the state should be DAMPED.
 If it is not, a notification "please reset Watch Dog!" will show up, and the state is in TRIPPED. In that case, go to the next section to know how to reset Watch Dog.
-Line 20:
+Line 38:
-Screen shot
+== How to reset Watch Dogs ==
 0. Request LSC_MICH to be READY by Guardian.
-Line 22:
+Line 41:
-. If the state is READY, ENGAGE_SERVO, ENGAGE_BOOST, MICH_LOCKED, CALIBRATION_INJECTION, or ACTUATORCAL_INJECTION, the interferometer is now on the way to be OPERATION state. It will be ready soon. If it will not enter OPERATION state in a few mins, something is wrong. Call interferometer experts.
  . If it is in DOWN state, go to 3.
+. Open Sitemap (from Terminal, type "mk" and press return).
-Line 25:
+Line 43:
-. Check the status of IMC_LOCK, VIS_BS, VIS_PR2, VIS_PR3. (Note that VIS_PRM is not used for now, so just ignore it)
+. Click VIS
-Line 27:
+Line 45:
- -- For IMC_LOCK, every thing should be green and IMC should be back automatically. If it will not come back in ~ 10 mins, call interferomter/IOO experts.
+. Click the suspension of which you want to reset Watch Dog
-Line 29:
+Line 47:
- -- For VIS_PR2 and VIS_BS, the state should be ALIGNED. If it is not, a notification "please reset WatchDog!" will show up, and the state is in TRIPPED. In that case, go to the next section to know how to reset WatchDog.
+ {{attachment:VISALL.png||width="407"}}<<BR>>
-Line 31:
+Line 49:
- -- For VIS_PR3,  the state should be DAMPED. If it is not, a notification "please reset WatchDog!" will show up, and the state is in TRIPPED. In that case, go to the next section to know how to reset WatchDog.
+. Go to PRs case or BS case
-Line 33:
+Line 51:
-=== basic tasks ===
 * you have to take the logbook to report the incident during the observation shift (see [[http://gwwiki.icrr.u-tokyo.ac.jp/JGWwiki/KAGRA/Observation/iKAGRA/Manual/MIF|IFO Operational Manual]])
+=== PRs case ===
 .
 .
 .
 .
 .
 4. Request SAFE by Guardian
-Line 36:
+Line 59:
- * you have to check the check list to avoid mistake during the observation shift ([[http://gwdoc.icrr.u-tokyo.ac.jp/DocDB/0049/T1604975/005/CheckList_20160324.pdf|Check List]])
+. Open "DETAILS" at bottom right,
-Line 38:
+Line 61:
-ここから先は観測シフトの仕事を簡単にまとめたものです。まだ暫定的なメモのような状態なので、適宜アップデートして下さい。ここは分かりやすさのために日本語で書きます。余裕のある方は英語版も作って下さい。
+ {{attachment:PRTOP.png||width="300"}}<<BR>>
  and you will find PRs overview screen
-Line 40:
+Line 64:
-[General]
+ {{attachment:PR.png||width="800"}}<<BR>>
 
 6. Click WATCHDOG
-Line 42:
+Line 68:
- * まずコントロールルームのPCのapplication→terminal→mk→sitemapが開かれる
+ . If something is red, press here to reset.
 {{attachment:PRWD.png||width="400"}}<<BR>>
-Line 44:
+Line 71:
-[DGS]
+. Click DACKILL (see the picture above, PRs overview sceen)
-Line 46:
+Line 73:
- * sitemap→CDS→DAQが全部緑になっているかどうかを確認。緑じゃなければその項目のボタンを押し、statusが0×0になっているか確認。なっていなれけば宮川さんか苔山さんに連絡。
+ . If it is not green, press reset.
 {{attachment:DACKILL.png||width="200"}}<<BR>>
-Line 48:
+Line 76:
-[MIF]
+. Click Coil Driver WD (picture above, PRs overview sceen)
-Line 50:
+Line 78:
- * sitemap→guardian→MICH_LOCKとIMC_LOCKを確認。PSLは３月中は触らない。(IMCがロックしていればIMC_MCI_TRANS_OUTPUTは0.35くらい)
+ . Check if everything is green. If there are red signs, push corresponding WD Pulse ON button and then OFF button
-Line 52:
+Line 80:
-[VIS]
+ {{attachment:PR_CDWD.png||width="800"}}<<BR>>
-Line 54:
+Line 82:
- * sitemap→VIS→PR3の画面右側のWATCHDOG、DACKILL IOPが緑かどうかを確認。
+. Request DAMPED. For PR2, ~ 10 seconds after the state becomes DAMPED, request ALIENED.
-Line 56:
+Line 84:
-[DMG]
+. ~ 10 seconds after the suspension gets in a nominal state, request LSC_MICH to be OPERATION.
-Line 58:
+Line 86:
- * DMG Check-Sheetを２時間おきに書く。コントロールルーム隣のサーバールームのPCを見て、Check-SheetのIn case of normalを満たしているか確認。Is the log outputs normal?は、PC画面に赤か黄のメッセージが出てこなければOK。
+=== BS case ===
 4. Request SAFE by Guardian
-Line 60:
+Line 89:
-[klog]
+. Open "Payload" at bottom center,
-Line 62:
+Line 91:
- * klogに干渉計の状況を簡単に報告。
+ {{attachment:BSTOP.png||width="250"}}<<BR>>
  and you will find BS payload overview screen
-Line 64:
+Line 94:
-=== useful information ===
 * terminology
+ {{attachment:BSpayload.png||width="800"}}<<BR>>
-Line 67:
+Line 96:
-||<#F0F0FF>Abbreviation / Acronym ||<#F0F0FF>Meaning / Explanation ||
||BS ||Beam Splitter ||
||CDS || ||
||DAQ ||Data Acquisition ||
||DAS ||Data Analysis ||
||DC ||Direct Current ||
||DET/Detchar ||Detector Characterization ||
||DGS ||Digital System ||
||DMG ||Data Management ||
||EPICS ||Experimental Physics and Industrial Control System ||
||EX/ETMX ||X Arm End Test Mass ||
||EY/ETMY ||Y Arm End Test Mass ||
||FCL ||Facility ||
||GAS ||Geometric Anti-Spring ||
||GIF ||Geophysics Interferometer ||
||Guardian ||Automation system for interferometers ||
||IFO ||Interferometer Optics ||
||IMC ||Input Mode Cleaner ||
||LSC ||Length Sensing and Control, especially for MIF ||
||MCi/e/o ||Name of three mirrors of IMC; Input, End, and Output mirrors ||
||Medm ||GUI for dealing with EPICS ||
||MI ||Michealson Interferometer ||
||MIF ||Main Interferometer ||
||OpLev ||Optical Lever; measures angle of a mirror ||
||OSEM ||Optical Sensor and ElectroMagnet ||
||PMC ||Pre-Mode Cleaner ||
||PR3 ||Type Bp’ SAS. works as the last steering mirror for MI ||
||PSL ||Pre-Stabilized Laser ||
||SAS ||Seismic Attenuation System ||
||TM ||Test Mass ||
||VAC ||Vacuum ||
||VIS ||Vibration Isolation System ||
+. Click WATCHDOG
 . If something is red, press here to reset.
 {{attachment:PRWD.png||width="400"}}<<BR>>
 Line 100:
+. Click DACKILL (see the picture above for BS overview screen)
-Line 101:
+Line 102:
- * how to search JGW document
+ . If it is not green, press reset.
 {{attachment:DACKILL.png||width="200"}}<<BR>>

 8. Click Coil Driver WD (see the picture above for BS overview screen)

 . Check if everything is green. If there are red signs, push corresponding WD Pulse ON button and then OFF button

 {{attachment:PR_CDWD.png||width="800"}}<<BR>>

 9. Request DAMPED. For PR2, ~ 10 seconds after the state becomes DAMPED, request ALIENED.

 10. ~ 10 seconds after the suspension gets in a nominal state, request LSC_MICH to be OPERATION.