• Diff for "KAGRA/Commissioning/Phase1/Operation/ShiftManual"

Control Room Overview

pic

How to use Guardian

Accessing to the guardian screen

• In the sitemap, you can click on the link for the guardian overview screen.

  
  It pops up the following screen,
  

Knowing the current state and requested state

How to request a state

• Click on the gray bar in the middle.
  
  Then, choose the desired state.
  

How to know the status of the interferometer

• Look at one of the TV monitor in the control room. If "ON", it is in OPERATION mode.

  
  If "OFF", check the guardian overview screen
  
  Check the state of LSC_MICH. First check if the request state of LSC_MICH is OPERATION. If it is not, request OPERATION.
  

• If the state is READY, ENGAGE_SERVO, ENGAGE_BOOST, MICH_LOCKED, CALIBRATION_INJECTION, or ACTUATORCAL_INJECTION, the interferometer is now on the way to be OPERATION state. It will be ready soon.
  If it does not enter OPERATION state in a few mins. Call the interferometer experts.
  

  Check the status of IMC_LOCK, VIS_BS, VIS_PR2, VIS_PR3. (Note that VIS_PRM is not used for now, so just ignore it)
  For IMC_LOCK, every thing should be green and IMC should be back automatically.
  

  
  For example, this is how the IMC_LOCK guardian should normally look like.
  
  If it does not come back in ~ 10 mins, call interferometer/IOO experts.
  For VIS_PR2 and VIS_BS, the state should be ALIGNED. If inot, a notification "please reset Watch Dog!" will show up, and the state is in TRIPPED. In that case, go to the next section to know how to reset Watch Dog.
  For VIS_PR3, the state should be DAMPED. If it is not, a notification "please reset Watch Dog!" will show up, and the state is in TRIPPED. In that case, go to the next section to know how to reset Watch Dog.

How to reset Watch Dogs

1. Request LSC_MICH to be READY by Guardian.
2. Open Sitemap (from Terminal, type "mk" and press return).
3. Click VIS
4. Click the suspension of which you want to reset Watch Dog

   
   

5. Go to PRs case or BS case

PRs case

1. Request SAFE by Guardian
2. Open "DETAILS" at bottom right,

   
   

3. and you will find PRs overview screen

   
   

4. Click WATCHDOG
5. If something is red, press here to reset.

   
   

6. Click DACKILL (see the picture above, PRs overview sceen)
7. If it is not green, press reset.

   
   

8. Click Coil Driver WD (picture above, PRs overview sceen)
9. Check if everything is green. If there are red signs, push corresponding WD Pulse ON button and then OFF button

   
   

10. Request DAMPED. For PR2, ~ 10 seconds after the state becomes DAMPED, request ALIENED.
11. ~ 10 seconds after the suspension gets in a nominal state, request LSC_MICH to be OPERATION.

BS case

1. Request SAFE by Guardian
2. Open "Payload" at bottom center,

   
   

   • and you will find BS payload overview screen

   
   

3. Click WATCHDOG
4. If something is red, press here to reset.

   
   

5. Click DACKILL (see the picture above for BS overview screen)
6. If it is not green, press reset.

   
   

7. Click Coil Driver WD (see the picture above for BS overview screen)
8. Check if everything is green. If there are red signs, push corresponding WD Pulse ON button and then OFF button

   
   

9. Request DAMPED. For PR2, ~ 10 seconds after the state becomes DAMPED, request ALIENED.
10. ~ 10 seconds after the suspension gets in a nominal state, request LSC_MICH to be OPERATION.