Diff for "KAGRA/Commissioning/Phase1/Operation/ShiftManual"

Differences between revisions 50 and 59 (spanning 9 versions)

Contents

Control Room Overview

How to use Guardian

Accessing to the guardian screen

In the sitemap, you can click on the link for the guardian overview screen.

It pops up the following screen,

Knowing the current state and requested state

How to request a state

Click on the gray bar in the middle.

Then, choose the desired state.

How to know the status of the interferometer

Look at one of the TV monitor in the control room. If "ON", it is in OPERATION mode.

If "OFF", check the guardian overview screen

Check the state of LSC_MICH. First check if the request state of LSC_MICH is OPERATION. If it is not, request OPERATION.
If the state is READY, ENGAGE_SERVO, ENGAGE_BOOST, MICH_LOCKED, CALIBRATION_INJECTION, or ACTUATORCAL_INJECTION, the interferometer is now on the way to be OPERATION state. It will be ready soon.
$/!\$ If it does not enter OPERATION state in a few mins. Call the interferometer experts.
Check the status of IMC_LOCK, VIS_BS, VIS_PR2, VIS_PR3. (Note that VIS_PRM is not used for now, so just ignore it)
For IMC_LOCK, every thing should be green and IMC should be back automatically.

For example, this is how the IMC_LOCK guardian should normally look like.

$/!\$ If it does not come back in ~ 10 mins, call interferometer/IOO experts.
For VIS_PR2 and VIS_BS, the state should be ALIGNED. If inot, a notification "please reset Watch Dog!" will show up, and the state is in TRIPPED. In that case, go to the next section to know how to reset Watch Dog.
For VIS_PR3, the state should be DAMPED. If it is not, a notification "please reset Watch Dog!" will show up, and the state is in TRIPPED. In that case, go to the next section to know how to reset Watch Dog.

How to reset Watch Dogs

Request LSC_MICH to be READY by Guardian.
Open Sitemap (from Terminal, type "mk" and press return).
Click VIS
Click the suspension of which you want to reset Watch Dog
Go to PRs case or BS case

PRs case

Request SAFE by Guardian
Open "DETAILS" at bottom right,
- and you will find PRs overview screen
Click WATCHDOG
- If something is red, press here to reset.
Click DACKILL (see the picture above, PRs overview sceen)
- If it is not green, press reset.
Click Coil Driver WD (picture above, PRs overview sceen) Check if everything is green. If there are red signs, push corresponding WD Pulse ON button and then OFF button
Request DAMPED. For PR2, ~ 10 seconds after the state becomes DAMPED, request ALIENED.
~ 10 seconds after the suspension gets in a nominal state, request LSC_MICH to be OPERATION.

BS case

Request SAFE by Guardian
Open "Payload" at bottom center,
- and you will find BS payload overview screen
Click WATCHDOG If something is red, press here to reset.
Click DACKILL (see the picture above for BS overview screen) If it is not green, press reset.
Click Coil Driver WD (see the picture above for BS overview screen) Check if everything is green. If there are red signs, push corresponding WD Pulse ON button and then OFF button
Request DAMPED. For PR2, ~ 10 seconds after the state becomes DAMPED, request ALIENED.
~ 10 seconds after the suspension gets in a nominal state, request LSC_MICH to be OPERATION.

-  ⇤ ← Revision 50 as of 2018-04-28 18:30:52 → 
  Size: 4529
  Editor: YutaroEnomoto
  Comment:
+   ← Revision 59 as of 2018-04-28 19:04:13 → ⇥
  Size: 4769
  Editor: YutaroEnomoto
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 4:
-pic
+ . {{attachment:image1.jpeg||width="1000"}} 

 . {{attachment:IMG_4929.jpg||width="430"}}
-Line 19:
+Line 21:
- {{attachment:obs_state.png||height="233",width="465"}}
 <<BR>>If "OFF", check the guardian overview screen<<BR>>
 {{attachment:guardian_howto3.png||height="281",width="434"}}
 <<BR>>Check the state of LSC_MICH. First check if the request state of LSC_MICH is OPERATION. If it is not, request OPERATION.<<BR>>
 {{attachment:guardian_howto4.png||height="281",width="434"}}
 . If the state is ''READY, ENGAGE_SERVO, ENGAGE_BOOST, MICH_LOCKED, CALIBRATION_INJECTION'', or ''ACTUATORCAL_INJECTION'', the interferometer is now on the way to be OPERATION state. It will be ready soon.
 <<BR>> /!\ ''' If it does not enter OPERATION state in a few mins. Call the interferometer experts.'''<<BR>>

 Check the status of ''IMC_LOCK, VIS_BS, VIS_PR2, VIS_PR3''. (Note that ''VIS_PRM'' is not used for now, so just ignore it)
 <<BR>>For IMC_LOCK, every thing should be green and IMC should be back automatically. <<BR>>

 {{attachment:IMC_guardian.png||height="293",width="453"}}<<BR>>
 For example, this is how the IMC_LOCK guardian should normally look like.<<BR>>
 {{attachment:IMC_guardian_status.png||height="281",width="407"}}<<BR>>
 /!\ '''If it does not come back in ~ 10 mins, call interferometer/IOO experts.'''<<BR>>
 For VIS_PR2 and VIS_BS, the state should be ALIGNED. If inot, a notification "please reset Watch Dog!" will show up, and the state is in TRIPPED. In that case, go to the next section to know how to reset Watch Dog.
 <<BR>> For VIS_PR3,  the state should be DAMPED.
 If it is not, a notification "please reset Watch Dog!" will show up, and the state is in TRIPPED. In that case, go to the next section to know how to reset Watch Dog.
+ {{attachment:obs_state.png||height="233",width="465"}} <<BR>>If "OFF", check the guardian overview screen<<BR>> {{attachment:guardian_howto3.png||height="281",width="434"}} <<BR>>Check the state of LSC_MICH. First check if the request state of LSC_MICH is OPERATION. If it is not, request OPERATION.<<BR>> {{attachment:guardian_howto4.png||height="281",width="434"}}
 . If the state is ''READY, ENGAGE_SERVO, ENGAGE_BOOST, MICH_LOCKED, CALIBRATION_INJECTION'', or ''ACTUATORCAL_INJECTION'', the interferometer is now on the way to be OPERATION state. It will be ready soon. <<BR>> /!\ ''' If it does not enter OPERATION state in a few mins. Call the interferometer experts.'''<<BR>> Check the status of ''IMC_LOCK, VIS_BS, VIS_PR2, VIS_PR3''. (Note that ''VIS_PRM'' is not used for now, so just ignore it) <<BR>>For IMC_LOCK, every thing should be green and IMC should be back automatically. <<BR>> {{attachment:IMC_guardian.png||height="293",width="453"}} <<BR>> For example, this is how the IMC_LOCK guardian should normally look like.<<BR>> {{attachment:IMC_guardian_status.png||height="281",width="407"}} <<BR>> /!\ '''If it does not come back in ~ 10 mins, call interferometer/IOO experts.'''<<BR>> For VIS_PR2 and VIS_BS, the state should be ALIGNED. If inot, a notification "please reset Watch Dog!" will show up, and the state is in TRIPPED. In that case, go to the next section to know how to reset Watch Dog. <<BR>> For VIS_PR3,  the state should be DAMPED. If it is not, a notification "please reset Watch Dog!" will show up, and the state is in TRIPPED. In that case, go to the next section to know how to reset Watch Dog.
-Line 41:
+Line 27:
 . Open Sitemap (from Terminal, type "mk" and press return).
-Line 43:
+Line 29:
 . Click VIS
-Line 45:
+Line 31:
-. Click the suspension of which you want to reset Watch Dog
+. Click the suspension of which you want to reset Watch Dog
 {{attachment:VISALL.png||width="407"}} <<BR>>
-Line 47:
+Line 34:
- {{attachment:VISALL.png||width="407"}}<<BR>>

 4. Go to PRs case or BS case
+. Go to PRs case or BS case
-Line 54:
+Line 39:
-. Open "DETAILS" at bottom right, and you will find PRs overview screen
+. Open "DETAILS" at bottom right,
 {{attachment:PRTOP.png||width="300"}} <<BR>>
  . and you will find PRs overview screen
 {{attachment:PR.png||width="800"}} <<BR>>
-Line 56:
+Line 44:
- {{attachment:PR.png||width="800"}}<<BR>>
 
 6. Click WATCHDOG
+. Click WATCHDOG
  . If something is red, press here to reset.
 {{attachment:PRWD.png||width="400"}} <<BR>>
-Line 60:
+Line 48:
- . If something is red, press here to reset.
 {{attachment:PRWD.png||width="400"}}<<BR>>
+. Click DACKILL (see the picture above, PRs overview sceen)
  . If it is not green, press reset.
 {{attachment:DACKILL.png||width="200"}} <<BR>>
-Line 63:
+Line 52:
-. Click DACKILL (see the picture above, PRs overview sceen)
+. Click Coil Driver WD (picture above, PRs overview sceen) Check if everything is green. If there are red signs, push corresponding WD Pulse ON button and then OFF button
 {{attachment:PR_CDWD.png||width="800"}} <<BR>>
-Line 65:
+Line 55:
- . If it is not green, press reset.
 {{attachment:DACKILL.png||width="200"}}<<BR>>
+. Request DAMPED. For PR2, ~ 10 seconds after the state becomes DAMPED, request ALIENED.
-Line 68:
+Line 57:
-. Click Coil Driver WD (picture above, PRs overview sceen)

 . Check if everything is green. If there are red signs, push corresponding WD Pulse ON button and then OFF button

 {{attachment:PR_CDWD.png||width="800"}}<<BR>>

 9. Request DAMPED. For PR2, ~ 10 seconds after the state becomes DAMPED, request ALIENED.

 10. ~ 10 seconds after the suspension gets in a nominal state, request LSC_MICH to be OPERATION.
+. ~ 10 seconds after the suspension gets in a nominal state, request LSC_MICH to be OPERATION.
-Line 81:
+Line 62:
-. Open "Payload" at bottom center
+. Open "Payload" at bottom center,
 {{attachment:BSTOP.png||width="250"}} <<BR>>
  . and you will find BS payload overview screen
 {{attachment:BSpayload.png||width="800"}} <<BR>>
-Line 83:
+Line 67:
-. Click WATCHDOG
+. Click WATCHDOG If something is red, press here to reset.
 {{attachment:PRWD.png||width="400"}} <<BR>>
-Line 85:
+Line 70:
- {{attachment:BSpayload.png||width="800"}}<<BR>>
+. Click DACKILL (see the picture above for BS overview screen) If it is not green, press reset.
 {{attachment:DACKILL.png||width="200"}} <<BR>>
-Line 87:
+Line 73:
- . If something is red, press here to reset.
 {{attachment:PRWD.png||width="400"}}<<BR>>
+. Click Coil Driver WD (see the picture above for BS overview screen) Check if everything is green. If there are red signs, push corresponding WD Pulse ON button and then OFF button
 {{attachment:PR_CDWD.png||width="800"}} <<BR>>
-Line 90:
+Line 76:
-. Click DACKILL (picture above)
+. Request DAMPED. For PR2, ~ 10 seconds after the state becomes DAMPED, request ALIENED.
-Line 92:
+Line 78:
- . If it is not green, press reset.
 {{attachment:DACKILL.png||width="200"}}<<BR>>

 8. Click Coil Driver WD (picture above)

 . Check if everything is green. If there are red signs, push corresponding WD Pulse ON button and then OFF button

 {{attachment:PR_CDWD.png||width="800"}}<<BR>>

 9. Request DAMPED. For PR2, ~ 10 seconds after the state becomes DAMPED, request ALIENED.

 10. ~ 10 seconds after the suspension gets in a nominal state, request LSC_MICH to be OPERATION.
+. ~ 10 seconds after the suspension gets in a nominal state, request LSC_MICH to be OPERATION.