Plans for trial just after ER

Noise investigation about FFUs in the corner stations by an operator

1. Workers

• Measurement 2-4
  • Team1 : Furuta, Kimura (Xend)
  • Team2 : Hayakawa, Takahashi (Yend)
  • Team3 : Tamori, Mori(Xfront)
  • Team4 : Yoshimura, TTanaka(Yfront)
  • Team5 : Miyoki, Yokozawa, Washimi, (Sensitivity Taking, Instruction to All)
  • Team6 : VIS people (temperature drift, suspension condition, in the control room)
• Measurement 5 (Standby at)
  • Washimi : (IFI)
  • Tamori : (PRM)
  • TTanaka : (MCE)
  • Kimura : (PR3)
  • Yoshimura :(BS, PR2)
  • Hayakawa : (SR2, SR3)
  • Takahashi : (SRM OMC)
  • Mori: (Pre-Room FFU switch for PSL)
  • Yokozawa : (Pre-Room FFU switch near PR3, BS)
  • Miyoki: SR cooler
  • Furuta : BS cooler
  • non : IYC cooler
• Measurement 6

  • Team1 : Furuta, Kimura (Xend) Only center area

  • Team2 : Hayakawa, Takahashi (Yend) Only center area

  • Team3,4 : Mori(BS area), TTanaka(Mori support), Itoh, Kimura(Non clean area) (CS)
  • Team5 : Miyoki, Yokozawa, Washimi (k1ctr9)
  • Team6 : VIS people (temperature drift, suspension condition, in the control room)
• Zoom1 connection or PHSで坑内一斉放送？
• 検出きのそばで大きな声を掛け合うのは得策ではない。
  1. Preparation

     • Make marks on FFU switches that are not turned off in MCE, IFI, PRM, PR3, PR2, BS, SR2, SR3, SRM, OMC with "GreenTape".
       (Operated FFU / Total FFU) table list is below.
       130 FFUs will be turned off. This corresponds to 26kW heating power.
       26kW corresponds to about two water cooler cooling power (2 x 14kW). We expect balance.

  Area Name

  MCF

  MCE

  IFI

  PRM

  PR3

  PR2

  BS

  SR2

  SR3

  SRM

  OMC

  Present (151)/Total(180)

  1/16

  2/16

  12/12

  12/12

  16/16

  20/20

  20/20

  20/20

  16/16

  16/16

  16/16

  several FFUs are disorder

  Remained in Test(35)/Total(180)

  1/16

  2/16

  2/12

  2/12

  4/16

  4/20

  4/20

  4/20

  4/16

  4/16

  4/16

• IEXYV	IEXYA	IEXYC(1F)	IEXYC(2F)	EXYT
  Present(2)/Total(10)	Present(2)/Total(10)	Present(2)/Total(10+1)	Present(4)/Total(14)	Present(3)/Total(3)	<--- KOACH are not included

• Corner Station (1F)

  180+2x24+ 2x10 + 10(Pre-Rooms) = 258 (~ 51.6kW )

2. IEXYV

   • Take a sensitivity by an operator (one of PEM member). (Miyoki, Yokozawa, Washimi)

   • Each 2 people stand by IEXYV FFU switchs. (Team1-> EXV, Team2 -> EYV, Team3->IXV ,Team4->IYV)

   • Turn off remained two FFUs at the same time. (Yokozawa -> Team1, Washimi -> team2, Miyoki -> Team3,4)

   • Take the sensitivity again before alignment will change. (Miyoki, Yokozawa, Washimi)

   • Turn on two FFUs that used to be turned on. (Yokozawa -> Team1, Washimi -> team2, Miyoki -> Team3,4)

   • If you see any change in sensitivity, we recheck one by one for IEXYV.

3. IEXYC(1/2F) and Transmission Area

   • Take a sensitivity by an operator. (Miyoki, Yokozawa, Washimi)

   • Each 2 people stand by IEXYC FFU switchs. 10 are near the KOACH, 14 near the Transmission area. (Team1-> EXC, Team2 -> EYC, Team3->IXC ,Team4->IYC)

   • Turn off remained FFUs at the same time. (Yokozawa -> Team1, Washimi -> team2, Miyoki -> Team3,4)

   • Take the sensitivity again before alignment will change. (Miyoki, Yokozawa, Washimi)

   • Turn on FFUs that used to be turned on. (Yokozawa -> Team1, Washimi -> team2, Miyoki -> Team3,4)

   • If you see any change in sensitivity, we recheck one by one for IEXYC-1F/2F.

4. IEXYA

   • Take a sensitivity by an operator. (Miyoki, Yokozawa, Washimi)

   • 2 people stand by IEXYA FFU switchs. (Team1-> EXA, Team2 -> EYA, Team3->IXA ,Team4->IYA)

   • Turn off remained two FFUs at the same time. (Yokozawa -> Team1, Washimi -> team2, Miyoki -> Team3,4)

   • Take the sensitivity again before alignment will change. (Miyoki, Yokozawa, Washimi)

   • Turn on two FFUs that used to be turned on. (Yokozawa -> Team1, Washimi -> team2, Miyoki -> Team3,4)

   • If you see any change in sensitivity, we recheck one by one for IEXYA.

5. For Corner station 1F

   2. Method(1)
      • Take a sensitivity by an operator. (Miyoki, Yokozawa, Washimi)
      • 11 people stand by (MCE, IFI, PRM), (PR3, PR2, BS), (SR2, SR3), (SRM OMC), and Pre-Room FFU switchs.
      • Turn off almost FFUs at the same time by 11 people, except for Green one.
      • Take the sensitivity again before alignment will change. (Miyoki, Yokozawa, Washimi)

      • Check the difference btw FFU operation and almost no FFU operation.
        

   3. Method(2): If the alignment change is too huge for us to take a sensitivity.
      • We turn off IYC-C and BS-C coolers at the same time when we turn off 130 FFUs.
      • Take sensitivity urgently if possible. (Miyoki, Yokozawa, Washimi)
      • Check the temp changes in the corner station.
      • If the temp seems to go down rapidly, we enlarge heating power. If the temp gose up rapidly, we turned on IYC-C again and heat up by heaters.
      • we expect do some try and error for several hours if we encounter serious temp change.
      • If alignment comes back, take sensitivity. (Miyoki, Yokozawa, Washimi)
      • If it will take too much time to recover FPMI, we give up this trial.

6. Vacuum pump stopping`

   • We want to stop vacuum pumps one by one
   • FFU would be turned on
   • If temperature or vacuum pressures drastically changed, the experiments stopped
   • two people for Xend, two people for Yend, Four people CS
   • Stop the Vacuum pump one by one with instruction of Miyoki-san or Saito-san
   • Maximum experiment time is two hours or 5p.m.

   • Manual : JGW-E1911150

Other Items