Size: 3415
Comment:
|
Size: 6882
Comment:
|
Deletions are marked like this. | Additions are marked like this. |
Line 41: | Line 41: |
* Any problems during Observation will be discussed by Miyoki, Yamamoto, Ito and related group and we decide the directions. Please report these 3 persons. | * Any problems during Observation will be discussed by Miyoki, Yamamoto, Ito and related group (and SEO members) and we decide the directions. Please report these 3 persons and in "klog" if you notice any problems. |
Line 45: | Line 45: |
*Tasks during OBS * Shift Member Duty and Manual (from Miyakawa) : |
* Expected Improvements compared with the previous ER and OBS * CAL injection reliability * Injection failure is improved ? -> Still need to monitor whether cal line is injected or not. In the case of no cal line, we should apply cal line manually. The instruction manual will be prepared by CAL group * Initial oplev (mirror alignment) condition at the starting point of relock process * Alignment recorder is installed at proper timing during lock acquisition ? -> Alignment Recorder was applied. It works good ! * ADS/BPC situation * Which are effective, which should be postponed ? -> ADS for ETMs has need more adjustment. We try ASC by using QPDs on AS table, and try more adjustment about offset for BPC/ADS. * IMC angular control * It works. * ISS stability * Improved ? , applying timing is changed ? -> Control servo was improved. However, ISS system cannot follow the power up process. So ISS was set to applied at the final stage of the LSC_LOCK guardian. It now wrorks very well. * Expected kick at the unlock timing, and known annoying excitation of a suspension system. * Guardian is implemented -> It works very well. The kick was minimized. * Off load status for each suspension. * Done according to klog ? -> TypeA, TypeBp were done, while some of Type B will be checked. * How about OMC suspensions -> They should be checked because OMC ADS will push OMMTs that has small dynamic range. * Summary page reliability is enhanced ? * hardware trouble was fixed. However, software troubles still remain. We will keep improving. * SAL (monkey) Alignment reliability * Dewhitening for TM that might contributes a bit to sensitivity should be included or not ? -> No problem. Lock_loss during LSC_LOCK guardian due to not saturation but other reason. We will check later. * When should we try SAL (monkey) alignment ? -> if you cannot IFO for 1 hours, please try SAL alignment. The beam positions on mirrors, OMC direction are important as checking list. * How much IMC output power should be selected ? -> 5W. We have no confidence that 10W can improve the sensitivity. * Additional sound proof for bellows -> done. we hope some improvement in sensitivity. * Others * Actual tasks during OBS * Shift Member Duty and Manual : * Basic monitoring and recording (by Miyakawa) * Manual (important check points) -> please write klog by selecting a category of "Observation". |
Line 49: | Line 88: |
* SAF/FCL: Weekly SAF/FCL check will be held in the morning on Tuesday (Furuta, Hayakawa, Yishimura, Kamioka-mine company) | * SAF/FCL: Weekly SAF/FCL check will be held in the morning on Tuesday (Furuta, Hayakawa, Yoshimura, Kamioka-mine company) |
Line 53: | Line 92: |
* Restricted Remote Access (from T.Yamamoto) : | * '''Restricted Remote Access (from T.Yamamoto)''' |
Line 62: | Line 101: |
Line 64: | Line 106: |
. 5/18,19 Kashiwa network stop-> no access to/form outside at Kamioka, but inside OK . 5/26 11AM~(30min?): 200V power down at Kamioka building. |
|
Line 65: | Line 109: |
* * * * * |
* Calibration (~1day) -> Yamamoto * Power recycling gain for sidebands (~ 1 day) -> * LSC and ASC sensing matrix (~ 2 days) -> Ushiba * ISS contribution, frequency noise contribution to DARM (2 days) -> Kokeyama, Miyakawa * Finesse/loss measurement for X/Y arm (~ 1 day) -> * MICH contrast defect with MICH locked and FPMI locked (~ 1 day) -> Nakano * Mode content of AS (OMC cavity scan) (~ 1 day) -> Aso, Kokeyama * Scattered light, swing test, IOO investigations (~5days) -> Yokozawa * PEM injections (~2day) -> Yokozawa * Type Bp measurement with some restricted IFO (~2days) -> Fabian * BS measurement with some restricted IFO like simple Michelson (~2days) -> Fabian * Type A measurement with some restricted IFO like Xarm (~2days) -> Lucia * Feasibility of locking DRFPMI (~ 3 week) -> Nakano |
ER200401~200407, OBS200407~200421
ER Time : From 2020/Apr/1(09:00) to 2020/Apr/7(09:00)
OBS Time : From 2020/Apr/7(17:00) to 2020/Apr/21(09:00)
- Rough Schedule (time can be shifted by 1 or 2 hours according to the task progress and delay)
Mar/29
Commissioning
Mar/30
Commissioning
Mar/31
Commissioning, ADS, BPC, IMC angular control, etc
Mar/31(pm5~)
ER start
Apr/01
(am9-pm5) CAL Day 1, (rest time) ADS, BPC, IMC angular control, etc, (am1-am9) silent mode
Apr/02
(am9-am1) ADS, BPC, IMC angular control, etc, (am1-am9) silent mode for CAL2
No JRPC meeting held, only LVEM call
Apr/03
(am9-am1) ADS, BPC, IMC angular control, etc, (am1-am9) silent mode for CAL2
Apr/04
(am9-am1) ADS, BPC, IMC angular control, etc, (am1-am9) silent mode for CAL2
Apr/05
(am9-am1) ADS, BPC, IMC angular control, FF adjustment, etc, (am1-am9) silent mode for CAL2
Apr/06
(am9-am1) Ocean Violence, (am1-am9) silent mode
Apr/07(~am9)
ER end
Apr/07(am9-pm5)
Maintenance for observation
Apr/07(pm5~)
Observation Start
Apr/09
During Observation
If we got positive results, we hope to ask something about O3c in JRPC meeting
Apr/16
During Observation
If we got positive results, we hope to ask something about O3c in JRPC meeting
Apr/21(~am9)
Observation End
Apr/21(am9 ~ )
Post Observation Activities : OMC noise injection and so on
For shifts for ER and OBS
Observation : Points to Remember
- Basic
- Any problems during Observation will be discussed by Miyoki, Yamamoto, Ito and related group (and SEO members) and we decide the directions. Please report these 3 persons and in "klog" if you notice any problems.
- If we encounter violent ocean conditions, temporal down of IFO will be selected.
- Daily morning meeting won't be held during Observation to avoid dense situation. Daily necessary information including from office staffs will be sent via e-mail during 9am-10am.
- Expected Improvements compared with the previous ER and OBS
- CAL injection reliability
Injection failure is improved ? -> Still need to monitor whether cal line is injected or not. In the case of no cal line, we should apply cal line manually. The instruction manual will be prepared by CAL group
- Initial oplev (mirror alignment) condition at the starting point of relock process
Alignment recorder is installed at proper timing during lock acquisition ? -> Alignment Recorder was applied. It works good !
- ADS/BPC situation
Which are effective, which should be postponed ? -> ADS for ETMs has need more adjustment. We try ASC by using QPDs on AS table, and try more adjustment about offset for BPC/ADS.
- IMC angular control
- It works.
- ISS stability
Improved ? , applying timing is changed ? -> Control servo was improved. However, ISS system cannot follow the power up process. So ISS was set to applied at the final stage of the LSC_LOCK guardian. It now wrorks very well.
- Expected kick at the unlock timing, and known annoying excitation of a suspension system.
Guardian is implemented -> It works very well. The kick was minimized.
- Off load status for each suspension.
Done according to klog ? -> TypeA, TypeBp were done, while some of Type B will be checked.
How about OMC suspensions -> They should be checked because OMC ADS will push OMMTs that has small dynamic range.
- Summary page reliability is enhanced ?
- hardware trouble was fixed. However, software troubles still remain. We will keep improving.
- SAL (monkey) Alignment reliability
Dewhitening for TM that might contributes a bit to sensitivity should be included or not ? -> No problem. Lock_loss during LSC_LOCK guardian due to not saturation but other reason. We will check later.
When should we try SAL (monkey) alignment ? -> if you cannot IFO for 1 hours, please try SAL alignment. The beam positions on mirrors, OMC direction are important as checking list.
How much IMC output power should be selected ? -> 5W. We have no confidence that 10W can improve the sensitivity.
Additional sound proof for bellows -> done. we hope some improvement in sensitivity.
- Others
- CAL injection reliability
- Actual tasks during OBS
- Shift Member Duty and Manual :
- Basic monitoring and recording (by Miyakawa)
Manual (important check points) -> please write klog by selecting a category of "Observation".
- Basic monitoring and recording (by Miyakawa)
- Maintenance Day Activities (from CAL, DGS, FLC/SAF etc groups)
- SAF/FCL: Weekly SAF/FCL check will be held in the morning on Tuesday (Furuta, Hayakawa, Yoshimura, Kamioka-mine company)
- DGS:
- CAL:
Restricted Remote Access (from T.Yamamoto)
- We plan to stop the access to controls@k1gate again from 17:00 on 4/7.
- If you face some emergency, please use your personal accounts in order to login DGS network.
- I ask you to use these personal accounts only for a emergency response.
If you need remote access to know the site situation, subsystem status, etc as a daily check, please join to develop remote access tools such as SummaryPage, pastavi etc.
- Unfortunately, some people probably used these accounts for daily monitoring not for a emergency response during previous run. But we need reliable observing data at least during the observing run.
- Shift Member Duty and Manual :
Post Observation Tasks : Items and necessary time
5/18,19 Kashiwa network stop-> no access to/form outside at Kamioka, but inside OK
- 5/26 11AM~(30min?): 200V power down at Kamioka building.
Calibration (~1day) -> Yamamoto
Power recycling gain for sidebands (~ 1 day) ->
LSC and ASC sensing matrix (~ 2 days) -> Ushiba
ISS contribution, frequency noise contribution to DARM (2 days) -> Kokeyama, Miyakawa
Finesse/loss measurement for X/Y arm (~ 1 day) ->
MICH contrast defect with MICH locked and FPMI locked (~ 1 day) -> Nakano
Mode content of AS (OMC cavity scan) (~ 1 day) -> Aso, Kokeyama
Scattered light, swing test, IOO investigations (~5days) -> Yokozawa
PEM injections (~2day) -> Yokozawa
Type Bp measurement with some restricted IFO (~2days) -> Fabian
BS measurement with some restricted IFO like simple Michelson (~2days) -> Fabian
Type A measurement with some restricted IFO like Xarm (~2days) -> Lucia
Feasibility of locking DRFPMI (~ 3 week) -> Nakano