Diff for "KAGRA/IFOIntegration2024/Recovery20240322"

Differences between revisions 12 and 21 (spanning 9 versions)

IMC Ecovery(20240322)

Suspensions(R.Takahashi)
- Electrical wirings
  - Coil resistances and inductances
    - MCo: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28668
    - MCi/e: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28696
  - Isolation of Wiring from coils to flanges(pico and mag-coil)
  - Fixing on tables is tight and reliable?
- Mechanical Motion
  - Smooth pico motion and its default position
  - Smooth Mag-coil motion and balance and TFs
    - balance can be adjusted after closing?
    - Health MCo: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28890
    - Health MCi: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28889
    - Health MCe: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28915
  - Gaps between magnets and coils
  - Gaps between EQ stoppers and mirrors
    - MCe: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28915
    - MCi/o: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28913
Mirror conditions(Y.Aso)
- Clean around the center?
  - MCe has a spot near the center. But its influence is expected to be small.
  - Inspection: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28856
Alignment(T.Akutsu, T.Ushiba, T.Yokozawa)
- TEM00 flashing
  - https://klog.icrr.u-tokyo.ac.jp/osl/?r=28912
- The IMC trans beam is the same as before?
  - https://klog.icrr.u-tokyo.ac.jp/osl/?r=28779
  - https://klog.icrr.u-tokyo.ac.jp/osl/?r=28839
- Beam positions on each mirror
  - They should be the same because the IMC trans was recovered in MCio?
  - How about on MCe? MCE tra QPD can be the reference.
- QPD path and centering
- Gaps between magnets and coils again
- IP1/2 dynamic range check for the IMC injection?
- Beam paths for IMC REFL.
Beam damping(T.Akutsu)
- Beam shield reinstallation
  - https://klog.icrr.u-tokyo.ac.jp/osl/?r=28927
  - https://klog.icrr.u-tokyo.ac.jp/osl/?r=28926
- Beam dampers were additionally added?
Vacuum, etc (N.Kimura, T.Uchiyama, S.Miyoki)
- Cleaning
  - No dust inside, especially on the bottom?
- Leak point was fastened tightly?
  - It will be done when the bellows are attached by Mirapro.
- MCE trans flange rotation (the past activity is in https://klog.icrr.u-tokyo.ac.jp/osl/?r=28326)
- Lift-up tool check for bellows installation. (past accident https://klog.icrr.u-tokyo.ac.jp/osl/?r=28344)
- Flange surface check to avoid leaking especially on GV_mcf
- FFU stop for the MCE/MCREFL optical table and reconstruction of the window shield (MCE, MCF?).

--- one of templates for IMC closing by Akutsu-kun in 2021.

KAGRA/IFOIntegration2024/Recovery20240322 (last edited 2024-04-05 16:16:04 by miyoki)

-  ⇤ ← Revision 12 as of 2024-03-21 12:46:20 → 
  Size: 2172
  Editor: miyoki
  Comment:
+   ← Revision 21 as of 2024-03-21 19:53:35 → ⇥
  Size: 2903
  Editor: miyoki
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 12:
+    * POM: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28914
-Line 15:
+Line 16:
+    *
-Line 22:
+Line 24:
-    * MCe:https://klog.icrr.u-tokyo.ac.jp/osl/?r=28915
+    * MCe: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28915
-Line 28:
+Line 30:
+   * Inspection: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28856
-Line 31:
+Line 34:
+   * https://klog.icrr.u-tokyo.ac.jp/osl/?r=28912
-Line 32:
+Line 36:
+   * https://klog.icrr.u-tokyo.ac.jp/osl/?r=28779
   * https://klog.icrr.u-tokyo.ac.jp/osl/?r=28839
-Line 42:
+Line 48:
+   * https://klog.icrr.u-tokyo.ac.jp/osl/?r=28927
   * https://klog.icrr.u-tokyo.ac.jp/osl/?r=28926
-Line 49:
+Line 57:
-  * MCE trans flange rotation
  * Lift-up tool check for bellows installation.
+  * MCE trans flange rotation (the past activity is in https://klog.icrr.u-tokyo.ac.jp/osl/?r=28326)
  * Lift-up tool check for bellows installation. (past accident https://klog.icrr.u-tokyo.ac.jp/osl/?r=28344)
-Line 53:
+Line 61:
+---
[[ https://paper.dropbox.com/doc/Installation-Acceptance-Document-for-MCF-and-MCE-in-spring-2021--CLlN4mKPlOUb8YO5qXgdLVeBAg-9a7b8tlqCZ2cxodEcJhGY | one of templates for IMC closing by Akutsu-kun in 2021.]]