Diff for "KAGRA/IFOIntegration2024/Recovery20240322"

Differences between revisions 3 and 27 (spanning 24 versions)

IMC Ecovery(20240322)

Suspensions(R.Takahashi)
- Electrical wirings
  - Coil resistances and inductances
    - MCo: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28668
    - MCi/e: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28696
  - Isolation of Wiring from coils to flanges(pico and mag-coil)
  - Fixing on tables is tight and reliable?
- Mechanical Motion
  - Smooth pico motion and its default position
    - MCi/o: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28907
  - Smooth Mag-coil motion and balance and TFs
    - balance can be adjusted after closing?
    - Health MCo: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28890
    - Health MCi: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28889
    - Health MCe: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28915
  - Gaps between magnets and coils
  - Gaps between EQ stoppers and mirrors
    - MCe: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28915
    - MCi/o: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28913
Mirror conditions(Y.Aso)
- Clean around the center?
  - MCe has a spot near the center. But its influence is expected to be small.
  - Inspection: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28856
Alignment(T.Akutsu, T.Ushiba, T.Yokozawa)
- TEM00 flashing
  - https://klog.icrr.u-tokyo.ac.jp/osl/?r=28912
- The IMC trans beam is the same as before?
  - https://klog.icrr.u-tokyo.ac.jp/osl/?r=28779
  - https://klog.icrr.u-tokyo.ac.jp/osl/?r=28839
- Beam positions on each mirror
  - They should be the same because the IMC trans was recovered in MCio?
  - How about on MCe? MCE tra QPD can be the reference.
- QPD path and centering
- Gaps between magnets and coils again
- IP1/2 dynamic range check for the IMC injection?
- Beam paths for IMC REFL.
Beam damping(T.Akutsu)
- Beam shield reinstallation
  - https://klog.icrr.u-tokyo.ac.jp/osl/?r=28927
  - https://klog.icrr.u-tokyo.ac.jp/osl/?r=28926
- Beam dampers were additionally added?
  - In basic, No. Relocation was done. https://klog.icrr.u-tokyo.ac.jp/osl/?r=28931
Vacuum, etc (N.Kimura, T.Uchiyama, S.Miyoki)
- Cleaning
  - No dust inside, especially on the bottom?
- Leak point was fastened tightly?
  - It will be done when the bellows are attached by Mirapro.
- MCE trans flange rotation (the past activity is in https://klog.icrr.u-tokyo.ac.jp/osl/?r=28326)
- Lift-up tool check for bellows installation. (past accident https://klog.icrr.u-tokyo.ac.jp/osl/?r=28344)
- Flange surface check to avoid leaking especially on GV_mcf
- FFU stop for the MCE/MCREFL optical table and reconstruction of the window shield (MCE, MCF?).

one of templates for IMC closing by Akutsu-kun in 2021.

??? Recovery(202404??)

KAGRA/IFOIntegration2024/Recovery20240322 (last edited 2024-04-05 16:16:04 by miyoki)

-  ⇤ ← Revision 3 as of 2024-03-21 10:30:12 → 
  Size: 1355
  Editor: miyoki
  Comment:
+   ← Revision 27 as of 2024-03-22 08:46:10 → ⇥
  Size: 3134
  Editor: RyutaroTakahashi
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 4:
- * Suspensions
+ * Suspensions(R.Takahashi)
 Line 6:
-   * Coil resistances
+   * Coil resistances and inductances
    * MCo: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28668
    *MCi/e: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28696
-Line 8:
+Line 10:
+    * MCo: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28911
    * MCe: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28910
    * POM: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28914
-Line 11:
+Line 16:
+    * MCi/o: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28907
-Line 13:
+Line 19:
+    * Health MCo: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28890
    * Health MCi: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28889
    * Health MCe: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28915
-Line 15:
+Line 24:
+    * MCe: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28915
    * MCi/o: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28913
-Line 16:
+Line 27:
- * Mirror conditions
+ * Mirror conditions(Y.Aso)
-Line 19:
+Line 30:
+   * Inspection: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28856
-Line 20:
+Line 32:
- * Alignment
+ * Alignment(T.Akutsu, T.Ushiba, T.Yokozawa)
-Line 22:
+Line 34:
+   * https://klog.icrr.u-tokyo.ac.jp/osl/?r=28912
-Line 23:
+Line 36:
+   * https://klog.icrr.u-tokyo.ac.jp/osl/?r=28779
   * https://klog.icrr.u-tokyo.ac.jp/osl/?r=28839
-Line 25:
+Line 40:
-   * How about on MCe?
+   * How about on MCe? MCE tra QPD can be the reference.
-Line 29:
+Line 44:
+  * Beam paths for IMC REFL.
-Line 30:
+Line 46:
- *Beam damping
+ *Beam damping(T.Akutsu)
-Line 32:
+Line 48:
-  * Beam dampers were additionally done?
+   * https://klog.icrr.u-tokyo.ac.jp/osl/?r=28927
   * https://klog.icrr.u-tokyo.ac.jp/osl/?r=28926
  * Beam dampers were additionally added?
   * In basic, No. Relocation was done.  https://klog.icrr.u-tokyo.ac.jp/osl/?r=28931
-Line 34:
+Line 53:
- * Vacuum
+ * Vacuum, etc (N.Kimura, T.Uchiyama, S.Miyoki)
-Line 39:
+Line 58:
-  * MCE trans flange rotation
  * Lift-up tool check for bellows installation.
+  * MCE trans flange rotation (the past activity is in https://klog.icrr.u-tokyo.ac.jp/osl/?r=28326)
  * Lift-up tool check for bellows installation. (past accident https://klog.icrr.u-tokyo.ac.jp/osl/?r=28344)
-Line 42:
+Line 61:
+  * FFU stop for the MCE/MCREFL optical table and reconstruction of the window shield (MCE, MCF?).

----

[[ https://paper.dropbox.com/doc/Installation-Acceptance-Document-for-MCF-and-MCE-in-spring-2021--CLlN4mKPlOUb8YO5qXgdLVeBAg-9a7b8tlqCZ2cxodEcJhGY | one of templates for IMC closing by Akutsu-kun in 2021.]]


------
??? Recovery(202404??)
------



------
??? Recovery(202404??)
------