Diff for "KAGRA/IFOIntegration2024/Recovery20240322"

Differences between revisions 9 and 81 (spanning 72 versions)

IMC recovery(20240322)

Suspensions(R.Takahashi)
- Mechanical Motion
  - Smooth pico motion and its default position
    - MCi/o: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28907 -> A.I. upload picth pico pictues (R.Takahashi), or taking picture for picth pico. -> https://klog.icrr.u-tokyo.ac.jp/osl/?r=28941
    - MCe: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28909 -> A.I. upload pitch, yaw pico pictures (R.Takahashi), or taking picture for pitch, yaw pico. -> https://klog.icrr.u-tokyo.ac.jp/osl/?r=28941
  - Gaps between magnets and coils -> MCo upper is the minimum, but this is the best effort.
  - Gaps between EQ stoppers and mirrors -> confirmed less than 1mm.
    - MCe: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28915
    - MCi/o: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28913
- Electrical wirings
  - Coil resistances and inductances -> A.I. Inductances should refer the past data if the coil did not change, or it will be measured again (Wasimi, 3/24(Monday morning)
    - MCo: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28668 -> A.I. MCo H4 looks high, it could be disconnection. It should be measured again (Wasimi, 3/24(Monday morning).
    - MCi/e: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28696 -> One of the MCi resistances is low, but low may have no problem. If it is high, it may have some disconnection.
  - Isolation of Wiring from coils to flanges(pico and mag-coil) -> MCi could not be accessed.
    - MCo: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28911 -> improved
    - MCe: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28910 -> improved
    - POM: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28914 -> this does not matter for the suspension.
  - Fixing on tables is tight and reliable?
- Smooth Mag-coil motion and balance and TFs
  - balance can be adjusted after closing?
  - MCi: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28938
  - MCo: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28939
  - MCe: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28940 -> A.I. Peak of pitch shifted to higher frequency from result of Feb.2. Needs remote centering for the Oplev first (Ushiba).
Mirror conditions(Y.Aso)
- Clean around the center?
  - MCe has a spot near the center. But its influence is expected to be small.
  - Inspection: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28856
Alignment(T.Akutsu, T.Ushiba, T.Yokozawa)
- TEM00 flashing
  - https://klog.icrr.u-tokyo.ac.jp/osl/?r=28912
- The IMC trans beam is the same as before?
- Beam positions on each mirror
  - They should be the same because the IMC trans was recovered in MCio?
  - How about on MCe? MCE tra QPD can be the reference.
- QPD path and centering
- Gaps between magnets and coils again
- IP1/2 dynamic range check for the IMC injection?
- Beam paths for IMC REFL.
Beam dump(T.Akutsu)
- Beam shield reinstallation
  - https://klog.icrr.u-tokyo.ac.jp/osl/?r=28927
  - https://klog.icrr.u-tokyo.ac.jp/osl/?r=28926
- Beam dumps were additionally added?
  - In basic, No. Relocation was done. https://klog.icrr.u-tokyo.ac.jp/osl/?r=28931 -> Inside of beam duct between PSL and iMC looks shining.
Vacuum, etc (N.Kimura, T.Uchiyama, S.Miyoki)
- Cleaning
  - No dust inside, especially on the bottom? -> A.I. before closing.
- Leak point was fastened tightly? -> A.I. when closing.
  - It will be done when the bellows are attached by Mirapro.
- MCE trans flange rotation (the past activity is in https://klog.icrr.u-tokyo.ac.jp/osl/?r=28326) -> it will be done on Mon.
- Lift-up tool check for bellows installation. (past accident https://klog.icrr.u-tokyo.ac.jp/osl/?r=28344)
- Flange surface check to avoid leaking especially on GV_mcf
- FFU stop for the MCE/MCREFL optical table and reconstruction of the window shield (MCE, MCF?). -> measurement of length of legs.

one of templates for IMC closing by Akutsu-kun in 2021.

Summary

TF of MCe had a shift of peak frequency on pitch. Ushiba-kun will measure it again with the well-centered oplev. It will be reported at the recovery meeting or later.
All others should be OK for closing IMC chambers.
- The resistance of the Coil of MCo H4 looked high. Washimi-kun will measure it again on Monday, but it won't stop closing anyway.
- Washimi-kun will measure inductances again on Monday.
- Check no dust inside, especially on the bottom before closing.
- Check the leak points are fastened tightly when closing.

X-Pcal Recovery(20240402)

Dan's presentation files
- Path2 drift is concerns. However, we expect we can compensate for the drift by using pico-mirrors.
- 5% power loss is concerned. It should be checked on 3~4 April. --> klog#29065
- Pcal-X noise in the Cal line is OK? --> klog#29075

EXC Recovery(202404??)

Suspension health check (Takahashi, Ushiba)
- A01: Cable check
- A02 Porality Check Type-A/C-Payload
- A03 Rubbing Check
- A04: Range and Calibration
- A05: Watchdog Setting: Skip
- A06: Height Measurement
  - Done: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28780
- A08: Calibration
  - A
  - C
- A09: Spectrum(spectra of IM/MN photosensors.)
  - OK https://klog.icrr.u-tokyo.ac.jp/osl/?r=29102
- A10: Transfer Function
  - Some GASs are strange? : https://klog.icrr.u-tokyo.ac.jp/osl/?r=29100
Oplev Check (Yokozawa, Akutsu)
- MN: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28905
- TM:
- PF:
Green flash at REFL and Trans PD
- REFL: OK
- Trans: No beam on PD.
X-Pcal homeworks
- Loss of power of ~ 5%: https://klog.icrr.u-tokyo.ac.jp/osl/?r=29081
- Cleaning: https://klog.icrr.u-tokyo.ac.jp/osl/?r=29091
Windows Cleaning
- Done: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28976,
- Blanck ports:
Tcam (Yokozawa and ChenDan, and Yamamoto)
TMSX optical system (Akutsu and his selected persons)
Baffle PDs (Yokozawa and his selected persons)
NAB, WAB (Akutsu)
- NAB: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28757
- WAB: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28758, https://klog.icrr.u-tokyo.ac.jp/osl/?r=28627
Vacuum system (Kimura-san / Uchiyama-kun and their selected persons)
- tie rods adjustment between EXC and TMSX to avoid stress when the only EXC side is pumped down.
- Replaced flange
Cryo-system (Kimura-san and his selected persons)
- All temp signals are obtained?

*** Recovery(202404??)

KAGRA/IFOIntegration2024/Recovery20240322 (last edited 2024-04-05 16:16:04 by miyoki)

-  ⇤ ← Revision 9 as of 2024-03-21 12:36:47 → 
  Size: 1636
  Editor: miyoki
  Comment:
+   ← Revision 81 as of 2024-04-05 11:52:39 → ⇥
  Size: 7095
  Editor: miyoki
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 2:
-IMC Ecovery(20240322)
+IMC recovery(20240322)
 Line 5:
-  * Electrical wirings
   * Coil resistances and inductances
   * Isolation of Wiring from coils to flanges(pico and mag-coil)
   * Fixing on tables is tight and reliable?
-Line 11:
+Line 7:
-   * Smooth Mag-coil motion and balance and TFs
    * balance can be adjusted after closing?
   * Gaps between magnets and coils
   * Gaps between EQ stoppers and mirrors
+    * MCi/o: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28907 -> --(A.I. upload picth pico pictues (R.Takahashi), or taking picture for picth pico.)-- -> https://klog.icrr.u-tokyo.ac.jp/osl/?r=28941
    * MCe: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28909 -> --(A.I. upload pitch, yaw pico pictures (R.Takahashi), or taking picture for pitch, yaw pico.)-- -> https://klog.icrr.u-tokyo.ac.jp/osl/?r=28941
   * Gaps between magnets and coils -> MCo upper is the minimum, but this is the best effort.
   * Gaps between EQ stoppers and mirrors -> confirmed less than 1mm.
    * MCe: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28915
    * MCi/o: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28913
  * Electrical wirings
   * Coil resistances and inductances -> A.I. Inductances should refer the past data if the coil did not change, or it will be measured again  (Wasimi, 3/24(Monday morning)
    * MCo: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28668 -> A.I. MCo H4 looks high, it could be disconnection. It should be measured again (Wasimi, 3/24(Monday morning).
    *MCi/e: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28696 -> One of the MCi resistances is low, but low may have no problem. If it is high, it may have some disconnection.
   * Isolation of Wiring from coils to flanges(pico and mag-coil) -> MCi could not be accessed.
    * MCo: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28911 -> improved
    * MCe: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28910 -> improved
    * POM: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28914 -> this does not matter for the suspension.
   * Fixing on tables is tight and reliable? 
  * Smooth Mag-coil motion and balance and TFs
   * balance can be adjusted after closing?
   * MCi: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28938
   * MCo: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28939
   * MCe: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28940 -> A.I. Peak of pitch shifted to higher frequency from result of Feb.2. Needs remote centering for the Oplev first (Ushiba).
-Line 19:
+Line 31:
+   * Inspection: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28856
-Line 22:
+Line 35:
+   * https://klog.icrr.u-tokyo.ac.jp/osl/?r=28912
-Line 23:
+Line 37:
+   * https://klog.icrr.u-tokyo.ac.jp/osl/?r=28779
   * https://klog.icrr.u-tokyo.ac.jp/osl/?r=28839
   * https://klog.icrr.u-tokyo.ac.jp/osl/?r=28937
-Line 31:
+Line 48:
- *Beam damping(T.Akutsu)
+ *Beam dump(T.Akutsu)
-Line 33:
+Line 50:
-  * Beam dampers were additionally added?
+   * https://klog.icrr.u-tokyo.ac.jp/osl/?r=28927
   * https://klog.icrr.u-tokyo.ac.jp/osl/?r=28926
  * Beam dumps were additionally added?
   * In basic, No. Relocation was done.  https://klog.icrr.u-tokyo.ac.jp/osl/?r=28931 -> Inside of beam duct between PSL and iMC looks shining.
-Line 37:
+Line 57:
-   * No dust inside, especially on the bottom?
  * Leak point was fastened tightly?
+   * No dust inside, especially on the bottom? -> A.I. before closing.
  * Leak point was fastened tightly? -> A.I. when closing.
-Line 40:
+Line 60:
-  * MCE trans flange rotation
  * Lift-up tool check for bellows installation.
+  * MCE trans flange rotation (the past activity is in https://klog.icrr.u-tokyo.ac.jp/osl/?r=28326) -> it will be done on Mon.
  * Lift-up tool check for bellows installation. (past accident https://klog.icrr.u-tokyo.ac.jp/osl/?r=28344)
-Line 43:
+Line 63:
-  * FFU stop for the MCE/MCREFL optical table and reconstruction of the window shield (MCE, MCF?).
+  * FFU stop for the MCE/MCREFL optical table and reconstruction of the window shield (MCE, MCF?). -> measurement of length of legs.

----

[[ https://paper.dropbox.com/doc/Installation-Acceptance-Document-for-MCF-and-MCE-in-spring-2021--CLlN4mKPlOUb8YO5qXgdLVeBAg-9a7b8tlqCZ2cxodEcJhGY | one of templates for IMC closing by Akutsu-kun in 2021.]]


----
Summary
----
 * TF of MCe had a shift of peak frequency on pitch. Ushiba-kun will measure it again with the well-centered oplev. It will be reported at the recovery meeting or later. 
 * All others should be OK for closing IMC chambers.
  * The resistance of the Coil of MCo H4 looked high. Washimi-kun will measure it again on Monday, but it won't stop closing anyway.
  * Washimi-kun will measure inductances again on Monday.
  * Check no dust inside, especially on the bottom before closing.
  * Check the leak points are fastened tightly when closing.


------
X-Pcal Recovery(20240402)
------
 * [[ https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=15709 | Dan's presentation files ]]
  * Path2 drift is concerns. However, we expect we can compensate for the drift by using pico-mirrors.
  * 5% power loss is concerned. It should be checked on 3~4 April. --> [[  https://klog.icrr.u-tokyo.ac.jp/osl/?r=29065  |  klog#29065 ]]
  * Pcal-X noise in the Cal line is OK? --> [[https://klog.icrr.u-tokyo.ac.jp/osl/?r=29075 | klog#29075 ]] 

------
EXC Recovery(202404??)
------
 * Suspension health check (Takahashi, Ushiba)
  * A01: Cable check
   *
  * A02 Porality Check Type-A/C-Payload
   *
  * A03 Rubbing Check
   *
  * A04: Range and Calibration
   *
  * A05: Watchdog Setting: Skip
  * A06: Height Measurement
   * Done: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28780
  * A08: Calibration
   *A
   *C
  * A09: Spectrum(spectra of IM/MN photosensors.)
   * OK https://klog.icrr.u-tokyo.ac.jp/osl/?r=29102
  * A10: Transfer Function
   * Some GASs are strange? : https://klog.icrr.u-tokyo.ac.jp/osl/?r=29100
 * Oplev Check (Yokozawa, Akutsu)
  * MN: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28905
  * TM:
  * PF:
 * Green flash at REFL and Trans PD
  * REFL: OK
  * Trans: No beam on PD.

 * X-Pcal homeworks
  * Loss of power of ~ 5%: https://klog.icrr.u-tokyo.ac.jp/osl/?r=29081
  * Cleaning: https://klog.icrr.u-tokyo.ac.jp/osl/?r=29091

 *Windows Cleaning
  * Done: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28976, 
  * Blanck ports: 

 * Tcam (Yokozawa and ChenDan, and Yamamoto)

 * TMSX optical system (Akutsu and his selected persons)

 * Baffle PDs (Yokozawa and his selected persons)

 * NAB, WAB (Akutsu)
  * NAB: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28757
  * WAB: https://klog.icrr.u-tokyo.ac.jp/osl/?r=28758, https://klog.icrr.u-tokyo.ac.jp/osl/?r=28627

 * Vacuum system (Kimura-san / Uchiyama-kun and their selected persons)
  * tie rods adjustment between EXC and TMSX to avoid stress when the only EXC side is pumped down.
  * Replaced flange

 * Cryo-system (Kimura-san and his selected persons)
  * All temp signals are obtained?


------
*** Recovery(202404??)
------





------
*** Recovery(202404??)
------