Diff for "KAGRA/Subgroups/DGS/Projects/StepperMotor"

Differences between revisions 4 and 19 (spanning 15 versions)

Overview

DriverList

Configuration

Setup

ユーザがTelnetでコマンドを送信するには，（１）Nport5150のRS485-Ethernet変換の設定(2)TMCM6110の環境設定が必要である。

Nport5150の設定

Please change the IP address according to where you want to use it.

TMCM6110の設定

Do not use in ASCII mode. Use binary mode.

How to control the motors from python script

(At point at 17/10/5)

* Go to the directory: /kagra/Dropbox/Subsystem/VIS/TypeBp/Script/steppingmotor/

* start ipython

* in ipython, type the command as follows.

from Trinamic_control6110 import *
driver = Trinamic_control6110()
driver.connectTCP('your ip address', 4001)
driver.reconnect()

and if it says '...ok', the motors are replying.

* In order to move it,

driver.setTargetPosition(step,motor_number)

Insert the relative step in to the 'step', and insert the motor number into 'motor_number.'

KAGRA/Subgroups/DGS/Projects/StepperMotor (last edited 2022-08-02 16:57:38 by satoru.ikeda)

-  ⇤ ← Revision 4 as of 2017-04-25 08:50:23 → 
  Size: 952
  Editor: KousekiMiyo
  Comment:
+   ← Revision 19 as of 2017-10-05 18:42:17 → ⇥
  Size: 1438
  Editor: AyakaShoda
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 5:
-Line 6:
+Line 7:
-ステッピングモータは計算機ネットワーク上(10.68.150.**)にあるドライバ(TMCM6110)から制御され，ユーザはドライバにたいしてTelnetで制御コマンドを送信する形になっている。もともとTMCM6110への制御コマンドはRS485でしか受け付けないので，NportのRS485-Ethernet変換器をつかって，TMCM6110をネットワーク上においている。ネットワークにおいたことによってユーザの環境に依存せずにTelnetでコマンド送信ができ，計算機ネットワークにいればどこにいても操作ができるので便利である。

以前はRealCOMモードとよばれる，Ethernetケーブルをつかって仮想的なCOMポートをユーザのPCに開いて制御コマンドを送っていた。セットアップのマニュアルは[]を参考。
+[[attachment:configuration|{{attachment:スクリーンショット 2017-05-01 19.20.17.png|latest sensitivity curve|width="600"}}]]
-Line 14:
+Line 10:
+ユーザがTelnetでコマンドを送信するには，（１）Nport5150のRS485-Ethernet変換の設定(2)TMCM6110の環境設定が必要である。
=== Nport5150の設定 ===
[[attachment:configuration|{{attachment:SerialSetting.png|latest sensitivity curve|width="900"}}]]

[[attachment:configuration|{{attachment:NportSetting.png|latest sensitivity curve|width="900"}}]]

[[attachment:configuration|{{attachment:NetworkSetting.PNG|latest sensitivity curve|width="900"}}]]

Please change the IP address according to where you want to use it.

=== TMCM6110の設定 ===
Do not use in ASCII mode. Use binary mode.

=== How to control the motors from python script ===
(At point at 17/10/5)

* Go to the directory: /kagra/Dropbox/Subsystem/VIS/TypeBp/Script/steppingmotor/

* start ipython

* in ipython, type the command as follows.
{{{
from Trinamic_control6110 import *
driver = Trinamic_control6110()
driver.connectTCP('your ip address', 4001)
driver.reconnect()
}}}
and if it says '...ok', the motors are replying.

* In order to move it,
{{{
driver.setTargetPosition(step,motor_number)
}}} 
Insert the relative step in to the 'step', and insert the motor number into 'motor_number.'