Diff for "KAGRA/Subgroups/IOO/MC/IMCServoHardware"

Differences between revisions 1 and 17 (spanning 16 versions)

Input Mode Cleaner Hardware

Location of the servo components

Green lines represent cabling.

MC REFL optical table: PD, QPD
Around MCi, MCe chambers: OpLev
MC rack: I-Q demodulators, MC board, MC RTS computer, Coil drivers, Picomotor Drivers
Laser room: TTFSS box, AOM

Questions
Where to put TTFSS ? Do we need a rack inside the laser room ?

Demodulator

Assigned to Aso

Use 4ch I-Q demodulators for the moment. JGW-D1402413

Necessary channels: 1ch for Length PD, 8ch for WFS QPDs.

	Qty	Interface	Size	Location	Description
4ch I-Q demod	3	SMA, BNC(monitor)	1U	MC rack
Coax. cables	9	BNC->SMA	10m?
Power cables	3		1m

MC board

Assigned to Michimura and Nakano

LIGOの回路図を見て，機能ブロック図を描く

→　LIGO-D1002416-v5(pole/zeroの位置は適宜調整されている可能性あり。参考: LIGO-D040180(回路図)、LIGO-E1200177(LIGOでの変更履歴))

KAGRAで必要な修正点はあるか?

→ なさそう。

AOMとの接続は単なるBNCケーブル?

→ SMBとSMCは必要(参照: JGW-T1402941)。

Interface between MC board and RTS

Assigned to Michimura and Nakano

Cables (Type, Number, Length)

→ MC board: JGW-T1402941 (配線図あり)

→ TTFSS: JGW-G1402963 (配線図あり)

Interface between RTS and MC suspensions

Assigned to Ohishi, Saito, Miyakawa

ToCoilDriver

Type	Number	Length
RTS - Coil Driver(LEMO)	9 =(length, pitch, yaw)×3MCSs	?m×6(MCI, MCO), ?m×3(MCE)
Coil Driver - Feed through(BNC)	12 (=4coils×3MCSs)	? a few m
Feed through - Coil(BNC)	12 (=4coils×3MCSs)	3m

ToPicoMotor

Picomotor Driver(LAN cable)	6	?m
Picomotor Driver(LAN port) - Feed through（Burndy）	?	?m
Feed through - MCSs(Burndy)	3	3m

Reference 1. http://gwwiki.icrr.u-tokyo.ac.jp/JGWwiki/KAGRA/Subgroups/DGS/Projects/PicoMotor

2. http://gwclio.icrr.u-tokyo.ac.jp/lcgtsubgroup/vibrationisolation/2014/10/picomotor-controls-by-epics-at-payload-prototype-test.html

3. http://gwclio.icrr.u-tokyo.ac.jp/lcgtsubgroup/digitalsys

KAGRA/Subgroups/IOO/MC/IMCServoHardware (last edited 2015-01-05 14:03:11 by YutaMichimura)

-  ⇤ ← Revision 1 as of 2014-10-28 13:30:16 → 
  Size: 663
  Editor: YoichiAso
  Comment:
+   ← Revision 17 as of 2014-11-10 11:23:31 → ⇥
  Size: 2810
  Editor: NaokoOhishi
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 3:
-Assigned to Aso
+[[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=2968|Drawing]]

Green lines represent cabling.

MC REFL optical table: PD, QPD<<BR>> Around MCi, MCe chambers: !OpLev <<BR>> MC rack: I-Q demodulators, MC board, MC RTS computer, Coil drivers, Picomotor Drivers<<BR>> Laser room: TTFSS box, AOM

Questions<<BR>> Where to put TTFSS ? Do we need a rack inside the laser room ?
-Line 8:
+Line 14:
-Interface between RTS and MC suspensions
+Use 4ch I-Q demodulators for the moment.  [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=2413|JGW-D1402413]]

Necessary channels: 1ch for Length PD, 8ch for WFS QPDs.
||<tablewidth="833px" tableheight="200px"> ||Qty ||Interface ||Size ||Location ||Description ||
||4ch I-Q demod ||3 ||SMA, BNC(monitor) ||1U ||MC rack || ||
||Coax. cables ||9 ||BNC->SMA ||10m? || || ||
||Power cables ||3 || ||1m|| || ||
-Line 14:
+Line 29:
+→　[[https://dcc.ligo.org/LIGO-D1002416/public|LIGO-D1002416-v5]](pole/zeroの位置は適宜調整されている可能性あり。参考: [[https://dcc.ligo.org/LIGO-D040180/public|LIGO-D040180]](回路図)、[[https://dcc.ligo.org/LIGO-E1200177/public|LIGO-E1200177]](LIGOでの変更履歴))
-Line 15:
+Line 33:
+→ なさそう。
-Line 16:
+Line 37:
+→ SMBとSMCは必要(参照: [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/DocDB/ShowDocument?docid=2941|JGW-T1402941]])。
-Line 22:
+Line 45:
+→ MC board: [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/DocDB/ShowDocument?docid=2941|JGW-T1402941]] (配線図あり)

→ TTFSS: [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=2963|JGW-G1402963]] (配線図あり)
-Line 25:
+Line 52:
- * Cables (Type, Number, Length)
 * Picomotor (Driver, Software)
+ToCoilDriver
||Type || Number||Length||
||RTS - Coil Driver(LEMO) ||9 =(length, pitch, yaw)×3MCSs ||?m×6(MCI, MCO), ?m×3(MCE)||
||Coil Driver - Feed through(BNC)||12 (=4coils×3MCSs)||? a few m||
||Feed through - Coil(BNC)|| 12 (=4coils×3MCSs)||3m||
ToPicoMotor
||Picomotor Driver(LAN cable)||6||?m||
||Picomotor Driver(LAN port) - Feed through（Burndy）||?||?m||
||Feed through - MCSs(Burndy)||3 || 3m||

Reference
1. http://gwwiki.icrr.u-tokyo.ac.jp/JGWwiki/KAGRA/Subgroups/DGS/Projects/PicoMotor

2. http://gwclio.icrr.u-tokyo.ac.jp/lcgtsubgroup/vibrationisolation/2014/10/picomotor-controls-by-epics-at-payload-prototype-test.html

3. http://gwclio.icrr.u-tokyo.ac.jp/lcgtsubgroup/digitalsys