|
Size: 2870
Comment:
|
Size: 3366
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 43: | Line 43: |
| || ||Qty ||Interface ||Size ||Location ||Description || ||MC common mode servo board ||1 ||BNC ||1U ||IO rack ||not designed yet for KAGRA || ||AOM ||1 ||SMC || ||PSL ||Crystal Technology 3110-197 || ||AOM driver ||1 ||SMA,SMB || ||PSL ||1110AF-AEFO-1.5 || ||Coax. cables ||2 ||BNC->SMA ||5m? || ||length depend on RF distribution || ||Coax. cables ||1 ||BNC->SMA ||3m? || ||length depend on RF distribution || ||Power cables ||7 || ||1m|| || || (Qty needed for TTFSS is also included) |
Input Mode Cleaner Hardware
Location of the servo components
Green lines represent cabling.
MC REFL optical table: PD, QPD
Around MCi, MCe chambers: OpLev
MC rack: I-Q demodulators, MC board, MC RTS computer, Coil drivers, Picomotor Drivers
Laser room: TTFSS box, AOM
Questions
Where to put TTFSS ? Do we need a rack inside the laser room ?
Demodulator
Assigned to Aso
Use 4ch I-Q demodulators for the moment. JGW-D1402413
Necessary channels: 1ch for Length PD, 8ch for WFS QPDs.
|
Qty |
Interface |
Size |
Location |
Description |
4ch I-Q demod |
3 |
SMA, BNC(monitor) |
1U |
MC rack |
|
Coax. cables |
9 |
BNC->SMA |
10m? |
|
|
Power cables |
3 |
|
1m |
|
|
MC board
Assigned to Michimura and Nakano
- LIGOの回路図を見て，機能ブロック図を描く
→ LIGO-D1002416-v5(pole/zeroの位置は適宜調整されている可能性あり。参考: LIGO-D040180(回路図)、LIGO-E1200177(LIGOでの変更履歴))
- KAGRAで必要な修正点はあるか?
→ なさそう。
- AOMとの接続は単なるBNCケーブル?
→ SMBとSMCは必要(参照: JGW-T1402941)。
Interface between MC board and RTS
Assigned to Michimura and Nakano
|
Qty |
Interface |
Size |
Location |
Description |
MC common mode servo board |
1 |
BNC |
1U |
IO rack |
not designed yet for KAGRA |
AOM |
1 |
SMC |
|
PSL |
Crystal Technology 3110-197 |
AOM driver |
1 |
SMA,SMB |
|
PSL |
1110AF-AEFO-1.5 |
Coax. cables |
2 |
BNC->SMA |
5m? |
|
length depend on RF distribution |
Coax. cables |
1 |
BNC->SMA |
3m? |
|
length depend on RF distribution |
Power cables |
7 |
|
1m |
|
|
(Qty needed for TTFSS is also included)
- Cables (Type, Number, Length)
→ MC board: JGW-T1402941 (配線図あり)
→ TTFSS: JGW-G1402963 (配線図あり)
Interface between RTS and MC suspensions
Assigned to Ohishi, Saito, Miyakawa
Type |
Number |
Length |
RTS - Coil Driver(LEMO) |
9 =(length, pitch, yaw)×3MCSs |
?m×6(MCI, MCO), ?m×3(MCE) |
Coil Driver - Feed through(BNC) |
12 (=4coils×3MCSs) |
? a few m |
Feed through - Coil(BNC) |
12 (=4coils×3MCSs) |
3m |
RTS-Picomotor Driver(LAN cable) |
6 |
?m |
Picomotor Driver(LAN port) - Feed through（Burndy） |
? |
?m |
Feed through - MCSs(Burndy) |
3 |
3m |
Reference
1. http://gwwiki.icrr.u-tokyo.ac.jp/JGWwiki/KAGRA/Subgroups/DGS/Projects/PicoMotor