3324
Comment:
|
5297
|
Deletions are marked like this. | Additions are marked like this. |
Line 4: | Line 4: |
[[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=3018|Cable rack drawing]] |
|
Line 20: | Line 22: |
||Power cables ||3 || ||1m|| || || |
||Power cables ||3 || ||1m || || || |
Line 34: | Line 33: |
→ なさそう。 | → なさそう(pole/zeroの位置は適宜修正必要)。 |
Line 43: | Line 42: |
* Cabling: [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/DocDB/ShowDocument?docid=2984|JGW-D1402984]] (MC board related [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/DocDB/ShowDocument?docid=2941|JGW-T1402941]], TTFSS related [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=2963|JGW-G1402963]]) * List below is for whole iKAGRA PSL+IMC. Electronics are listed at [[KAGRA/Subgroups/MIF/AEL]] page. |
|
Line 44: | Line 46: |
||MC common mode servo board ||1 ||BNC ||1U ||IO rack ||not designed yet for KAGRA || ||AOM ||1 ||SMC || ||PSL ||Crystal Technology 3110-197 || ||AOM driver ||1 ||SMA,SMB || ||PSL ||1110AF-AEFO-1.5 || ||Coax. cables ||2 ||BNC->SMA ||5m? || ||length depend on RF distribution || ||Coax. cables ||1 ||BNC->SMA ||3m? || ||length depend on RF distribution || ||Power cables ||7 || ||1m|| || || (Qty needed for TTFSS is also included) * Cables (Type, Number, Length) → MC board: [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/DocDB/ShowDocument?docid=2941|JGW-T1402941]] (配線図あり) → TTFSS: [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=2963|JGW-G1402963]] (配線図あり) |
||RF splitter ||1 ||BNC/SMA||-||PSL||8 if there's no distributor || ||Coax. cable ||11 ||BNC/SMA ||2m ||PSL|| || ||Coax. cable ||6 ||BNC/SMA ||6m ||PSL to IO rack|| || ||Coax. cable ||9 ||BNC/SMA ||5m ||IMC REFL to IO rack || || ||Coax. cable||7||BNC/SMA||2m||IO rack|| || ||Ribbon cable ||1 ||Dsub 37pin ||0.1m||PSL ||TTFSS Interface to TTFSS|| ||Ribbon cable ||2 ||Dsub 25pin ||6m||PSL to IO rack ||TTFSS Interface and PMC Servo Board(?)|| ||Ribbon cable ||2 ||Dsub 15pin ||6m ||PSL to IO rack||for QPDs IP_A/B|| ||Ribbon cable ||2 ||Dsub 15pin ||5m ||IMC REFL to IO rack||for QPDs IMCR_A/B|| ||Ribbon cable ||2 ||Dsub 15pin ||40m ||IMC TRANS to IO rack||for QPDs IMCT_A/B|| ||Ribbon cable||3||Dsub 9pin||6m||PSL to IO rack||for PDs PMCR, PMCT, FRCT|| ||Ribbon cable||1||Dsub 9pin||5m||IMC REFL to IO rack||for PD IMCR|| ||Ribbon cable||1||Dsub 9pin||40m||IMC TRANS to IO rack||for PD IMCT|| ||Power cable ||4 ||3pin tap||6m ||from PSL to IO rack ||for TTFSS Interface and PMC Servo Board(?) || ||Power cable ||14 ||3pin tap||2m ||IO rack || || ||AC cable ||7 || ||2m||PSL, IO rack || || ||AC extension cable||1 || ||6m ||from PSL to IO rack || || |
Line 62: | Line 68: |
||Type || Number||Length|| ||RTS - Coil Driver(LEMO) ||9 =(length, pitch, yaw)×3MCSs ||?m×6(MCI, MCO), ?m×3(MCE)|| ||Coil Driver - Feed through(BNC)||12 (=4coils×3MCSs)||? a few m|| ||Feed through - Coil(BNC)|| 12 (=4coils×3MCSs)||3m|| |
||Type ||Number ||Length || ||RTS - Coil Driver(LEMO) ||9 =(length, pitch, yaw)×3MCSs ||?m×6(MCI, MCO), ?m×3(MCE) || ||Coil Driver - Feed through(BNC) ||12 (=4coils×3MCSs) ||? a few m || ||Feed through - Coil(BNC) ||12 (=4coils×3MCSs) ||3m || |
Line 67: | Line 77: |
||RTS-Picomotor Driver(LAN cable)||6||?m|| ||Picomotor Driver(LAN port) - Feed through(Burndy)||?||?m|| ||Feed through - MCSs(Burndy)||3 || 3m|| |
||RTS-Picomotor Driver(LAN cable) ||6 ||?m || ||Picomotor Driver(LAN port) - Feed through(Burndy) ||? ||?m || ||Feed through - MCSs(Burndy) ||3 ||3m || |
Line 77: | Line 90: |
3. http://gwclio.icrr.u-tokyo.ac.jp/lcgtsubgroup/digitalsystem/2012/03/ | 3. http://gwclio.icrr.u-tokyo.ac.jp/lcgtsubgroup/digitalsystem/2012/03/new-focus-picomotor-controlled-at-stda.html === Interface between oplev and RTS === [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/DocDB/ShowDocument?docid=3017|JGW-D1403017]] * Electronics and cables needed for IMC mirror oplevs are listed || ||Qty ||Interface ||Size ||Location ||Description || ||SLD|| 3 || || ||pylons||needs +15 ~ +24VDC || ||conversion connector|| 3 ||3pin tap -> SLD connector|| ||pylons||for converting DC power cable to a connector for SLD module|| ||Oplev QPD|| 3 ||Dsub 15pin || ||pylons|| || ||Oplev QPD Interface|| 2 ||Dsub 15pin || ||MC rack||1 Interface for 2 QPDs || ||Ribbon cable ||2 ||Dsub 15pin ||4m ||MCF to MC rack||for QPDs|| ||Ribbon cable ||1 ||Dsub 15pin ||35m ||MCE to MC rack||for QPDs|| ||Power cable ||2 ||3pin tap||4m ||MCF to MC rack ||for SLD|| ||Power cable ||1 ||3pin tap||35m ||MCE to MC rack ||for SLD|| ||Power cable ||3 ||3pin tap||2m ||MC rack ||for Oplev QPD Interface|| |
Input Mode Cleaner Hardware
Location of the servo components
Green lines represent cabling.
MC REFL optical table: PD, QPD
Around MCi, MCe chambers: OpLev
MC rack: I-Q demodulators, MC board, MC RTS computer, Coil drivers, Picomotor Drivers
Laser room: TTFSS box, AOM
Questions
Where to put TTFSS ? Do we need a rack inside the laser room ?
Demodulator
Assigned to Aso
Use 4ch I-Q demodulators for the moment. JGW-D1402413
Necessary channels: 1ch for Length PD, 8ch for WFS QPDs.
|
Qty |
Interface |
Size |
Location |
Description |
4ch I-Q demod |
3 |
SMA, BNC(monitor) |
1U |
MC rack |
|
Coax. cables |
9 |
BNC->SMA |
10m? |
|
|
Power cables |
3 |
|
1m |
|
|
MC board
Assigned to Michimura and Nakano
- LIGOの回路図を見て,機能ブロック図を描く
→ LIGO-D1002416-v5(pole/zeroの位置は適宜調整されている可能性あり。参考: LIGO-D040180(回路図)、LIGO-E1200177(LIGOでの変更履歴))
- KAGRAで必要な修正点はあるか?
→ なさそう(pole/zeroの位置は適宜修正必要)。
- AOMとの接続は単なるBNCケーブル?
→ SMBとSMCは必要(参照: JGW-T1402941)。
Interface between MC board and RTS
Assigned to Michimura and Nakano
Cabling: JGW-D1402984 (MC board related JGW-T1402941, TTFSS related JGW-G1402963)
List below is for whole iKAGRA PSL+IMC. Electronics are listed at KAGRA/Subgroups/MIF/AEL page.
|
Qty |
Interface |
Size |
Location |
Description |
RF splitter |
1 |
BNC/SMA |
- |
PSL |
8 if there's no distributor |
Coax. cable |
11 |
BNC/SMA |
2m |
PSL |
|
Coax. cable |
6 |
BNC/SMA |
6m |
PSL to IO rack |
|
Coax. cable |
9 |
BNC/SMA |
5m |
IMC REFL to IO rack |
|
Coax. cable |
7 |
BNC/SMA |
2m |
IO rack |
|
Ribbon cable |
1 |
Dsub 37pin |
0.1m |
PSL |
TTFSS Interface to TTFSS |
Ribbon cable |
2 |
Dsub 25pin |
6m |
PSL to IO rack |
TTFSS Interface and PMC Servo Board(?) |
Ribbon cable |
2 |
Dsub 15pin |
6m |
PSL to IO rack |
for QPDs IP_A/B |
Ribbon cable |
2 |
Dsub 15pin |
5m |
IMC REFL to IO rack |
for QPDs IMCR_A/B |
Ribbon cable |
2 |
Dsub 15pin |
40m |
IMC TRANS to IO rack |
for QPDs IMCT_A/B |
Ribbon cable |
3 |
Dsub 9pin |
6m |
PSL to IO rack |
for PDs PMCR, PMCT, FRCT |
Ribbon cable |
1 |
Dsub 9pin |
5m |
IMC REFL to IO rack |
for PD IMCR |
Ribbon cable |
1 |
Dsub 9pin |
40m |
IMC TRANS to IO rack |
for PD IMCT |
Power cable |
4 |
3pin tap |
6m |
from PSL to IO rack |
for TTFSS Interface and PMC Servo Board(?) |
Power cable |
14 |
3pin tap |
2m |
IO rack |
|
AC cable |
7 |
|
2m |
PSL, IO rack |
|
AC extension cable |
1 |
|
6m |
from PSL to IO rack |
|
Interface between RTS and MC suspensions
Assigned to Ohishi, Saito, Miyakawa
Type |
Number |
Length |
RTS - Coil Driver(LEMO) |
9 =(length, pitch, yaw)×3MCSs |
?m×6(MCI, MCO), ?m×3(MCE) |
Coil Driver - Feed through(BNC) |
12 (=4coils×3MCSs) |
? a few m |
Feed through - Coil(BNC) |
12 (=4coils×3MCSs) |
3m |
RTS-Picomotor Driver(LAN cable) |
6 |
?m |
Picomotor Driver(LAN port) - Feed through(Burndy) |
? |
?m |
Feed through - MCSs(Burndy) |
3 |
3m |
Reference
1. http://gwwiki.icrr.u-tokyo.ac.jp/JGWwiki/KAGRA/Subgroups/DGS/Projects/PicoMotor
Interface between oplev and RTS
- Electronics and cables needed for IMC mirror oplevs are listed
|
Qty |
Interface |
Size |
Location |
Description |
SLD |
3 |
|
|
pylons |
needs +15 ~ +24VDC |
conversion connector |
3 |
3pin tap -> SLD connector |
|
pylons |
for converting DC power cable to a connector for SLD module |
Oplev QPD |
3 |
Dsub 15pin |
|
pylons |
|
Oplev QPD Interface |
2 |
Dsub 15pin |
|
MC rack |
1 Interface for 2 QPDs |
Ribbon cable |
2 |
Dsub 15pin |
4m |
MCF to MC rack |
for QPDs |
Ribbon cable |
1 |
Dsub 15pin |
35m |
MCE to MC rack |
for QPDs |
Power cable |
2 |
3pin tap |
4m |
MCF to MC rack |
for SLD |
Power cable |
1 |
3pin tap |
35m |
MCE to MC rack |
for SLD |
Power cable |
3 |
3pin tap |
2m |
MC rack |
for Oplev QPD Interface |