Differences between revisions 27 and 66 (spanning 39 versions)
⇤ ← Revision 27 as of 2014-12-22 13:10:53 →
Size: 1550
Editor: YutaMichimura
Comment:
← Revision 66 as of 2018-09-10 12:44:51 → ⇥
Size: 3220
Editor: YutaMichimura
Comment:
Deletions are marked like this. Additions are marked like this.
Line 2: Line 2:

 * [[KAGRA/Subgroups/IOO/OutputTables/Optics| Optics for Output Tables]]
Line 3: Line 6:
||name ||size and height ||closest chamber ||beam height ||q-param/position/angle of the beams ||
||MC front || 1.2 x 2.4m x h 0.940m ||MCF chamber || 1.134m - 0.012m ||IMC REFL:1.5165+16.8465i/1189mm from PSL side edge/87.6034deg||
||MCT || 1m x 1m x h 0.955m ||MCE chamber || 1.149m - 0.027m ||IMC TRANS:27.9850+16.8465i/465mm from PSL side edge/88.6689deg||
||REFL || 1.2 x 2.4m x h 0.947m ||IFI chamber || 1.141m - 0.019m || ||
||IMMT2 || 1m x 1m x h 0.947m (temporary) ||IFI chamber || 1.141m - 0.019m || ||
||SR2 || 1m x 1m x h 1.000m (temporary for iKAGRA AS) ||SR2 chamber || 1.217m || ||
||ETMX || 1m x 1m x h 0.986m (temporary) ||EXA chamber || 1.200m || ||
||ETMY || 1m x 1m x h 0.986m (temporary) ||EYA chamber || 1.200m || ||		 ||name ||size and height ||closest chamber ||beam height ||optical layout drawing / status ||
||IMC REFL ||1m x 1m x h 0.940m (CL-1010TS) ||MCF chamber ||1.134m - 0.012m ||[[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=3412|JGW-D1503412]] / to be used for POY (or POX) for bKAGRA, purchased(2015/9), installed ||
||MCT ||1m x 1m x h 0.955m ||MCE chamber ||1.149m - 0.027m ||[[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=3412|JGW-D1503412]] / purchased(2014/10), installed ||
||REFL ||1m x 1m x h 0.947m (CL-1010TS) ||IFI chamber ||1.141m - 0.019m ||to be used for POX (or POY) for bKAGRA, purchased(2015/9), returned from VIS (2016/2) ||
||IMMT1T ||300mm x 400mm + extension(250mm x 300mm) (breadboard on pylon) ||MMT chamber ||??? ||installed([[http://klog.icrr.u-tokyo.ac.jp/osl/?r=862|klog #862]]) ||
Line 15: Line 15:
||POX || 1m x 1m x h 1.043m (temporary) || SR3 chamber || 1.257m || ||
||POY || 1m x 1m x h 0.936m (temporary) || PR3 chamber || 1.150m || ||
||POP || 1.2 x 2.4m x h 0.970m || PR2 chamber || 1.184m || ||
||POS || 1.2 x 2.4m x h 1.000m || SR2 chamber || 1.217m || ||
||AS || 1.2 x 2.4m x h 1.000m || SRM chamber || 1.271m || ||		 ||IMC REFL ||1.2m x 2.4m x h 0.940m ||MCF chamber -Y ||1.134m - 0.012m ||[[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=3412|JGW-D1503412]] / used for IMC REFL (2016/11),purchased(2014/10) ||
||REFL ||1.2m x 2.4m x h 0.947m ||IFI chamber -Y ||1.141m - 0.019m ||installed(2017/2); was used at Kashiwa ; purchased(2015/9) ||
||IMMT2 ||1m x 1m x h 0.947m (CL-1010TS) ||IFI chamber +Y ||1.141m - 0.019m ||VIS is borrowing now, purchased(2014/10) ||
||ETMX ||1.2m　x　2.0m x h 1.006m ||EXT chamber +X (table is put on mortar surface) ||1.200m ||brought to Xend(2017/2/23);size confirmed(2016/7/11) ||
||ETMY ||1.2m　x　2.0m x h 1.006m ||EYT chamber +Y (table is put on mortar surface) ||1.200m ||brought to Yend(2017/2/24);size confirmed(2016/7/11) ||
||POX ||1m x 1m x h 1.043m (CL-1010TS) ||SR3 chamber -X (-X side is more spacious) ||1.257m ||will be used for AS for bKAGRAp1, used for REFL in iKAGRA, purchased(2015/9) ||
||POY ||1m x 1m x h 0.936m (CL-1010TS) ||PR3 chamber +Y ||1.150m ||used for IMC REFL in iKAGRA->now used as workbench for IMMT work, purchased(2015/9) ; anchor holes are at -Y side, but anchors are not needed and it should be at +Y for VIS work(2017/4/14)||
||POP ||1.2m x 2.4m x h 0.9645m ||PR2 chamber -Y ||1.204m from concrete floor ||now at outside of MCF clean booth;reuse iKAGRA PSL table instead of buying a new one ||
||POS ||1.2m x 2.4m x h 1.018m ||SR2 chamber -X ||1.212m from concrete floor ||now at OMMT chamber;height confirmed(2016/11/14) ||
||AS ||1.2m x 2.4m x h 1.078m ||OMC chamber +X (table is put on mortar surface) ||1.272m ||installed(2017/3/23);height confirmed(2016/11/14) ||
Line 21: Line 26:
* Beam height written here is from the mortar surface.
* Beam height written here is from the mortar surface unless otherwise noted.
Line 25: Line 31:
* Difference between the beam height from the concrete surface and the height of the optical table should be larger than 7.6 inch (0.19m) * Difference between the beam height from the floor (concrete surface or mortar surface) and the height of the optical table should be larger than 7.6 inch (0.19m)
Line 28: Line 34:

* iKAGRA AS table is omitted because we are not using AS port for iKAGRA 3km Michelson

KAGRA Output Optical Tables

iKAGRA

name

size and height

closest chamber

beam height

optical layout drawing / status

IMC REFL

1m x 1m x h 0.940m (CL-1010TS)

MCF chamber

1.134m - 0.012m

JGW-D1503412 / to be used for POY (or POX) for bKAGRA, purchased(2015/9), installed

MCT

1m x 1m x h 0.955m

MCE chamber

1.149m - 0.027m

JGW-D1503412 / purchased(2014/10), installed

REFL

1m x 1m x h 0.947m (CL-1010TS)

IFI chamber

1.141m - 0.019m

to be used for POX (or POY) for bKAGRA, purchased(2015/9), returned from VIS (2016/2)

IMMT1T

300mm x 400mm + extension(250mm x 300mm) (breadboard on pylon)

MMT chamber

???

installed(klog #862)

bKAGRA

name

size and height

closest chamber

beam height

IMC REFL

1.2m x 2.4m x h 0.940m

MCF chamber -Y

1.134m - 0.012m

JGW-D1503412 / used for IMC REFL (2016/11),purchased(2014/10)

REFL

1.2m x 2.4m x h 0.947m

IFI chamber -Y

1.141m - 0.019m

installed(2017/2); was used at Kashiwa ; purchased(2015/9)

IMMT2

1m x 1m x h 0.947m (CL-1010TS)

IFI chamber +Y

1.141m - 0.019m

VIS is borrowing now, purchased(2014/10)

ETMX

1.2m　x　2.0m x h 1.006m

EXT chamber +X (table is put on mortar surface)

1.200m

brought to Xend(2017/2/23);size confirmed(2016/7/11)

ETMY

1.2m　x　2.0m x h 1.006m

EYT chamber +Y (table is put on mortar surface)

1.200m

brought to Yend(2017/2/24);size confirmed(2016/7/11)

POX

1m x 1m x h 1.043m (CL-1010TS)

SR3 chamber -X (-X side is more spacious)

1.257m

will be used for AS for bKAGRAp1, used for REFL in iKAGRA, purchased(2015/9)

POY

1m x 1m x h 0.936m (CL-1010TS)

PR3 chamber +Y

1.150m

used for IMC REFL in iKAGRA->now used as workbench for IMMT work, purchased(2015/9) ; anchor holes are at -Y side, but anchors are not needed and it should be at +Y for VIS work(2017/4/14)

POP

1.2m x 2.4m x h 0.9645m

PR2 chamber -Y

1.204m from concrete floor

now at outside of MCF clean booth;reuse iKAGRA PSL table instead of buying a new one

POS

1.2m x 2.4m x h 1.018m

SR2 chamber -X

1.212m from concrete floor

now at OMMT chamber;height confirmed(2016/11/14)

AS

1.2m x 2.4m x h 1.078m

OMC chamber +X (table is put on mortar surface)

1.272m

installed(2017/3/23);height confirmed(2016/11/14)

* Beam height written here is from the mortar surface unless otherwise noted.

* Mortar thickness is about 20mm by design.

* Difference between the beam height from the floor (concrete surface or mortar surface) and the height of the optical table should be larger than 7.6 inch (0.19m)

* See JGW-D1402607

* iKAGRA AS table is omitted because we are not using AS port for iKAGRA 3km Michelson

KAGRA/Subgroups/IOO/OutputTables (last edited 2022-05-11 06:27:47 by ChenDan)