Size: 76
Comment:
|
Size: 8538
Comment:
|
Deletions are marked like this. | Additions are marked like this. |
Line 1: | Line 1: |
KAGRA/Subgroups/MIF/AELについて、ここに記述してください。 | = Analog Electronics for Interferometer Control = == Electronics == || Name || Height || Schematics || Power || Description || || RF PD in air || - || [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=1280|JGW-D1201280]] || +-18V ||has DC, RF HI, RF LOW outputs|| || BB PD in air || - || || ||broadband (for 2*f1, 2*f2 and nonresonant SB ?)|| || RF QPD in air || - || [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/DocDB/ShowDocument?docid=2631|JGW-D1402631]] || ||should have 4 RF outputs, 4 DC outputs|| || DC PD in air || - || || ||should have DC output|| || DC QPD in air || - || || ||should have 4 DC outputs|| || RF PD for green in air || - || || ||BB can be OK || || DC PD for green in air || - || || || || || DC QPD for green in air || - || || || || || TTFSS || - || [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=1823|JGW-D1301823]] || from Interface || || || TTFSS Interface || - || [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=1831|JGW-D1301831]] || +-17V,+-24V,+-200V || || || PMC Servo Board || - || || +-17V,+-24V,+-200V? ||may need interface board || || AOM Driver || - ||Crystal Technology 1110AF-AEFO-1.5||+28V || || || RF Oscillator Source || ? || Agilent || AC ||for the time being || || Frequency Doubler || 1U || || ||for sideband power monitor || || Difference Frequency Generator || || || ||for nonresonant sidebands || || Phase Frequency Discriminator || 1U || || ||for ALS || || RF Distribution Amplifier || 1U || || +-17V,+-24V ||split into 8 || || Delay Line Phase Shifter || 1U || || +15V? ||1 input, 1 output? || || Quad IQ Demodulator LSC || 1U || [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=2413|JGW-D1402413]] || +-18V ||4 LOs for 4 demodulation channels || || Quad IQ Demodulator ASC || 1U || [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=2413|JGW-D1402413]] || +-18V ||1 LO for 4 demodulation channels || || Common Mode Servo Board || 1U || || +-17V,+-24V ||2 inputs, slow and fast outputs || || PD Interface Board || 1U || || +-18V ||for ribbon cables from RF PDs. 8 inputs? || || QPD Interface Board || 1U || || +-18V? ||for ribbon cables from RF QPDs. 8 inputs? || || ISS Board || ? || || || || || PLL Servo Board || ? || || || || || OMC Servo Board || ? || || || || * References: [[https://awiki.ligo-wa.caltech.edu/aLIGO/RfDesign|awiki/RfDesign]], [[https://awiki.ligo-wa.caltech.edu/aLIGO/LSC_Photodetectors|awiki/LSC_Photodetectors]] == Photodetector list == * [[KAGRA/Subgroups/MIF/AEL/Photodetectors|Photodetectors]] * List of the Interferometer Detection Ports [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/DocDB/ShowDocument?docid=2982|JGW-T1402982]] == For each rack == * KAGRA ISC Electrical Components Layout [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/DocDB/ShowDocument?docid=2986|JGW-D1402986]] * In-vac PD/QPDs are not considered yet!!! === IO rack === Located between PSL and MCF chamber. Generates RF for fIMC, f1, f2, f3, 2*f1, 2*f2, f3-f1, f3-f2, fALSX, and fALSY. Has servo circuits for FRC, IMC, and ISS. Takes care of PD/QPDs on PSL, IMC REFL, IMC TRANS, IMMT1, and IMMT2 tables. || Name || Height || Description || ||||||PD/QPD|| || Quad IQ Demodulator LSC || 1U || for IMCR(fIMC), IMMT2T(f1), IMMT2T(f2), (1ch left)|| || PD Interface Board || 1Ux?? || how many?? for PMCR, PMCT, REFCAVR, REFCAVT, IMCR, IMCT, IMMT1T, IMMT2T|| || QPD Interface Board || 1Ux?? || how many?? for IP_A/B, IMCR_A/B, IMCT_A/B, IMMT2T_A/B|| ||||||fIMC|| || RF Oscillator Source || ? || for fIMC sideband (also for Refcav) || || RF Distribution Amplifier || 1U || for fIMC. to PSL EOM, to Delay Line for Refcav, to Delay Line for IMC LSC, to IQ Demod x 2, (3ch left)|| || Delay Line Phase Shifter || 1U || for TTFSS LO(Refcav lock) || || Delay Line Phase Shifter || 1U || for CM board LO(IMC LSC) || || Common Mode Servo Board || 1U || for IMC servo|| || Quad IQ Demodulator ASC || 1U || for IMCR_A QPD(fIMC)|| || Quad IQ Demodulator ASC || 1U || for IMCR_B QPD(fIMC)|| ||||||f1|| || RF Oscillator Source || ? || for f1 sideband || || RF Distribution Amplifier || 1U || for f1. to PSL EOM, to LSC racks, to Frequency Doubler, to Diff. Freq. Generator, to IMMT2T LO, (3ch left)|| || Frequency Doubler || 1U || f1 to 2*f1 for ISC racks || ||||||f2|| || RF Oscillator Source || ? || for f2 sideband || || RF Distribution Amplifier || 1U || for f2. to PSL EOM, to LSC racks, to Frequency Doubler, to Diff. Freq. Generator, to IMMT2T LO, (3ch left)|| || Frequency Doubler || 1U || f1 to 2*f1 for ISC racks || ||||||f3|| || RF Oscillator Source || ? || for f3 to splitter || || (RF splitter) || - || split f3 into 2 for Diff. Freq. Generators || || Diff. Freq. Generator || ?? || make f3-f1 for ISC racks || || Diff. Freq. Generator || ?? || make f3-f2 for ISC racks || ||||||fALSX,fALSY|| || RF Oscillator Source || ? || for fALSX sideband for ISC racks || || RF Oscillator Source || ? || for fALSY sideband for ISC racks || ||||||Others|| || ISS Board || ?? || || === ISC racks === Stands for LSC, ASC1, ASC2 and AUX racks located between PR3 and PR2 chambers. Has servo circuits for CARM, ALSX, and ALSY. Takes care of PD/QPDs on REFL, POP, POS, POX, POY, and AS tables. || Name || Height || Description || ||||||PD/QPD|| || Quad IQ Demodulator LSC || 1U || for REFL(f1), REFL(f2), REFL_NRSB(f3-f1), REFL_NRSB(f3-f2)|| || Quad IQ Demodulator LSC || 1U || for POP(f1), POP(f2), SPOP(2*f1), SPOP(2*f2)|| || Quad IQ Demodulator LSC || 1U || for SPOS(2*f1), SPOS(2*f2), POP_GR(fALSY), POS_GR(fALSX)|| || Quad IQ Demodulator LSC || 1U || for POX(f1), POX(f2), POY(f1), POY(f2)|| || Quad IQ Demodulator LSC || 1U || for AS(f1), (3ch left)|| || PD Interface Board || 1Ux?? || how many?? for REFL, REFL_NRSB, POP, SPOP, SPOS, POX, POY, AS, OMCT, POP_GR, POS_GR|| || QPD Interface Board || 1Ux?? || how many?? for REFL_A/B, POP_A/B, AS_A/B, OMCT_A/B|| ||||||f1|| || RF Distribution Amplifier || 1U || for f1. to Delay Line for CARM, POP LO, POX LO, POY LO, AS LO, (3ch left) || || Delay Line Phase Shifter || 1U || for CM board LO(CARM)|| || Common Mode Servo Board || 1U || for CARM servo|| || Quad IQ Demodulator ASC || 1U || for REFL_A QPD(f1)|| || Quad IQ Demodulator ASC || 1U || for REFL_B QPD(f1)|| || Quad IQ Demodulator ASC || 1U || for POP_A QPD(f1)|| || Quad IQ Demodulator ASC || 1U || for POP_B QPD(f1)|| || Quad IQ Demodulator ASC || 1U || for AS_A QPD(f1)|| || Quad IQ Demodulator ASC || 1U || for AS_B QPD(f1)|| ||||||f2|| || RF Distribution Amplifier || 1U || for f2. to REFL LO, POP LO, POX LO, POY LO, (4ch left) || || Quad IQ Demodulator ASC || 1U || for REFL_A QPD(f2)|| || Quad IQ Demodulator ASC || 1U || for REFL_B QPD(f2)|| || Quad IQ Demodulator ASC || 1U || for POP_A QPD(f2)|| || Quad IQ Demodulator ASC || 1U || for POP_B QPD(f2)|| ||||||2*f1,2*f2|| || (RF splitter) || - || split 2*f1 into 2 for SPOP LO, SPOS LO || || (RF splitter) || - || split 2*f2 into 2 for SPOP LO, SPOS LO || ||||||f3-f1,f3-f2|| |||||||| ||||||fALSX,fALSY|| || (RF splitter) || - || split fALSX into 2 for POS EOM, Delay Line for ALSX || || Delay Line Phase Shifter || 1U || for CM board LO(ALSX)|| || Common Mode Servo Board || 1U || for ALSX servo|| || (RF splitter) || - || split fALSY into 2 for POP EOM, Delay Line for ALSY || || Delay Line Phase Shifter || 1U || for CM board LO(ALSY)|| || Common Mode Servo Board || 1U || for ALSY servo|| || PLL Servo Board || ? || || || PLL Servo Board || ? || || === EX4 rack === Located close to EXC chamber. Takes care of PD/QPDs on TRX table. || Name || Height || Description || ||||||PD/QPD|| || PD Interface Board || 1Ux?? || how many?? for TRX, TRX_GR|| || QPD Interface Board || 1Ux?? || how many?? for TRX_A/B, TRX_GR_A/B|| === EY4 rack === Located close to EYC chamber. Components should be the same as those in EX4. ---- == Plan (as of 2012-08) == * Test fabrication of RF PD (by the end of September ?, test in October) * Compile other analog circuit designs from LIGO into KAGRA spec. (by the end of October) * Design frequency stabilization related circuits with NAOJ group (by the end of FY2012) [[KAGRA/Subgroups/MIF/AEL/RFPD|RFPD]] |
Analog Electronics for Interferometer Control
Electronics
Name |
Height |
Schematics |
Power |
Description |
RF PD in air |
- |
+-18V |
has DC, RF HI, RF LOW outputs |
|
BB PD in air |
- |
|
|
broadband (for 2*f1, 2*f2 and nonresonant SB ?) |
RF QPD in air |
- |
|
should have 4 RF outputs, 4 DC outputs |
|
DC PD in air |
- |
|
|
should have DC output |
DC QPD in air |
- |
|
|
should have 4 DC outputs |
RF PD for green in air |
- |
|
|
BB can be OK |
DC PD for green in air |
- |
|
|
|
DC QPD for green in air |
- |
|
|
|
TTFSS |
- |
from Interface |
|
|
TTFSS Interface |
- |
+-17V,+-24V,+-200V |
|
|
PMC Servo Board |
- |
|
+-17V,+-24V,+-200V? |
may need interface board |
AOM Driver |
- |
Crystal Technology 1110AF-AEFO-1.5 |
+28V |
|
RF Oscillator Source |
? |
Agilent |
AC |
for the time being |
Frequency Doubler |
1U |
|
|
for sideband power monitor |
Difference Frequency Generator |
|
|
|
for nonresonant sidebands |
Phase Frequency Discriminator |
1U |
|
|
for ALS |
RF Distribution Amplifier |
1U |
|
+-17V,+-24V |
split into 8 |
Delay Line Phase Shifter |
1U |
|
+15V? |
1 input, 1 output? |
Quad IQ Demodulator LSC |
1U |
+-18V |
4 LOs for 4 demodulation channels |
|
Quad IQ Demodulator ASC |
1U |
+-18V |
1 LO for 4 demodulation channels |
|
Common Mode Servo Board |
1U |
|
+-17V,+-24V |
2 inputs, slow and fast outputs |
PD Interface Board |
1U |
|
+-18V |
for ribbon cables from RF PDs. 8 inputs? |
QPD Interface Board |
1U |
|
+-18V? |
for ribbon cables from RF QPDs. 8 inputs? |
ISS Board |
? |
|
|
|
PLL Servo Board |
? |
|
|
|
OMC Servo Board |
? |
|
|
|
References: awiki/RfDesign, awiki/LSC_Photodetectors
Photodetector list
List of the Interferometer Detection Ports JGW-T1402982
For each rack
KAGRA ISC Electrical Components Layout JGW-D1402986
- In-vac PD/QPDs are not considered yet!!!
IO rack
Located between PSL and MCF chamber. Generates RF for fIMC, f1, f2, f3, 2*f1, 2*f2, f3-f1, f3-f2, fALSX, and fALSY. Has servo circuits for FRC, IMC, and ISS. Takes care of PD/QPDs on PSL, IMC REFL, IMC TRANS, IMMT1, and IMMT2 tables.
Name |
Height |
Description |
PD/QPD |
||
Quad IQ Demodulator LSC |
1U |
for IMCR(fIMC), IMMT2T(f1), IMMT2T(f2), (1ch left) |
PD Interface Board |
1Ux?? |
how many?? for PMCR, PMCT, REFCAVR, REFCAVT, IMCR, IMCT, IMMT1T, IMMT2T |
QPD Interface Board |
1Ux?? |
how many?? for IP_A/B, IMCR_A/B, IMCT_A/B, IMMT2T_A/B |
fIMC |
||
RF Oscillator Source |
? |
for fIMC sideband (also for Refcav) |
RF Distribution Amplifier |
1U |
for fIMC. to PSL EOM, to Delay Line for Refcav, to Delay Line for IMC LSC, to IQ Demod x 2, (3ch left) |
Delay Line Phase Shifter |
1U |
for TTFSS LO(Refcav lock) |
Delay Line Phase Shifter |
1U |
for CM board LO(IMC LSC) |
Common Mode Servo Board |
1U |
for IMC servo |
Quad IQ Demodulator ASC |
1U |
for IMCR_A QPD(fIMC) |
Quad IQ Demodulator ASC |
1U |
for IMCR_B QPD(fIMC) |
f1 |
||
RF Oscillator Source |
? |
for f1 sideband |
RF Distribution Amplifier |
1U |
for f1. to PSL EOM, to LSC racks, to Frequency Doubler, to Diff. Freq. Generator, to IMMT2T LO, (3ch left) |
Frequency Doubler |
1U |
f1 to 2*f1 for ISC racks |
f2 |
||
RF Oscillator Source |
? |
for f2 sideband |
RF Distribution Amplifier |
1U |
for f2. to PSL EOM, to LSC racks, to Frequency Doubler, to Diff. Freq. Generator, to IMMT2T LO, (3ch left) |
Frequency Doubler |
1U |
f1 to 2*f1 for ISC racks |
f3 |
||
RF Oscillator Source |
? |
for f3 to splitter |
(RF splitter) |
- |
split f3 into 2 for Diff. Freq. Generators |
Diff. Freq. Generator |
?? |
make f3-f1 for ISC racks |
Diff. Freq. Generator |
?? |
make f3-f2 for ISC racks |
fALSX,fALSY |
||
RF Oscillator Source |
? |
for fALSX sideband for ISC racks |
RF Oscillator Source |
? |
for fALSY sideband for ISC racks |
Others |
||
ISS Board |
?? |
|
ISC racks
Stands for LSC, ASC1, ASC2 and AUX racks located between PR3 and PR2 chambers. Has servo circuits for CARM, ALSX, and ALSY. Takes care of PD/QPDs on REFL, POP, POS, POX, POY, and AS tables.
Name |
Height |
Description |
PD/QPD |
||
Quad IQ Demodulator LSC |
1U |
for REFL(f1), REFL(f2), REFL_NRSB(f3-f1), REFL_NRSB(f3-f2) |
Quad IQ Demodulator LSC |
1U |
for POP(f1), POP(f2), SPOP(2*f1), SPOP(2*f2) |
Quad IQ Demodulator LSC |
1U |
for SPOS(2*f1), SPOS(2*f2), POP_GR(fALSY), POS_GR(fALSX) |
Quad IQ Demodulator LSC |
1U |
for POX(f1), POX(f2), POY(f1), POY(f2) |
Quad IQ Demodulator LSC |
1U |
for AS(f1), (3ch left) |
PD Interface Board |
1Ux?? |
how many?? for REFL, REFL_NRSB, POP, SPOP, SPOS, POX, POY, AS, OMCT, POP_GR, POS_GR |
QPD Interface Board |
1Ux?? |
how many?? for REFL_A/B, POP_A/B, AS_A/B, OMCT_A/B |
f1 |
||
RF Distribution Amplifier |
1U |
for f1. to Delay Line for CARM, POP LO, POX LO, POY LO, AS LO, (3ch left) |
Delay Line Phase Shifter |
1U |
for CM board LO(CARM) |
Common Mode Servo Board |
1U |
for CARM servo |
Quad IQ Demodulator ASC |
1U |
for REFL_A QPD(f1) |
Quad IQ Demodulator ASC |
1U |
for REFL_B QPD(f1) |
Quad IQ Demodulator ASC |
1U |
for POP_A QPD(f1) |
Quad IQ Demodulator ASC |
1U |
for POP_B QPD(f1) |
Quad IQ Demodulator ASC |
1U |
for AS_A QPD(f1) |
Quad IQ Demodulator ASC |
1U |
for AS_B QPD(f1) |
f2 |
||
RF Distribution Amplifier |
1U |
for f2. to REFL LO, POP LO, POX LO, POY LO, (4ch left) |
Quad IQ Demodulator ASC |
1U |
for REFL_A QPD(f2) |
Quad IQ Demodulator ASC |
1U |
for REFL_B QPD(f2) |
Quad IQ Demodulator ASC |
1U |
for POP_A QPD(f2) |
Quad IQ Demodulator ASC |
1U |
for POP_B QPD(f2) |
2*f1,2*f2 |
||
(RF splitter) |
- |
split 2*f1 into 2 for SPOP LO, SPOS LO |
(RF splitter) |
- |
split 2*f2 into 2 for SPOP LO, SPOS LO |
f3-f1,f3-f2 |
||
fALSX,fALSY |
||
(RF splitter) |
- |
split fALSX into 2 for POS EOM, Delay Line for ALSX |
Delay Line Phase Shifter |
1U |
for CM board LO(ALSX) |
Common Mode Servo Board |
1U |
for ALSX servo |
(RF splitter) |
- |
split fALSY into 2 for POP EOM, Delay Line for ALSY |
Delay Line Phase Shifter |
1U |
for CM board LO(ALSY) |
Common Mode Servo Board |
1U |
for ALSY servo |
PLL Servo Board |
? |
|
PLL Servo Board |
? |
|
EX4 rack
Located close to EXC chamber. Takes care of PD/QPDs on TRX table.
Name |
Height |
Description |
PD/QPD |
||
PD Interface Board |
1Ux?? |
how many?? for TRX, TRX_GR |
QPD Interface Board |
1Ux?? |
how many?? for TRX_A/B, TRX_GR_A/B |
EY4 rack
Located close to EYC chamber. Components should be the same as those in EX4.
Plan (as of 2012-08)
- Test fabrication of RF PD (by the end of September ?, test in October)
- Compile other analog circuit designs from LIGO into KAGRA spec. (by the end of October)
- Design frequency stabilization related circuits with NAOJ group (by the end of FY2012)