Differences between revisions 2 and 20 (spanning 18 versions)
⇤ ← Revision 2 as of 2022-10-26 09:02:28 →
Size: 1671
Editor: KeikoKokeyama
Comment:
← Revision 20 as of 2022-10-26 11:35:11 → ⇥
Size: 4578
Editor: KeikoKokeyama
Comment:
Deletions are marked like this. Additions are marked like this.
Line 1: Line 1:
= Angular Sensing and Control (2022) = = Angular Sensing and Control (Oct, 2022) =

<<TableOfContents()>>
Line 8: Line 10:
  * Same as O3GK
Line 9: Line 12:
 * Phasing is done by Kenta
Line 14: Line 18:
  * POP WFSs were newly installed after O3GK
Line 15: Line 20:
 * Phasing is done by Kenta
Line 19: Line 24:
  *   * https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=9817
  * Mostly same as O3GK
Line 23: Line 29:
 * Phasing is done by Kenta in June
Line 26: Line 33:

=== TMSX ===
 * There is only QPD2 ({{{K1:TMS-X_IR_QPDA2_{PIT,YAW} }}}) on the TMSX in-air path. At a random Gouy phase position.
 * The beam was sent to the QPD2 when the X-arm is locked, but the X-arm alignment may have changed since then.
 * TMSX in-air table power budget
  * https://klog.icrr.u-tokyo.ac.jp/osl/?r=22310
 * The in-air beam is extremely astigmatic
  * https://klog.icrr.u-tokyo.ac.jp/osl/?r=22221
 * There are strong PIT-YAW coupling depending on the position of the beam
  * https://klog.icrr.u-tokyo.ac.jp/osl/?r=22228
  * Matteo-san's previous measurement did not show a strong coupling. It seems to depend on the position of the DC QPDs.
   * https://klog.icrr.u-tokyo.ac.jp/osl/?r=20263
Line 28: Line 49:
 * QPD1 is used to the beam position control feeding back to the BS ({{{K1:ASC-DOF1_{P,Y} }}})
Line 33: Line 55:
=== TMSX ===
Line 37: Line 57:
  * {{{K1:ASC-POP_FORWARD_QPDA1_DC_{PIT,YAW} }}}
  * They can be found on sitemap > ASC overview > All DC QPDs

== DC PDs ==
 * There are POP_P and POP_S DC PDs on POP.
  * {{{K1:LSC-POP_S{P}POL_DC}}}
  * Can anyone add them on an MEDM screen somewhere?
Line 40: Line 67:
Line 41: Line 69:
 * Open the REFL shutter for REFL WFS ==== General ====
Line 43: Line 71:
  * PZTs and picomotors are available  * If the beam is off from the WFSs, use the picomotors first because the PZT ranges are not large
 * {{{K1:ASC-DC{5,6,7}_{P,Y} }}} are to be used for the WFS DC centering loops
==== REFL ====
 * Open the REFL shutter first for REFL WFS
 * {{{K1:ASC-DC5_{P,Y} }}} are used for the DC centering controls
  * FM filters:
   * Gains: null (gain of 0) and Gain(UGF40)
   * LPF: p1 (pole at 1 Hz)
   * Integrator: p0:z1 (pole at 0 Hz, zero at 1 Hz) - turn this on after the LPF
==== POP ====
 * DC control loop not implemented yet
==== AS ====
 * DC control loop not implemented yet
Line 50: Line 91:
 * Output matrix
  * {{{K1:ASC-DSOFT_{P,Y} }}} to IY
  * {{{K1:ASC-DHARD_{P,Y} }}} to EY
Line 52: Line 96:
  * DSOFT is IY, DHARD is EY
* Loops or noise haven't been characterized 		 * Loops or noise haven't been characterized
 * No offsets were necessary on the sensors
Line 65: Line 109:

= Next Steps =
== Infrastructure ==
 * Guardian implementation
  * DC centering loops on REFL, POP, and AS
  * Single Y, X arms, and PRMI guardstates for initial alignment
 * Add trigger for the main ASC switch ({{{K1:ASC-WFS_GAIN}}}) similarly to the IMC switch ({{{K1:IMC-WFS_GAIN}}})
== Simulation ==
 * Compare the measured sensing matrices against the simulation
  * Koyama-kun's simulation GUI tool is available on the workstations
   * sitemap > Commissioning Top > finesse GUI
== Integration ==
 * Implement single-Y, single-X, and PRMI controls for the initial alignment
  * If the alignment is too off, first ADS then WFS control?
 * PRFPMI/DRFPMI angular controls
 * Noise budget

= Known issues =
 * TMSX PIT-YAW coupling
  * The beam is slightly not centered in yaw on the second lens on the in-air table. Adjusting the beam position on the lens might fix the problem.

Angular Sensing and Control (Oct, 2022)

Contents

  1. Angular Sensing and Control (Oct, 2022)
    1. WFS ports
      1. REFL (17, 45 MHz)
      2. POP (17, 45 MHz)
      3. AS (17, 28 MHz)
    2. DC QPD ports
      1. TMSX
      2. TMSY
      3. POP Forward
    3. DC PDs
    4. WFS Commissioning
      1. WFS DC centering
        1. General
        2. REFL
        3. POP
        4. AS
      2. Single Y arm
      3. Single X arm
      4. PRMI
      5. PRFPMI
      6. DRFPMI
  2. Next Steps
    1. Infrastructure
    2. Simulation
    3. Integration
  3. Known issues

WFS ports

REFL (17, 45 MHz)

POP (17, 45 MHz)

AS (17, 28 MHz)

DC QPD ports

TMSX

TMSY

POP Forward

  • There are two DC QPDs on POP Forward, used for the initial alignment

    • K1:ASC-POP_FORWARD_QPDA1_DC_{PIT,YAW} 

    • They can be found on sitemap > ASC overview > All DC QPDs

DC PDs

  • There are POP_P and POP_S DC PDs on POP.

    • K1:LSC-POP_S{P}POL_DC

    • Can anyone add them on an MEDM screen somewhere?

WFS Commissioning

WFS DC centering

General

  • Beam spots on the quadrant diodes must be centered (DC centering)
  • If the beam is off from the WFSs, use the picomotors first because the PZT ranges are not large

  • K1:ASC-DC{5,6,7}_{P,Y}  are to be used for the WFS DC centering loops

REFL

  • Open the REFL shutter first for REFL WFS

  • K1:ASC-DC5_{P,Y}  are used for the DC centering controls

    • FM filters:
      • Gains: null (gain of 0) and Gain(UGF40)
      • LPF: p1 (pole at 1 Hz)
      • Integrator: p0:z1 (pole at 0 Hz, zero at 1 Hz) - turn this on after the LPF

POP

  • DC control loop not implemented yet

AS

  • DC control loop not implemented yet

Single Y arm

Single X arm

PRMI

PRFPMI

DRFPMI

Next Steps

Infrastructure

  • Guardian implementation
    • DC centering loops on REFL, POP, and AS
    • Single Y, X arms, and PRMI guardstates for initial alignment

  • Add trigger for the main ASC switch (K1:ASC-WFS_GAIN) similarly to the IMC switch (K1:IMC-WFS_GAIN)

Simulation

  • Compare the measured sensing matrices against the simulation
    • Koyama-kun's simulation GUI tool is available on the workstations

      • sitemap > Commissioning Top > finesse GUI

Integration

  • Implement single-Y, single-X, and PRMI controls for the initial alignment
    • If the alignment is too off, first ADS then WFS control?
  • PRFPMI/DRFPMI angular controls
  • Noise budget

Known issues

  • TMSX PIT-YAW coupling
    • The beam is slightly not centered in yaw on the second lens on the in-air table. Adjusting the beam position on the lens might fix the problem.

KAGRA/Subgroups/MIF/AngularSensing (last edited 2022-11-02 09:12:15 by KeikoKokeyama)