Differences between revisions 3 and 21 (spanning 18 versions)
⇤ ← Revision 3 as of 2022-10-26 10:26:08 →
Size: 2953
Editor: KeikoKokeyama
Comment:
← Revision 21 as of 2022-11-02 09:12:15 → ⇥
Size: 4685
Editor: KeikoKokeyama
Comment:
Deletions are marked like this. Additions are marked like this.
Line 1: Line 1:
= Angular Sensing and Control (2022) = = Angular Sensing and Control (Oct, 2022) =
Line 12: Line 12:
 * Phasing is done by Kenta
Line 19: Line 20:
 * Phasing is done by Kenta
Line 28: Line 29:
 * Phasing is done by Kenta in June
Line 31: Line 33:

=== TMSX ===
 * There is only QPD2 ({{{K1:TMS-X_IR_QPDA2_{PIT,YAW} }}}) on the TMSX in-air path. At a random Gouy phase position.
 * The beam was sent to the QPD2 when the X-arm is locked, but the X-arm alignment may have changed since then.
 * TMSX in-air table power budget
  * https://klog.icrr.u-tokyo.ac.jp/osl/?r=22310
 * The in-air beam is extremely astigmatic
  * https://klog.icrr.u-tokyo.ac.jp/osl/?r=22221
 * There are strong PIT-YAW coupling depending on the position of the beam
  * https://klog.icrr.u-tokyo.ac.jp/osl/?r=22228
  * Matteo-san's previous measurement did not show a strong coupling. It seems to depend on the position of the DC QPDs.
   * https://klog.icrr.u-tokyo.ac.jp/osl/?r=20263
  * Is the TMSX in-air beam clipped in the TMS in-vac?
   * https://klog.icrr.u-tokyo.ac.jp/osl/?r=22762
Line 33: Line 51:
 * QPD1 is used to steer the beam from BS (ASC DOF1 is the TMSY QPD loop feeding back to the BS)  * QPD1 is used to the beam position control feeding back to the BS ({{{K1:ASC-DOF1_{P,Y} }}})
Line 39: Line 57:
=== TMSX ===
 * There is only one DC QPD installed on the TMSX in-air path
 * The beam is NOT centered on the DC QPD when the X-arm is locked
 * TMSX in-air table power budget
  * https://klog.icrr.u-tokyo.ac.jp/osl/?r=22310
 * The in-air beam is extremely astigmatic
  *
 * There are strong PIT-YAW coupling depending on the position of the beam
  * https://klog.icrr.u-tokyo.ac.jp/osl/?r=22545
Line 51: Line 59:
  * {{{K1:ASC-POP_FORWARD_QPDA1_DC_{PIT,YAW} }}}
  * They can be found on sitemap > ASC overview > All DC QPDs
Line 54: Line 64:
  * {{{K1:LSC-POP_S{P}POL_DC}}}
  * Can anyone add them on an MEDM screen somewhere?
Line 59: Line 71:
 * Open the REFL shutter for REFL WFS ==== General ====
Line 61: Line 73:
  * PZTs and picomotors are available  * If the beam is off from the WFSs, use the picomotors first because the PZT ranges are not large
 * {{{K1:ASC-DC{5,6,7}_{P,Y} }}} are to be used for the WFS DC centering loops
==== REFL ====
 * Open the REFL shutter first for REFL WFS
 * {{{K1:ASC-DC5_{P,Y} }}} are used for the DC centering controls
  * FM filters:
   * Gains: null (gain of 0) and Gain(UGF40)
   * LPF: p1 (pole at 1 Hz)
   * Integrator: p0:z1 (pole at 0 Hz, zero at 1 Hz) - turn this on after the LPF
==== POP ====
 * DC control loop not implemented yet
==== AS ====
 * DC control loop not implemented yet
Line 68: Line 93:
 * Output matrix
  * {{{K1:ASC-DSOFT_{P,Y} }}} to IY
  * {{{K1:ASC-DHARD_{P,Y} }}} to EY
Line 70: Line 98:
  * DSOFT is IY, DHARD is EY
* Loops or noise haven't been characterized 		 * Loops or noise haven't been characterized
 * No offsets were necessary on the sensors
Line 85: Line 113:
== Infrastructure ==
Line 86: Line 115:
 * Add trigger for the main ASC switch (K1:ASC-WFS_GAIN) similarly to the IMC switch (K1:IMC-WFS_GAIN)   * DC centering loops on REFL, POP, and AS
  * Single Y, X arms, and PRMI guardstates for initial alignment
 * Add trigger for the main ASC switch ({{{K1:ASC-WFS_GAIN}}}) similarly to the IMC switch ({{{K1:IMC-WFS_GAIN}}})
== Simulation ==
 * Compare the measured sensing matrices against the simulation
  * Koyama-kun's simulation GUI tool is available on the workstations
   * sitemap > Commissioning Top > finesse GUI
== Integration ==

Angular Sensing and Control (Oct, 2022)

Contents

  1. Angular Sensing and Control (Oct, 2022)
    1. WFS ports
      1. REFL (17, 45 MHz)
      2. POP (17, 45 MHz)
      3. AS (17, 28 MHz)
    2. DC QPD ports
      1. TMSX
      2. TMSY
      3. POP Forward
    3. DC PDs
    4. WFS Commissioning
      1. WFS DC centering
        1. General
        2. REFL
        3. POP
        4. AS
      2. Single Y arm
      3. Single X arm
      4. PRMI
      5. PRFPMI
      6. DRFPMI
  2. Next Steps
    1. Infrastructure
    2. Simulation
    3. Integration
  3. Known issues

WFS ports

REFL (17, 45 MHz)

POP (17, 45 MHz)

AS (17, 28 MHz)

DC QPD ports

TMSX

TMSY

POP Forward

  • There are two DC QPDs on POP Forward, used for the initial alignment

    • K1:ASC-POP_FORWARD_QPDA1_DC_{PIT,YAW} 

    • They can be found on sitemap > ASC overview > All DC QPDs

DC PDs

  • There are POP_P and POP_S DC PDs on POP.

    • K1:LSC-POP_S{P}POL_DC

    • Can anyone add them on an MEDM screen somewhere?

WFS Commissioning

WFS DC centering

General

  • Beam spots on the quadrant diodes must be centered (DC centering)
  • If the beam is off from the WFSs, use the picomotors first because the PZT ranges are not large

  • K1:ASC-DC{5,6,7}_{P,Y}  are to be used for the WFS DC centering loops

REFL

  • Open the REFL shutter first for REFL WFS

  • K1:ASC-DC5_{P,Y}  are used for the DC centering controls

    • FM filters:
      • Gains: null (gain of 0) and Gain(UGF40)
      • LPF: p1 (pole at 1 Hz)
      • Integrator: p0:z1 (pole at 0 Hz, zero at 1 Hz) - turn this on after the LPF

POP

  • DC control loop not implemented yet

AS

  • DC control loop not implemented yet

Single Y arm

Single X arm

PRMI

PRFPMI

DRFPMI

Next Steps

Infrastructure

  • Guardian implementation
    • DC centering loops on REFL, POP, and AS
    • Single Y, X arms, and PRMI guardstates for initial alignment

  • Add trigger for the main ASC switch (K1:ASC-WFS_GAIN) similarly to the IMC switch (K1:IMC-WFS_GAIN)

Simulation

  • Compare the measured sensing matrices against the simulation
    • Koyama-kun's simulation GUI tool is available on the workstations

      • sitemap > Commissioning Top > finesse GUI

Integration

  • Implement single-Y, single-X, and PRMI controls for the initial alignment
    • If the alignment is too off, first ADS then WFS control?
  • PRFPMI/DRFPMI angular controls
  • Noise budget

Known issues

  • TMSX PIT-YAW coupling
    • The beam is slightly not centered in yaw on the second lens on the in-air table. Adjusting the beam position on the lens might fix the problem.

KAGRA/Subgroups/MIF/AngularSensing (last edited 2022-11-02 09:12:15 by KeikoKokeyama)