|
Size: 1456
Comment:
|
← Revision 5 as of 2016-03-03 01:20:48 ⇥
Size: 2486
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 2: | Line 2: |
| Date: 2016/3/3 | |
| Line 3: | Line 4: |
Date: 2016/3/3 Workers: Michimura,Ushiba,Furuhata,Kambara, Aso |
Workers: Aso, Michimura, Ushiba, Kuwahara, Okutomi, Furuhata |
| Line 13: | Line 12: |
| * Setup COACH filters near the PR3 chamber * Setup COACH filters near the PR2 chamber |
* Setup KOACH filters near the PR3 chamber * Setup KOACH filters near the PR2 chamber |
| Line 21: | Line 20: |
| * Declare the laser hazard area. Distribute laser goggles to people in the center area | * Declare the laser hazard area. Distribute laser goggles to people in the center area |
| Line 23: | Line 22: |
| * Measure the beam profile in front of PR2 using the middle size beam profiler | * Measure the beam profile in front of PR2 using the middle size beam profiler |
| Line 26: | Line 25: |
| * Declare the finish of the laser hazard | * Declare the finish of the laser hazard |
| Line 28: | Line 27: |
| * Stop COACH filters | * Cleaning around the chambers * Stop KOACH filters |
| Line 31: | Line 31: |
| * Middle size beam profiler (check with Doi-san) | * Middle size beam profiler (Found one near the MCF clean booth. Check with Doi-san) |
| Line 33: | Line 33: |
| * Large size beam profiler (need to find where) * A height adjustable table (check with Saito-san) * Two PHS phones for communication between PR and BS area clean booths (or transceivers) |
* Large size beam profiler (Doi-san's room) * A height adjustable table (Found two of them near the PR3 on +Y side) * Two PHS phones for communication between PR and BS area clean booths (or transceivers) * Two sets of floor KOACH * Clean suits and inner ware * Chamber compatible type * Found many L and M in the laser room. For other size, we need to bring them from the data analysis building. * A wrench to turn the bolts for the flanges (in the red tool cabinet near PR2 clean booth) * A PC (or two) for controlling the picomotor (will use one of the DGS mac books) * Prepare a joypad as a backup (Found one in the PR2 clean booth) * A lot of laser goggles (In a cardboard box near the entrance to PR3 clean booth) * Sensor cards (check with IOO people) * IR viewer (Found two near the MCF chamber. Check with IOO people) === Items to be brought into the tunnel === * Large beam profiler * Clean suits (except for L and LL) * PHS (2) === Notes === * Divide the team of 5 into 2-2-1 (PR area - BS area - outside the clean booths) * Who will operate the MC: Enomoto-kun will be in Kamioka this week. |
iKAGRA PR2 alignment & Beam Profile Measurements
Date: 2016/3/3
Workers: Aso, Michimura, Ushiba, Kuwahara, Okutomi, Furuhata
Objectives
- Center the beams on PR2 and PR3 mirrors
- Measure the beam profile in front of PR2 and PR3
Procedure
- Enter the tunnel, check necessary tools
- Setup KOACH filters near the PR3 chamber
- Setup KOACH filters near the PR2 chamber
- Open the flange of PR3 (on the +X side)
- Open the flange of PR2 (both -X and +X sides)
Lock the MC and send the beam from IMMT2 to PR2 with low power (<2mW)
- Center the beam on PR2 using IMMT2 picomotors
- Center the beam on PR3 using PR3 picomotors
- If the beam on PR3 is too dim and difficult to align
- Declare the laser hazard area. Distribute laser goggles to people in the center area
- Increase the power from MC (to 25mW or so)
- Measure the beam profile in front of PR2 using the middle size beam profiler
- Measure the beam profile in front of PR3 using the large beam profiler
- Stop the beam from MC
- Declare the finish of the laser hazard
- Close the flanges
- Cleaning around the chambers
- Stop KOACH filters
Necessary items, tools
- Middle size beam profiler (Found one near the MCF clean booth. Check with Doi-san)
- A stand to hold it at the right height
- Large size beam profiler (Doi-san's room)
- A height adjustable table (Found two of them near the PR3 on +Y side)
- Two PHS phones for communication between PR and BS area clean booths (or transceivers)
- Two sets of floor KOACH
- Clean suits and inner ware
- Chamber compatible type
- Found many L and M in the laser room. For other size, we need to bring them from the data analysis building.
- A wrench to turn the bolts for the flanges (in the red tool cabinet near PR2 clean booth)
- A PC (or two) for controlling the picomotor (will use one of the DGS mac books)
- Prepare a joypad as a backup (Found one in the PR2 clean booth)
- A lot of laser goggles (In a cardboard box near the entrance to PR3 clean booth)
- Sensor cards (check with IOO people)
- IR viewer (Found two near the MCF chamber. Check with IOO people)
Items to be brought into the tunnel
- Large beam profiler
- Clean suits (except for L and LL)
- PHS (2)
Notes
- Divide the team of 5 into 2-2-1 (PR area - BS area - outside the clean booths)
- Who will operate the MC: Enomoto-kun will be in Kamioka this week.