Differences between revisions 1 and 220 (spanning 219 versions)
⇤ ← Revision 1 as of 2018-07-25 08:20:33 →
Size: 20
Editor: TakaakiYokozawa
Comment:
← Revision 220 as of 2018-12-27 12:14:20 → ⇥
Size: 15370
Editor: KousekiMiyo
Comment:
Deletions are marked like this. Additions are marked like this.
Line 1: Line 1:
KAGRA PEM Channels <<TableOfContents(3)>>
= KAGRA PEM Channel List =


== Ondotori ==
 * [[KAGRA/Subgroups/DGS/Projects/Rem|Ondotori System]]

== PSL(-2018/12/10-) ==
|| PEM || Sensor || Channel name (_OUT_DQ) || sampling rate[Hz] ||Picture || Calibration(unit) || Memo(S number) ||
|| accelerometer || TEAC 710 || K1:PEM-PSL_ACC_TABLE1_Z || 2048 || [[attachment:PEM_pic_ACC_TEAC_table1.pdf|pic]] || m/s^2 || [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=8520|ACC]], [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=8523|Amp]] ||
|| accelerometer || TEAC 710 || K1:PEM-PSL_ACC_TABLE2_Z || 2048 || [[attachment:PEM_pic_ACC_TEAC_table2.pdf|pic]] || m/s^2 || [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=8521|ACC]], [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=8524|Amp]] ||
|| accelerometer || TEAC 710 || K1:PEM-PSL_ACC_TABLE3_Z || 2048 || [[attachment:PEM_pic_ACC_TEAÇ_table3.pdf|pic]] || m/s^2 || [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=8522|ACC]], [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=8525|Amp]] ||
|| accelerometer || KISTLER 8640A5 || K1:PEM-PSL_ACC_PERI_EXIT || 2048 || [[attachment:PEM_pic_ACC_KISTLER_exit.pdf|pic]] || m/s^2 || [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7226|ACC]], [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=8193|Amp]]||
|| accelerometer || KISTLER 8640A5 || K1:PEM-PSL_ACC_PERI_REFCAV || 2048 || [[attachment:PEM_pic_ACC_KISTLER_refcav.pdf|pic]] || m/s^2 || [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7225|ACC]], [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=8191|Amp]] ||
|| --( magnetometer)-- || MAG13 MCL100 || --( K1:PEM-PSL_MAG_LASERRACK_(X|Y|Z) )-- || --( 2048 )-- || [[attachment:PEM_pic_MAG_pslrack.pdf|pic]] || T || [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7535|MAG13]], [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=8181|WF]], [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=8519|Distributor]], [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=8518|Power]] removed temporary||
|| microphone || (B&K) 4188-A-021 || K1:PEM-PSL_MIC_CENTER || 2048 || [[attachment:PEM_pic_MIC_center.pdf|pic]] || Pa || [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=8142|MIC]], [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=8142|amp]]||
|| accelerometer || KISTLER || K1:PEM-PSL_ACC_SIGNAL1 || 2048 || [[attachment:PEM_pic_ACC_SIGNAL12.pdf|pic]] || m/s^2 || [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7223|ACC]], [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=8189|Amp]], portable accelerometer ||
|| accelerometer || KISTLER || K1:PEM-PSL_ACC_SIGNAL2 || 2048 || [[attachment:PEM_pic_ACC_SIGNAL12.pdf|pic]] || m/s^2 || [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7224|ACC]], [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=8195|Amp]], portable accelerometer||

== CS(-2018/12/10-) ==
|| PEM || Sensor || Channel name (_OUT_DQ) || sampling rate[Hz || Picture || Calibration(unit) || Memo(S number) ||
|| microphone || AT-VD6 No.1 || K1:PEM-IMC_MIC_REFL||2048 || [[attachment:PEM_pic_MIC_IMC_refl.pdf|pic]] || Pa || [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7647|MIC]], [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=9068|amp]]||
|| accelerometer || TEAC706 || K1:PEM-IMC_ACC_REFL_TABLE || 2048 || [[attachment:PEM_pic_ACC_IMC_refl.pdf|pic]] || m/s^2 || [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=9062|ACC]], [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7649|amp]]||
|| microphone || AT-VD6 No.2 || K1:PEM-IMC_MIC_TRANS|| 2048 || [[|pic]] || Pa || [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7648|MIC]], [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7650|amp]]||
|| microphone || (B&K) 4188-A-021 || K1:PEM-IFI_MIC_REFL || 2048 || [[attachment:PEM_pic_ACC_MIC_IFI.pdf|pic]] || Pa || [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=8974|MIC]], [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=8975|amp]]||
|| accelerometer || TEAC710 || K1:PEM-IFI_ACC_REFL_TABLE || 2048 || [[attachment:PEM_pic_ACC_MIC_IFI.pdf|pic]] || m/s^2 || [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=9328|ACC]], [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=9332|amp]]||
|| microphone || (B&K) 4188-A-021 || K1:PEM-POP_MIC || 2048 || [[attachment:PEM_pic_ACC_MIC_POP.pdf|pic]] || Pa || [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=8976|MIC]], [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=8975|amp]]||
|| accelerometer || TEAC710 || K1:PEM-POP_ACC_TABLE || 2048 || [[attachment:PEM_pic_ACC_MIC_POP.pdf|pic]] || m/s^2 || [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=9326|ACC]], [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=9330|amp]]||
|| microphone || ACO 7146NL/4152 || K1:PEM-POS_MIC || 2048 || [[attachment:PEM_pic_MIC_POS.pdf|pic]] || Pa || [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=9036|MIC]], [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=9317|amp]]||
|| accelerometer || TEAC710 || K1:PEM-POS_ACC_TABLE || 2048 || [[attachment:PEM_pic_ACC_POS.pdf|pic]] || m/s^2 || [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=9325|ACC]], [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=9329|amp]]||
|| microphone || ACO 7146/4152 || K1:PEM-OMC_MIC || 2048 || [[attachment:PEM_pic_MIC_OMC.pdf|pic]] || Pa || [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=9035|MIC]], [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=9317|amp]]||
|| accelerometer || TEAC710 || K1:PEM-OMC_ACC_TABLE || 2048 || [[attachment:PEM_pic_ACC_TEAC_OMC.pdf|pic]] || m/s^2 || [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=9327|ACC]], [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=9331|amp]]||
|| microphone || ACO 7146/4152 || K1:PEM-BS_MIC || 2048 || [[attachment:PEM_pic_MIC_BS.pdf|pic]] || Pa || [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=9034|MIC]], [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=9317|amp]]||
|| microphone || ACO 7146/4152 || K1:PEM-SR_MIC || 2048 || [[attachment:PEM_pic_MIC_SR.pdf|pic]] || Pa || [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=9038|MIC]], [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=9317|amp]]||

== EX(-201X/XX/XX) ==
 * PCal Tx table (TEAC710)
 * PCal Rx table (TEAC710)
 * EXA area (ACO mic)
 * EXC/EXV area (ACO mic)
 * EXV talbe (TEAC706)
 * EXC area (magnetometer)

== EY(-201X/XX/XX) ==
 * PCal Tx table (TEAC710)
 * PCal Rx table (TEAC710)
 * EYA area (ACO mic)
 * EYC/EYV area (ACO mic)
 * EYV talbe (TEAC706)
 * EYC area (magnetometer)


== Seismometer ==
||<#F0F0FF> Snumber ||<#F0F0FF>Installed Place (ADC port) ||<#F0F0FF> Name ||<#F0F0FF> Channel name (OUT_DQ) ||<#F0F0FF> Unit ||<#F0F0FF> fs [Hz] ||<#F0F0FF> klog ||
||[[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7552|JGW-S1707552]] || EXV (IX1, ADC0, 24-26) || Trillium 12QA || K1:PEM-IXV_GND_TR120Q_(X/Y/Z)_OUT_DQ || um/s || 512|| [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=7186|7186]] ||
||[[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7551|JGW-S1707551]] || EXV (EX1, ADC0, 24-26) || Trillium 120QA || K1:PEM-EXV_GND_TR120Q_(X/Y/Z)_OUT_DQ || um/s || 512 || [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=7186|7186]] ||
||--([[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7553|JGW-S1707553]])-- || --(EYV (EY1, ADC0, 24-26) )-- || --(Trillium 120QA)-- || --(K1:PEM-EYV_GND_TR120Q_(X/Y/Z)_OUT_DQ)-- || --(um/s)-- || 512 || [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=7186|7186]] ||
||[[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7553|JGW-S1707553]] || IXV (IX1, ADC0, 28-30) || Trillium 120QA|| K1:PEM-IXV_GND_TR120QTEST_(X/Y/Z)_OUT_DQ || um/s || 512 || [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=7186|7186]] ||
|| [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=xxxx|JGW-S170xxxx]] || MCe (IOO1, ADC1, 4-6) || Trillium compact 120-SV1 || K1:PEM-IMC_GND_TR120C_MCE_(X/Y/Z)_OUT_DQ || um/s || 512 || ||
|| [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=xxxx|JGW-S170xxxx]] || MCi (IOO1, ADC1, 0-2) || Trillium compact 120-SV1|| K1:PEM-IMC_GND_TR120C_MCI_(X/Y/Z)_OUT_DQ || um/s || 512 || ||
|| [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7528|JGW-S1707528]] || Fukuoka Univ. || Trillium compact 120-SV1|| ??? || --- || 512|| ||
{*} Selfnoiseのグラフを載せる

== Air Environment Sensors ==
||<#F0F0FF> Snumber ||<#F0F0FF>Installed Place (ADC port) ||<#F0F0FF> Name ||<#F0F0FF> Channel name (xxx_OUT_DQ) ||<#F0F0FF> Unit ||<#F0F0FF> Sample rate [Hz] ||
||[[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=9339|JGW-S1709339]] ||IXV (IX1, ADC1, 24-27) || No.5|| K1-IXV_WEATHER_{TEMP,HUMD,PRES}_|| Degree, %, Pa || 128 ||
||[[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=xxxx|JGW-S170XXX]] ||IYV (IY1, ADC1, 24-27) || || || || 128 ||
||[[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=xxxx|JGW-S170xxxx]] ||EXV (EX1, ADC1, 24-27) || ---|| K1-EXV_WEATHER_{TEMP,HUMD,PRES}_|| Degree, %, Pa || 128 ||
||[[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=xxxx|JGW-S170xxxx]] ||EYV (EY1, ADC1, 24-27) ||---|| K1-EYV_WEATHER_{TEMP,HUMD,PRES}_|| Degree, %, Pa || 128 ||
||[[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=xxxx|JGW-S170xxxx]] || IXC (IX0, ADC0, 16-27?) || || || || 128 ||
||[[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=9340|JGW-S1709340]] || IYC (IY0, ADC0, 20-23) || No6 || K1-IYC_WEATHER_{TEMP,HUMD,PRES}_|| Degree, %, Pa || 128 ||
Acording to [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=9269|JGW-T1809269]], calibration factor from output voltage to each unit is given with
{{{
temp = ( Vout/78/0.001-100)/0.388 [deg_c]
humd = (Vout/2)/5*100 [%]
pressure = (Vout/2)/5*300 + 800 [hPa]
}}}
Then, "_GAIN" and "_OFFSET" parameters in cds filter of each channels are calculated by above equation with count value not voltage,
||<#F0F0FF> Name ||<#F0F0FF> Value ||<#F0F0FF> Unit ||
|| _TEMP_OFFSET || -1.278e4|| count ||
|| _HUMD_OFFSET || 0.0|| count ||
|| _PRES_OFFSET || 4.369e4 || count ||
|| _TEMP_GAIN || 2.017e-2|| deg_c/count||
|| _HUMD_GAIN || 6.104e-3|| %/count ||
|| _PRES_GAIN || 1.831e-2 || hPa/count ||
,where ransformation coefficient from voltage to adc count is given with c2V = 2.0 * 10/2**15 [V/count], because output signal from sensor is measured with single-end not differential.
These parameters are '''managed by SDF with observe.snap. So, plase do not change this file.

== Temporary channels in IX0 ==
|| Place || Sensor || Channel name || picture || Memo ||
|| IX0 || Temporary || K1:PEM-IX0_SENSOR(1-12) || pic || Will be removed ||

== Temporary channels in IY0 ==
|| Place || Sensor || Channel name || picture || Memo ||
|| IY0 || Temporary || K1:PEM-IY0_SENSOR(1-12) || pic || Will be removed ||

= Channel Name Definition =
Definition of the PEM channel name

{{{
K1:PEM-(SENSOR)_(PLACE1)_(PLACE2)_(DOF)
}}}

== SENSOR ==
{{{
センサーの種類がここに該当する。
}}}

||<#FBEFF8> Name ||<#FBEFF8> Purpose ||
|| ONDTR || Ondotori sensor ||
|| ACC || Accelerometer ||
|| MIC || Microphone ||
|| MAG || Magnetometer ||
|| SEIS || Seismometer ||
|| WEATHER || Weather station ||
|| SENSOR(or SIGNAL; すぐに決めてどちらかにする) || -- ||

Comment

 * 現状(2018/12/26)は以上だが、今後PEMが足されるにつれて追加する。(yokozawa)

== PLACE1 ==
{{{
広い意味のエリア名が該当する？
}}}
||<#FBEFF8> Name ||<#FBEFF8> Purpose ||
|| PSL|| in the PSL Room area ||
|| IX || around the IX area ||
|| IY || around the IY area ||
|| EX || around the EX area ||
|| EY || around the EY area ||
|| IXV || in the IXV area ||
|| IYV || in the IYV area ||
|| EXV || in the EXV area ||
|| EYV || in the EYV area ||
|| TMSX || around the TMSX area ||
|| TMSY || around the TMSY area ||
|| PCALX || around the PCALX area ||
|| PCALY || around the PCALY area ||
|| PR|| around the PR area including chamber||
|| BS|| around the BS area including chamber||
|| SR|| around the SR area including chamber||
|| IMC|| around the MCi, MCe, MCo area||
|| IFI|| around the IFI area including table, chamber ||
|| OMC|| around the OMC area including table, chamber ||
|| POP|| around the POP area including table, chamber ||
|| POS|| around the POS area including talbe, chamber ||
|| RACK || in the DGS Rack ||
|| FIELD || on the field||
|| BOOTH|| in the "any" clean booth ||
|| MOZUMI|| in the mozumi building ||

Comment

  * (A chamberを加えるかどうかは議論が必要だが、今の所置く余裕がない)

== PLACE2 ==
{{{
センサーが設置されている構造物の名前が該当する？
}}}
||<#FBEFF8> Name ||<#FBEFF8> Purpose ||
|| GND || on the ground ||
|| PRERI || on the periscope ||
|| CHAMBER || on the chamber ||
|| BEAMDUCT || on the beamduct ||
|| TABLE || on the table ||
|| ONTABLE || Microphone on the table??? ||

Comment

 * もし該当しない場合、PLACE2を省略して、DOFに行ってもいいのだろうか。　(Miyo)

== DOF ==
{{{
DOFが該当する。センサーが複数個のシグナルを持つ場合、それぞれの名前が該当する？
}}}
||<#FBEFF8> Name ||<#FBEFF8> Purpose ||
|| X/Y/Z || X,Y,Z axis as KAGRA cordinate ||
|| 18V/24V || type of the DC power supply ||
|| TEMPERATURE/HUMIDITY/PRESSSURE || signals of the both ondotori and weather station ||

= SDF =
== latest snapfile ==
2018/12/03 Update, miyo
||<#F0F00F> Model ||<#F0F00F> snapfile ||<#F0F00F> Managed date ||<#F0F00F> klog ||
|| k1pemiy0 || observe.snap || Dec 03 09:49:41 2018 || [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=7249|7249]] ||
|| k1pemix1 || observe.snap || Nov 28 19:27:27 2018 || [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=7249|7249]] ||
|| k1pemex1 || observe.snap || Nov 28 19:25:46 2018 || [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=7249|7249]] ||
|| k1pemey1 || observe.snap || Nov 30 17:15:59 2018 || [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=7249|7249]] ||

Contents

  1. KAGRA PEM Channel List
    1. Ondotori
    2. PSL(-2018/12/10-)
    3. CS(-2018/12/10-)
    4. EX(-201X/XX/XX)
    5. EY(-201X/XX/XX)
    6. Seismometer
    7. Air Environment Sensors
    8. Temporary channels in IX0
    9. Temporary channels in IY0
  2. Channel Name Definition
    1. SENSOR
    2. PLACE1
    3. PLACE2
    4. DOF
  3. SDF
    1. latest snapfile

KAGRA PEM Channel List

Ondotori

PSL(-2018/12/10-)

PEM

Sensor

Channel name (_OUT_DQ)

sampling rate[Hz]

Picture

Calibration(unit)

Memo(S number)

accelerometer

TEAC 710

K1:PEM-PSL_ACC_TABLE1_Z

2048

pic

m/s^2

ACC, Amp

accelerometer

TEAC 710

K1:PEM-PSL_ACC_TABLE2_Z

2048

pic

m/s^2

ACC, Amp

accelerometer

TEAC 710

K1:PEM-PSL_ACC_TABLE3_Z

2048

pic

m/s^2

ACC, Amp

accelerometer

KISTLER 8640A5

K1:PEM-PSL_ACC_PERI_EXIT

2048

pic

m/s^2

ACC, Amp

accelerometer

KISTLER 8640A5

K1:PEM-PSL_ACC_PERI_REFCAV

2048

pic

m/s^2

ACC, Amp

magnetometer

MAG13 MCL100

K1:PEM-PSL_MAG_LASERRACK_(X|Y|Z)

2048

pic

T

MAG13, WF, Distributor, Power removed temporary

microphone

(B&K) 4188-A-021

K1:PEM-PSL_MIC_CENTER

2048

pic

Pa

MIC, amp

accelerometer

KISTLER

K1:PEM-PSL_ACC_SIGNAL1

2048

pic

m/s^2

ACC, Amp, portable accelerometer

accelerometer

KISTLER

K1:PEM-PSL_ACC_SIGNAL2

2048

pic

m/s^2

ACC, Amp, portable accelerometer

CS(-2018/12/10-)

PEM

Sensor

Channel name (_OUT_DQ)

sampling rate[Hz

Picture

Calibration(unit)

Memo(S number)

microphone

AT-VD6 No.1

K1:PEM-IMC_MIC_REFL

2048

pic

Pa

MIC, amp

accelerometer

TEAC706

K1:PEM-IMC_ACC_REFL_TABLE

2048

pic

m/s^2

ACC, amp

microphone

AT-VD6 No.2

K1:PEM-IMC_MIC_TRANS

2048

[[|pic]]

Pa

MIC, amp

microphone

(B&K) 4188-A-021

K1:PEM-IFI_MIC_REFL

2048

pic

Pa

MIC, amp

accelerometer

TEAC710

K1:PEM-IFI_ACC_REFL_TABLE

2048

pic

m/s^2

ACC, amp

microphone

(B&K) 4188-A-021

K1:PEM-POP_MIC

2048

pic

Pa

MIC, amp

accelerometer

TEAC710

K1:PEM-POP_ACC_TABLE

2048

pic

m/s^2

ACC, amp

microphone

ACO 7146NL/4152

K1:PEM-POS_MIC

2048

pic

Pa

MIC, amp

accelerometer

TEAC710

K1:PEM-POS_ACC_TABLE

2048

pic

m/s^2

ACC, amp

microphone

ACO 7146/4152

K1:PEM-OMC_MIC

2048

pic

Pa

MIC, amp

accelerometer

TEAC710

K1:PEM-OMC_ACC_TABLE

2048

pic

m/s^2

ACC, amp

microphone

ACO 7146/4152

K1:PEM-BS_MIC

2048

pic

Pa

MIC, amp

microphone

ACO 7146/4152

K1:PEM-SR_MIC

2048

pic

Pa

MIC, amp

EX(-201X/XX/XX)

  • PCal Tx table (TEAC710)
  • PCal Rx table (TEAC710)
  • EXA area (ACO mic)
  • EXC/EXV area (ACO mic)
  • EXV talbe (TEAC706)
  • EXC area (magnetometer)

EY(-201X/XX/XX)

  • PCal Tx table (TEAC710)
  • PCal Rx table (TEAC710)
  • EYA area (ACO mic)
  • EYC/EYV area (ACO mic)
  • EYV talbe (TEAC706)
  • EYC area (magnetometer)

Seismometer

Snumber

Installed Place (ADC port)

Name

Channel name (OUT_DQ)

Unit

fs [Hz]

klog

JGW-S1707552

EXV (IX1, ADC0, 24-26)

Trillium 12QA

K1:PEM-IXV_GND_TR120Q_(X/Y/Z)_OUT_DQ

um/s

512

7186

JGW-S1707551

EXV (EX1, ADC0, 24-26)

Trillium 120QA

K1:PEM-EXV_GND_TR120Q_(X/Y/Z)_OUT_DQ

um/s

512

7186

JGW-S1707553

EYV (EY1, ADC0, 24-26)

Trillium 120QA

K1:PEM-EYV_GND_TR120Q_(X/Y/Z)_OUT_DQ

um/s

512

7186

JGW-S1707553

IXV (IX1, ADC0, 28-30)

Trillium 120QA

K1:PEM-IXV_GND_TR120QTEST_(X/Y/Z)_OUT_DQ

um/s

512

7186

JGW-S170xxxx

MCe (IOO1, ADC1, 4-6)

Trillium compact 120-SV1

K1:PEM-IMC_GND_TR120C_MCE_(X/Y/Z)_OUT_DQ

um/s

512

JGW-S170xxxx

MCi (IOO1, ADC1, 0-2)

Trillium compact 120-SV1

K1:PEM-IMC_GND_TR120C_MCI_(X/Y/Z)_OUT_DQ

um/s

512

JGW-S1707528

Fukuoka Univ.

Trillium compact 120-SV1

???

---

512

{*} Selfnoiseのグラフを載せる

Air Environment Sensors

Snumber

Installed Place (ADC port)

Name

Channel name (xxx_OUT_DQ)

Unit

Sample rate [Hz]

JGW-S1709339

IXV (IX1, ADC1, 24-27)

No.5

K1-IXV_WEATHER_{TEMP,HUMD,PRES}_

Degree, %, Pa

128

JGW-S170XXX

IYV (IY1, ADC1, 24-27)

128

JGW-S170xxxx

EXV (EX1, ADC1, 24-27)

---

K1-EXV_WEATHER_{TEMP,HUMD,PRES}_

Degree, %, Pa

128

JGW-S170xxxx

EYV (EY1, ADC1, 24-27)

---

K1-EYV_WEATHER_{TEMP,HUMD,PRES}_

Degree, %, Pa

128

JGW-S170xxxx

IXC (IX0, ADC0, 16-27?)

128

JGW-S1709340

IYC (IY0, ADC0, 20-23)

No6

K1-IYC_WEATHER_{TEMP,HUMD,PRES}_

Degree, %, Pa

128

Acording to JGW-T1809269, calibration factor from output voltage to each unit is given with 

temp = ( Vout/78/0.001-100)/0.388  [deg_c]
humd = (Vout/2)/5*100 [%]
pressure = (Vout/2)/5*300 + 800 [hPa]

Then, "_GAIN" and "_OFFSET" parameters in cds filter of each channels are calculated by above equation with count value not voltage,

Name

Value

Unit

_TEMP_OFFSET

-1.278e4

count

_HUMD_OFFSET

0.0

count

_PRES_OFFSET

4.369e4

count

_TEMP_GAIN

2.017e-2

deg_c/count

_HUMD_GAIN

6.104e-3

%/count

_PRES_GAIN

1.831e-2

hPa/count

,where ransformation coefficient from voltage to adc count is given with c2V = 2.0 * 10/2**15 [V/count], because output signal from sensor is measured with single-end not differential. These parameters are managed by SDF with observe.snap. So, plase do not change this file.

Temporary channels in IX0

Place

Sensor

Channel name

picture

Memo

IX0

Temporary

K1:PEM-IX0_SENSOR(1-12)

pic

Will be removed

Temporary channels in IY0

Place

Sensor

Channel name

picture

Memo

IY0

Temporary

K1:PEM-IY0_SENSOR(1-12)

pic

Will be removed

Channel Name Definition

Definition of the PEM channel name 

K1:PEM-(SENSOR)_(PLACE1)_(PLACE2)_(DOF)

SENSOR

センサーの種類がここに該当する。

Name

Purpose

ONDTR

Ondotori sensor

ACC

Accelerometer

MIC

Microphone

MAG

Magnetometer

SEIS

Seismometer

WEATHER

Weather station

SENSOR(or SIGNAL; すぐに決めてどちらかにする)

--

Comment

  • 現状(2018/12/26)は以上だが、今後PEMが足されるにつれて追加する。(yokozawa)

PLACE1

広い意味のエリア名が該当する？

Name

Purpose

PSL

in the PSL Room area

IX

around the IX area

IY

around the IY area

EX

around the EX area

EY

around the EY area

IXV

in the IXV area

IYV

in the IYV area

EXV

in the EXV area

EYV

in the EYV area

TMSX

around the TMSX area

TMSY

around the TMSY area

PCALX

around the PCALX area

PCALY

around the PCALY area

PR

around the PR area including chamber

BS

around the BS area including chamber

SR

around the SR area including chamber

IMC

around the MCi, MCe, MCo area

IFI

around the IFI area including table, chamber

OMC

around the OMC area including table, chamber

POP

around the POP area including table, chamber

POS

around the POS area including talbe, chamber

RACK

in the DGS Rack

FIELD

on the field

BOOTH

in the "any" clean booth

MOZUMI

in the mozumi building

Comment

  • (A chamberを加えるかどうかは議論が必要だが、今の所置く余裕がない)

PLACE2

センサーが設置されている構造物の名前が該当する？

Name

Purpose

GND

on the ground

PRERI

on the periscope

CHAMBER

on the chamber

BEAMDUCT

on the beamduct

TABLE

on the table

ONTABLE

Microphone on the table???

Comment

  • もし該当しない場合、PLACE2を省略して、DOFに行ってもいいのだろうか。　(Miyo)

DOF

DOFが該当する。センサーが複数個のシグナルを持つ場合、それぞれの名前が該当する？

Name

Purpose

X/Y/Z

X,Y,Z axis as KAGRA cordinate

18V/24V

type of the DC power supply

TEMPERATURE/HUMIDITY/PRESSSURE

signals of the both ondotori and weather station

SDF

latest snapfile

2018/12/03 Update, miyo

Model

snapfile

Managed date

klog

k1pemiy0

observe.snap

Dec 03 09:49:41 2018

7249

k1pemix1

observe.snap

Nov 28 19:27:27 2018

7249

k1pemex1

observe.snap

Nov 28 19:25:46 2018

7249

k1pemey1

observe.snap

Nov 30 17:15:59 2018

7249

KAGRA/Subgroups/PEM/Channels (last edited 2019-05-11 12:31:04 by KousekiMiyo)