Acceptance Test

Flow chart

ALS Configuration

A: Design phase

Templates for A

Check sheets

A01

hoge

B: Installation phase

Templates for B

Check sheets

B01

Cable connection
- Resistance (Ohom)
- Continuity (OK/NO)
Calibration (LVDT, ACC)
- Calibration (plot, polarity, coefficient)
- Sensor noise (plot)
Working point and dynamic range with FR, Limit SW
- Range (from -mm to +mm)
- Minimum range (mm)
- Optimal point (mm)
- Limit SW (on/off)
Tuned frequencies of GAS Filter/IP
- Frequency (TF, actuator efficiency)
- Maximum frequency (Hz)

B02

B03

B04

C: Integration phase

Templates for C

Check sheets

C01

Damping time
- RMS in spectrum (plot)
Healthy check
- Transfer function (plot)
- Resonant frequencies (PreQUA)
Noise budget
- Spectrum (plot)

C02

Check items on Software (Control)

Noise budget

Spectrum (plot)

Guardian

KAGRA/Subgroups/VIS/Acceptance Test (last edited 2020-12-04 11:38:31 by KousekiMiyo)

-  ⇤ ← Revision 1 as of 2020-08-27 14:06:18 → 
  Size: 737
  Editor: RyutaroTakahashi
  Comment:
+   ← Revision 23 as of 2020-09-23 15:35:22 → ⇥
  Size: 1471
  Editor: KousekiMiyo
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 1:
+<<TableOfContents(3)>>
-Line 2:
+Line 4:
+== Flow chart ==
{{https://gwdoc.icrr.u-tokyo.ac.jp/DocDB/0120/E2012025/001/VISworkflow-Overview.png|ALS Configuration|width=700}}
-Line 3:
+Line 7:
-== Check items on Hardware ==
=== Cable connection ===
* Resistance (Ohom)
* Continuity (O/X)
+== A: Design phase ==
=== Templates for A ===
[[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=xxx|Check sheets]]
-Line 8:
+Line 11:
-=== Calibration (LVDT, ACC) ===
* Calibration (plot, polarity, coefficient)
* Sensor noise (plot)
+=== A01 ===
 * hoge
-Line 12:
+Line 14:
-=== Working point and dynamic range with FR, Limit SW ===
* Range (from -mm to +mm)
* Minimum range (mm)
* Optimal point (mm)
* Limit SW (on/off)
+== B: Installation phase ==
=== Templates for B ===
[[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=11957|Check sheets]]
 Line 18:
-=== Tuned frequencies of GAS Filter/IP ===
* Frequency (TF, actuator efficiency)
* Maximum frequency (Hz)
+=== B01 ===
 * Cable connection
  * Resistance (Ohom)
  * Continuity (OK/NO)
 * Calibration (LVDT, ACC)
  * Calibration (plot, polarity, coefficient)
  * Sensor noise (plot)
 * Working point and dynamic range with FR, Limit SW
  * Range (from -mm to +mm)
  * Minimum range (mm)
  * Optimal point (mm)
  * Limit SW (on/off)
 * Tuned frequencies of GAS Filter/IP
  * Frequency (TF, actuator efficiency)
  * Maximum frequency (Hz)

=== B02 ===

=== B03 ===

=== B04 ===


== C: Integration phase ==
=== Templates for C ===
[[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=xxx|Check sheets]]

=== C01 ===
 * Damping time 
  * RMS in spectrum (plot)
 * Healthy check
  * Transfer function (plot)
  * Resonant frequencies (PreQUA)

 * Noise budget
  * Spectrum (plot)

=== C02 ===


------
-Line 23:
+Line 64:
-=== Healthy check template ===
* Transfer function (plot)
* Resonant frequencies (PreQUA)

=== Damping time ===
* RMS in spectrum (plot)
-Line 31:
+Line 66:
-* Spectrum (plot)
+ * Spectrum (plot)