|
Size: 737
Comment:
|
Size: 1435
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 1: | Line 1: |
| <<TableOfContents(3)>> |
|
| Line 2: | Line 4: |
| == Flow chart == {{https://gwdoc.icrr.u-tokyo.ac.jp/DocDB/0120/E2012025/002/VISworkflow-Overview.png|WorkFlow|width=700}} |
|
| Line 3: | Line 7: |
| == Check items on Hardware == === Cable connection === * Resistance (Ohom) * Continuity (O/X) |
== A: Design phase == [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=xxx|Check sheets templates for A]] |
| Line 8: | Line 10: |
| === Calibration (LVDT, ACC) === * Calibration (plot, polarity, coefficient) * Sensor noise (plot) |
=== A01 === * hoge |
| Line 12: | Line 13: |
| === Working point and dynamic range with FR, Limit SW === * Range (from -mm to +mm) * Minimum range (mm) * Optimal point (mm) * Limit SW (on/off) |
== B: Installation phase == [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=11957|Check sheets templates for B]] |
| Line 18: | Line 16: |
| === Tuned frequencies of GAS Filter/IP === * Frequency (TF, actuator efficiency) * Maximum frequency (Hz) |
=== B01 === * Cable connection * Resistance (Ohom) * Continuity (OK/NO) * Calibration (LVDT, ACC) * Calibration (plot, polarity, coefficient) * Sensor noise (plot) * Working point and dynamic range with FR, Limit SW * Range (from -mm to +mm) * Minimum range (mm) * Optimal point (mm) * Limit SW (on/off) * Tuned frequencies of GAS Filter/IP * Frequency (TF, actuator efficiency) * Maximum frequency (Hz) === B02 === === B03 === === B04 === == C: Integration phase == [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=xxx|Check sheets templates for C]] === C01 === * Damping time * RMS in spectrum (plot) * Healthy check * Transfer function (plot) * Resonant frequencies (PreQUA) * Noise budget * Spectrum (plot) === C02 === ------ |
| Line 23: | Line 61: |
| === Healthy check template === * Transfer function (plot) * Resonant frequencies (PreQUA) === Damping time === * RMS in spectrum (plot) |
|
| Line 31: | Line 63: |
| * Spectrum (plot) | * Spectrum (plot) |
Contents
Acceptance Test
Flow chart
A: Design phase
A01
- hoge
B: Installation phase
B01
- Cable connection
- Resistance (Ohom)
- Continuity (OK/NO)
- Calibration (LVDT, ACC)
- Calibration (plot, polarity, coefficient)
- Sensor noise (plot)
- Working point and dynamic range with FR, Limit SW
- Range (from -mm to +mm)
- Minimum range (mm)
- Optimal point (mm)
- Limit SW (on/off)
- Tuned frequencies of GAS Filter/IP
- Frequency (TF, actuator efficiency)
- Maximum frequency (Hz)
B02
B03
B04
C: Integration phase
C01
- Damping time
- RMS in spectrum (plot)
- Healthy check
- Transfer function (plot)
- Resonant frequencies (PreQUA)
- Noise budget
- Spectrum (plot)
C02
Check items on Software (Control)
Noise budget
- Spectrum (plot)