Differences between revisions 25 and 37 (spanning 12 versions)
⇤ ← Revision 25 as of 2020-09-23 15:57:37 →
Size: 1435
Editor: KousekiMiyo
Comment:
← Revision 37 as of 2020-09-23 17:57:15 → ⇥
Size: 2036
Editor: KousekiMiyo
Comment:
Deletions are marked like this. Additions are marked like this.
Line 5: Line 5:
{{https://gwdoc.icrr.u-tokyo.ac.jp/DocDB/0120/E2012025/002/VISworkflow-Overview.png|WorkFlow|width=700}} {{https://gwdoc.icrr.u-tokyo.ac.jp/DocDB/0120/E2012025/003/VISworkflow-Overview.png|WorkFlow|width=600}}
Line 10: Line 10:
=== A01 ===
 * hoge		 === A01 : Could the simulation satisfy the requirement? ===
==== Input ====
* KAGRA requirements
 * Input the design sensitivity (ref. xxx)
 * Input the DAC limit (ref. xxx)
* Suspension model
 * plant model : rigid body model by SUMCON (ref. xxx)
 * control model : LTI model by Matlab simlink (ref. xxx)
 * noise model : seismic noise, control noise (ref. xxx)

==== Content ====


==== Output ====
 * Transfer function
  * transfer function of the suspension (ref. xxx)
 * Noises
  * requirement for sensor noises (ref. xxx)
  * requirement for actuator noises (ref. xxx)
Line 33: Line 50:
 * Please write
  * aaaa
Line 35: Line 54:
 * Please write
  * aaaa
Line 37: Line 58:
 * Please write
  * aaaa
Line 48: Line 70:
Line 51: Line 72:
 * Automation
  * check the guardian transition
Line 53: Line 76:


------




== Check items on Software (Control) ==

=== Noise budget ===
 * Spectrum (plot)

=== Guardian ===		  * Please write
  * aaaa

Contents

  1. Acceptance Test
    1. Flow chart
    2. A: Design phase
      1. A01 : Could the simulation satisfy the requirement?
    3. B: Installation phase
      1. B01
      2. B02
      3. B03
      4. B04
    4. C: Integration phase
      1. C01
      2. C02

Acceptance Test

Flow chart

WorkFlow

A: Design phase

Check sheets templates for A

A01 : Could the simulation satisfy the requirement?

Input

* KAGRA requirements

  • Input the design sensitivity (ref. xxx)
  • Input the DAC limit (ref. xxx)

* Suspension model

  • plant model : rigid body model by SUMCON (ref. xxx)
  • control model : LTI model by Matlab simlink (ref. xxx)
  • noise model : seismic noise, control noise (ref. xxx)

Content

Output

  • Transfer function
    • transfer function of the suspension (ref. xxx)
  • Noises
    • requirement for sensor noises (ref. xxx)
    • requirement for actuator noises (ref. xxx)

B: Installation phase

Check sheets templates for B

B01

  • Cable connection
    • Resistance (Ohom)
    • Continuity (OK/NO)
  • Calibration (LVDT, ACC)
    • Calibration (plot, polarity, coefficient)
    • Sensor noise (plot)
  • Working point and dynamic range with FR, Limit SW
    • Range (from -mm to +mm)
    • Minimum range (mm)
    • Optimal point (mm)
    • Limit SW (on/off)
  • Tuned frequencies of GAS Filter/IP
    • Frequency (TF, actuator efficiency)
    • Maximum frequency (Hz)

B02

  • Please write
    • aaaa

B03

  • Please write
    • aaaa

B04

  • Please write
    • aaaa

C: Integration phase

Check sheets templates for C

C01

  • Damping time
    • RMS in spectrum (plot)
  • Healthy check
    • Transfer function (plot)
    • Resonant frequencies (PreQUA)
  • Noise budget
    • Spectrum (plot)
  • Automation
    • check the guardian transition

C02

  • Please write
    • aaaa

KAGRA/Subgroups/VIS/Acceptance Test (last edited 2020-12-04 11:38:31 by KousekiMiyo)