Acceptance Test

Flow chart

Flow chart for the acceptance check

WorkFlow

A: Design phase

Check sheets templates for A

A01 : Simulation satisfy the requirement?

Input

KAGRA requirements
- Input the design sensitivity (ref. xxx)
- Input the DAC limit (ref. xxx)
Suspension model
- plant model : rigid body model by SUMCON (ref. xxx)
- control model : LTI model by Matlab simlink (ref. xxx)
- noise model : seismic noise, control noise (ref. xxx)

Output

Transfer function
- transfer function of the suspension (ref. xxx)
Noises
- requirement for sensor noises (ref. xxx)
- requirement for actuator noises (ref. xxx)

Content

B: Installation phase

Check sheets templates for B

B01 : Tower is ready to combine?

Cable connection
- Resistance (Ohom)
- Continuity (OK/NO)
Calibration (LVDT, ACC)
- Calibration (plot, polarity, coefficient)
- Sensor noise (plot)
Working point and dynamic range with FR, Limit SW
- Range (from -mm to +mm)
- Minimum range (mm)
- Optimal point (mm)
- Limit SW (on/off)
Tuned frequencies of GAS Filter/IP
- Frequency (TF, actuator efficiency)
- Maximum frequency (Hz)

B02 : Payload is ready to combine?

　Please write

B03 : Can we measure the TF in air?

　Please write

B04 : Can we measure the TF in vacuum?

Damping time
- RMS in spectrum (plot)
Healthy check
- Transfer function (plot)
- Resonant frequencies (PreQUA)

C: Integration phase

Check sheets templates for C

C01 : Can we control the suspension in local?

Noise budget
- Spectrum (plot)
Automation
- check the guardian transition

C02 : Can we control the suspension in global?

Please write
- aaaa

KAGRA/Subgroups/VIS/Acceptance Test (last edited 2020-12-04 11:38:31 by KousekiMiyo)

-  ⇤ ← Revision 28 as of 2020-09-23 16:00:26 → 
  Size: 1368
  Editor: KousekiMiyo
  Comment:
+   ← Revision 47 as of 2020-09-24 15:26:08 → ⇥
  Size: 2328
  Editor: KousekiMiyo
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 5:
-{{https://gwdoc.icrr.u-tokyo.ac.jp/DocDB/0120/E2012025/002/VISworkflow-Overview.png|WorkFlow|width=600}}
+[[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=12025| Flow chart for the acceptance check ]]

{{https://gwdoc.icrr.u-tokyo.ac.jp/DocDB/0120/E2012025/004/VISworkflow.png|WorkFlow|width=600}}
-Line 10:
+Line 12:
-=== A01 ===
 * hoge
+=== A01 : Simulation satisfy the requirement? ===
==== Input ====
 * KAGRA requirements
  * Input the design sensitivity (ref. xxx)
  * Input the DAC limit (ref. xxx)
 * Suspension model
  * plant model : rigid body model by SUMCON (ref. xxx)
  * control model : LTI model by Matlab simlink (ref. xxx)
  * noise model : seismic noise, control noise (ref. xxx)

==== Output ====
 * Transfer function
  * transfer function of the suspension (ref. xxx)
 * Noises
  * requirement for sensor noises (ref. xxx)
  * requirement for actuator noises (ref. xxx)

==== Content ====
-Line 16:
+Line 36:
-=== B01 ===
+=== B01 : Tower is ready to combine? ===
-Line 32:
+Line 52:
-=== B02 ===
+=== B02 : Payload is ready to combine? ===
 * {i}　Please write
-Line 34:
+Line 55:
-=== B03 ===
+=== B03 : Can we measure the TF in air? ===
 * {i}　Please write
-Line 36:
+Line 58:
-=== B04 ===


== C: Integration phase ==
[[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=xxx|Check sheets templates for C]]

=== C01 ===
+=== B04 : Can we measure the TF in vacuum? ===
-Line 48:
+Line 64:
+== C: Integration phase ==
[[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=xxx|Check sheets templates for C]]

=== C01 : Can we control the suspension in local? ===
-Line 53:
+Line 74:
-=== C02 ===
 * 
  *
+=== C02 : Can we control the suspension in global? ===
 * Please write
  * aaaa