Differences between revisions 30 and 42 (spanning 12 versions)
⇤ ← Revision 30 as of 2020-09-23 16:02:52 →
Size: 1464
Editor: KousekiMiyo
Comment:
← Revision 42 as of 2020-09-23 18:12:51 → ⇥
Size: 2176
Editor: KousekiMiyo
Comment:
Deletions are marked like this. Additions are marked like this.
Line 5: Line 5:
{{https://gwdoc.icrr.u-tokyo.ac.jp/DocDB/0120/E2012025/002/VISworkflow-Overview.png|WorkFlow|width=600}} {{https://gwdoc.icrr.u-tokyo.ac.jp/DocDB/0120/E2012025/003/VISworkflow-Overview.png|WorkFlow|width=600}}
Line 10: Line 10:
=== A01 ===
 * hoge		 === A01 : Simulation satisfy the requirement? ===
==== Input ====
 * KAGRA requirements
  * Input the design sensitivity (ref. xxx)
  * Input the DAC limit (ref. xxx)
 * Suspension model
  * plant model : rigid body model by SUMCON (ref. xxx)
  * control model : LTI model by Matlab simlink (ref. xxx)
  * noise model : seismic noise, control noise (ref. xxx)

==== Content ====


==== Output ====
 * Transfer function
  * transfer function of the suspension (ref. xxx)
 * Noises
  * requirement for sensor noises (ref. xxx)
  * requirement for actuator noises (ref. xxx)
Line 16: Line 33:
=== B01 === === B01 : Tower is ready to combine? ===
Line 32: Line 49:
=== B02 === === B02 : Payload is ready to combine? ===
Line 36: Line 53:
=== B03 === === B03 : Can we measure the TF in air? ===
Line 40: Line 57:
=== B04 ===
 * Please write
  * aaaa

== C: Integration phase ==
[[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=xxx|Check sheets templates for C]]

=== C01 ===		 === B04 : Can we measure the TF in vacuum? ===
Line 53: Line 63:

== C: Integration phase ==
[[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=xxx|Check sheets templates for C]]

=== C01 : Can we control the suspension? ===
Line 58: Line 73:
=== C02 === === C02 : Can we ===

Contents

  1. Acceptance Test
    1. Flow chart
    2. A: Design phase
      1. A01 : Simulation satisfy the requirement?
    3. B: Installation phase
      1. B01 : Tower is ready to combine?
      2. B02 : Payload is ready to combine?
      3. B03 : Can we measure the TF in air?
      4. B04 : Can we measure the TF in vacuum?
    4. C: Integration phase
      1. C01 : Can we control the suspension?
      2. C02 : Can we

Acceptance Test

Flow chart

WorkFlow

A: Design phase

Check sheets templates for A

A01 : Simulation satisfy the requirement?

Input

  • KAGRA requirements
    • Input the design sensitivity (ref. xxx)
    • Input the DAC limit (ref. xxx)
  • Suspension model
    • plant model : rigid body model by SUMCON (ref. xxx)
    • control model : LTI model by Matlab simlink (ref. xxx)
    • noise model : seismic noise, control noise (ref. xxx)

Content

Output

  • Transfer function
    • transfer function of the suspension (ref. xxx)
  • Noises
    • requirement for sensor noises (ref. xxx)
    • requirement for actuator noises (ref. xxx)

B: Installation phase

Check sheets templates for B

B01 : Tower is ready to combine?

  • Cable connection
    • Resistance (Ohom)
    • Continuity (OK/NO)
  • Calibration (LVDT, ACC)
    • Calibration (plot, polarity, coefficient)
    • Sensor noise (plot)
  • Working point and dynamic range with FR, Limit SW
    • Range (from -mm to +mm)
    • Minimum range (mm)
    • Optimal point (mm)
    • Limit SW (on/off)
  • Tuned frequencies of GAS Filter/IP
    • Frequency (TF, actuator efficiency)
    • Maximum frequency (Hz)

B02 : Payload is ready to combine?

  • Please write
    • aaaa

B03 : Can we measure the TF in air?

  • Please write
    • aaaa

B04 : Can we measure the TF in vacuum?

  • Damping time
    • RMS in spectrum (plot)
  • Healthy check
    • Transfer function (plot)
    • Resonant frequencies (PreQUA)

C: Integration phase

Check sheets templates for C

C01 : Can we control the suspension?

  • Noise budget
    • Spectrum (plot)
  • Automation
    • check the guardian transition

C02 : Can we

  • Please write
    • aaaa

KAGRA/Subgroups/VIS/Acceptance Test (last edited 2020-12-04 11:38:31 by KousekiMiyo)