Acceptance Test

Flow chart

ALS Configuration

A: Design phase

Templates for A

Check sheets

A01

hoge

B: Installation phase

Templates for B

Check sheets

B01

Cable connection
- Resistance (Ohom)
- Continuity (OK/NO)
Calibration (LVDT, ACC)
- Calibration (plot, polarity, coefficient)
- Sensor noise (plot)
Working point and dynamic range with FR, Limit SW
- Range (from -mm to +mm)
- Minimum range (mm)
- Optimal point (mm)
- Limit SW (on/off)
Tuned frequencies of GAS Filter/IP
- Frequency (TF, actuator efficiency)
- Maximum frequency (Hz)

B02

B03

B04

C: Integration phase

Templates for C

Check sheets

C01

Healthy check
- Transfer function (plot)
- Resonant frequencies (PreQUA)

C02

Check items on Software (Control)

Healthy check template

Transfer function (plot)
Resonant frequencies (PreQUA)

Damping time

RMS in spectrum (plot)

Noise budget

Spectrum (plot)

Guardian

KAGRA/Subgroups/VIS/Acceptance Test (last edited 2020-12-04 11:38:31 by KousekiMiyo)

-  ⇤ ← Revision 6 as of 2020-09-23 14:25:42 → 
  Size: 1089
  Editor: KousekiMiyo
  Comment:
+   ← Revision 22 as of 2020-09-23 14:54:41 → ⇥
  Size: 1531
  Editor: KousekiMiyo
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 1:
+<<TableOfContents(3)>>
-Line 2:
+Line 4:
+== Flow chart ==
{{https://gwdoc.icrr.u-tokyo.ac.jp/DocDB/0120/E2012025/001/VISworkflow-Overview.png|ALS Configuration|width=700}}
-Line 3:
+Line 7:
+== A: Design phase ==
=== Templates for A ===
[[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=xxx|Check sheets]]
-Line 4:
+Line 11:
-== (A) Design phase ==
=== A01===
+=== A01 ===
-Line 8:
+Line 14:
+== B: Installation phase ==
=== Templates for B ===
[[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=11957|Check sheets]]
-Line 9:
+Line 18:
-== (B) Installation phase ==
-Line 13:
+Line 21:
-  * Continuity (O/X)
+  * Continuity (OK/NO)
 * Calibration (LVDT, ACC)
  * Calibration (plot, polarity, coefficient)
  * Sensor noise (plot)
 * Working point and dynamic range with FR, Limit SW
  * Range (from -mm to +mm)
  * Minimum range (mm)
  * Optimal point (mm)
  * Limit SW (on/off)
 * Tuned frequencies of GAS Filter/IP
  * Frequency (TF, actuator efficiency)
  * Maximum frequency (Hz)

=== B02 ===

=== B03 ===

=== B04 ===
-Line 16:
+Line 41:
-== (C) Integration phase ==
+== C: Integration phase ==
=== Templates for C ===
[[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=xxx|Check sheets]]
-Line 18:
+Line 46:
+ * Healthy check
  * Transfer function (plot)
  * Resonant frequencies (PreQUA)
-Line 22:
+Line 53:
+------
-Line 24:
+Line 56:
-------
-Line 26:
+Line 57:
-== Check items on Hardware ==
[[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=11957|Check sheet]]

=== Cable connection ===
 * Resistance (Ohom)
 * Continuity (O/X)

=== Calibration (LVDT, ACC) ===
 * Calibration (plot, polarity, coefficient)
 * Sensor noise (plot)

=== Working point and dynamic range with FR, Limit SW ===
 * Range (from -mm to +mm)
 * Minimum range (mm)
 * Optimal point (mm)
 * Limit SW (on/off)

=== Tuned frequencies of GAS Filter/IP ===
 * Frequency (TF, actuator efficiency)
 * Maximum frequency (Hz)