Acceptance Test

Flow chart

WorkFlow

A: Design phase

Check sheets templates for A

A01 : Could the simulation satisfy the requirement?

Input

* KAGRA requirements

Input the design sensitivity (ref. xxx)
Input the DAC limit (ref. xxx)

* Suspension model

plant model : rigid body model by SUMCON (ref. xxx)
control model : LTI model by Matlab simlink (ref. xxx)
noise model : seismic noise, control noise (ref. xxx)

Content

Output

Transfer function
- transfer function of the suspension (ref. xxx)
Noises
- requirement for sensor noises (ref. xxx)
- requirement for actuator noises (ref. xxx)

B: Installation phase

Check sheets templates for B

B01

Cable connection
- Resistance (Ohom)
- Continuity (OK/NO)
Calibration (LVDT, ACC)
- Calibration (plot, polarity, coefficient)
- Sensor noise (plot)
Working point and dynamic range with FR, Limit SW
- Range (from -mm to +mm)
- Minimum range (mm)
- Optimal point (mm)
- Limit SW (on/off)
Tuned frequencies of GAS Filter/IP
- Frequency (TF, actuator efficiency)
- Maximum frequency (Hz)

B02

Please write
- aaaa

B03

Please write
- aaaa

B04

Please write
- aaaa

C: Integration phase

Check sheets templates for C

C01

Damping time
- RMS in spectrum (plot)
Healthy check
- Transfer function (plot)
- Resonant frequencies (PreQUA)
Noise budget
- Spectrum (plot)
Automation
- check the guardian transition

C02

Please write
- aaaa

KAGRA/Subgroups/VIS/Acceptance Test (last edited 2020-12-04 11:38:31 by KousekiMiyo)

-  ⇤ ← Revision 7 as of 2020-09-23 14:27:34 → 
  Size: 1087
  Editor: KousekiMiyo
  Comment:
+   ← Revision 37 as of 2020-09-23 17:57:15 → ⇥
  Size: 2036
  Editor: KousekiMiyo
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 1:
+<<TableOfContents(3)>>

= Acceptance Test =
== Flow chart ==
{{https://gwdoc.icrr.u-tokyo.ac.jp/DocDB/0120/E2012025/003/VISworkflow-Overview.png|WorkFlow|width=600}}

== A: Design phase ==
[[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=xxx|Check sheets templates for A]]

=== A01 : Could the simulation satisfy the requirement? ===
==== Input ====
* KAGRA requirements
 * Input the design sensitivity (ref. xxx)
 * Input the DAC limit (ref. xxx)
* Suspension model
 * plant model : rigid body model by SUMCON (ref. xxx)
 * control model : LTI model by Matlab simlink (ref. xxx)
 * noise model : seismic noise, control noise (ref. xxx)

==== Content ====
-Line 3:
+Line 23:
-= Acceptance Test =
== A: Design phase ==
=== A01 ===
 * hoge
+==== Output ====
 * Transfer function
  * transfer function of the suspension (ref. xxx)
 * Noises
  * requirement for sensor noises (ref. xxx)
  * requirement for actuator noises (ref. xxx)
-Line 10:
+Line 31:
+[[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=11957|Check sheets templates for B]]
-Line 14:
+Line 37:
+ * Calibration (LVDT, ACC)
  * Calibration (plot, polarity, coefficient)
  * Sensor noise (plot)
 * Working point and dynamic range with FR, Limit SW
  * Range (from -mm to +mm)
  * Minimum range (mm)
  * Optimal point (mm)
  * Limit SW (on/off)
 * Tuned frequencies of GAS Filter/IP
  * Frequency (TF, actuator efficiency)
  * Maximum frequency (Hz)

=== B02 ===
 * Please write
  * aaaa

=== B03 ===
 * Please write
  * aaaa

=== B04 ===
 * Please write
  * aaaa
-Line 16:
+Line 62:
+[[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=xxx|Check sheets templates for C]]
-Line 17:
+Line 65:
+ * Damping time 
  * RMS in spectrum (plot)
 * Healthy check
  * Transfer function (plot)
  * Resonant frequencies (PreQUA)
 * Noise budget
  * Spectrum (plot)
 * Automation
  * check the guardian transition
-Line 19:
+Line 76:
-------

== Check items on Hardware ==
[[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=11957|Check sheet]]

=== Cable connection ===
 * Resistance (Ohom)
 * Continuity (O/X)

=== Calibration (LVDT, ACC) ===
 * Calibration (plot, polarity, coefficient)
 * Sensor noise (plot)

=== Working point and dynamic range with FR, Limit SW ===
 * Range (from -mm to +mm)
 * Minimum range (mm)
 * Optimal point (mm)
 * Limit SW (on/off)

=== Tuned frequencies of GAS Filter/IP ===
 * Frequency (TF, actuator efficiency)
 * Maximum frequency (Hz)

== Check items on Software (Control) ==
=== Healthy check template ===
 * Transfer function (plot)
 * Resonant frequencies (PreQUA)

=== Damping time ===
 * RMS in spectrum (plot)

=== Noise budget ===
 * Spectrum (plot)

=== Guardian ===
+ * Please write
  * aaaa