Size: 2165
Comment:
|
Size: 2891
Comment:
|
Deletions are marked like this. | Additions are marked like this. |
Line 3: | Line 3: |
==== original schedule ==== | ==== Schedule ==== |
Line 5: | Line 5: |
* 25th Jan - (2 weeks) Assembling and Test Hanging with dummy mirror | * 25th Jan - (2 weeks) Assembling and Test Hanging with an Al dummy mirror |
Line 9: | Line 9: |
==== Disassembling at Mitaka [Ohishi] ==== status: finished. (12th-19th) [problem] * 2 nuts stuck: solved by Hirata-san * A Cu screw stuck: solved by Hirata-san |
==== Disassembling at ATC Mitaka [Ohishi] (12th-19th Jan.) ==== * Two nuts stuck. Hirata-san removed them. * A Cu screw stuck. Hirata-san removed it. |
Line 15: | Line 13: |
status: finished. [problem] * ultra sonic washer broken 20th ordered on 22th(Fri) will be arrive at Mitaka on 26th(Tue) * 8 screws for adjusting the IM holding plate was dirty Solution: order new screws (by Takahashi-san) |
* The ultra sonic washer at ATC was broken on 20th Jan. A new washer was ordered on 22th(Fri) and arrived at Mitaka on 25th(Mon). * Eight screws for adjusting the IM holding plate was dirty. Takahashi-san ordered similar screws. |
Line 22: | Line 18: |
status: finished. * coil bobbin [Takahashi-san] * coil winding [students of Ando-lab] [problem] coil wires from the bobbin to Dsub connector were too short(20cm). The length of Must be 40cm or more. At the end of coil wires, D-sub pins are swaged. We have run short of pins and waiting for delivery on 29th. [problem ]Peeling off the coating of wires longer than the length of those pins make the wire broken easily. * D-sub fixture plates [Takahashi-san] [problem] M3 holes were drilled to phi3.2 holes. * mirror container [Tatsumi-san] [problem] * magnets for dummy mirror (4 ; 2-phi-L-5mm Nd magnets) [Tomaru, Yamamoto] [] * some screws in replace with Cu screws [Ohishi] |
* Coil bobbin [Takahashi-san, Tatsumi-san] [[http://gwdoc.icrr.u-tokyo.ac.jp/DocDB/0047/T1604741/001/Coil_Preparation_2016.pdf|coil bobbin]] * The outer diameter of the coil has been changed from 14.2mm to 14.5mm. * Due to this change, the number of winding becomes 39 from 41. * Delivered to Kamioka on 4th Feb. * Coil winding [Kuwahara-san, and Ushiba-san from U-Tokyo] * Lead wires from the bobbin to Dsub connector were too short (20cm). The length must be 40cm or more. * At the end of the lead wires, D-sub pins are swaged. We have run short of pins and waiting for delivery on 29th Feb(Mon). * Peeling off the coating of wires longer than the length of those pins make the wire broken easily. * D-sub connector plates [Takahashi-san] [[attachment:D-sub_connector_plate.pdf|{{attachment:D-sub_connector_plate.pdf||width=600}}]]<<BR>> * M3 holes were drilled to phi3.2 holes. * Mirror container [Tatsumi-san] [[attachment:MirrorContainer.pdf|{{attachment:MirrorContainer.pdf||width=600}}]]<<BR>> * Magnets for dummy mirror (4 ; 2-phi-L-5mm Nd magnets) [Tomaru, Yamamoto] * Screws in replace with Cu screws [Ohishi] |
Line 36: | Line 36: |
==== pico-motors and PZTs ==== | ==== Pico-motors and PZTs ==== |
Line 39: | Line 39: |
==== coil driver ==== | ==== Coil driver ==== |
Line 41: | Line 41: |
==== cables ==== | ==== Cables ==== |
Line 43: | Line 43: |
==== Assembling [Tomaru, Ohishi, Yamamoto] ==== | ==== Assembling [Tomaru-san, Ohishi, Yamamoto-san] ==== |
Line 51: | Line 51: |
==== Transportation to the End ==== | ==== Transportation to the End [Prof. Kimura, Sawada-san, Tomaru-san(KEK),]==== KEK |
Line 53: | Line 54: |
==== Mirrors ==== Two TAMA PRM mirrors (with about 50% and 90% reflectivities each, resultant contrast becomes 96%) were delivered to Kamioka on 12th Feb. ==== Stages ==== * Condensation * Vacuum compatibility? |
iKAGRA ETM suspension preparation log
Schedule
- 12th Jan- (2 weeks) Disassembling, Washing, and transportation
- 25th Jan - (2 weeks) Assembling and Test Hanging with an Al dummy mirror
- 7th Feb- (1 week) coil winding, measurement of transfer function, transportation to the End area and installation test
- 15th Feb- (1 week)installation
Disassembling at ATC Mitaka [Ohishi] (12th-19th Jan.)
- Two nuts stuck. Hirata-san removed them.
- A Cu screw stuck. Hirata-san removed it.
Washing and transportation to Kamioka [Hirata-san]
- The ultra sonic washer at ATC was broken on 20th Jan. A new washer was ordered on 22th(Fri) and arrived at Mitaka on 25th(Mon).
- Eight screws for adjusting the IM holding plate was dirty. Takahashi-san ordered similar screws.
New parts
- Coil bobbin [Takahashi-san, Tatsumi-san]
- The outer diameter of the coil has been changed from 14.2mm to 14.5mm.
- Due to this change, the number of winding becomes 39 from 41.
- Delivered to Kamioka on 4th Feb.
- Coil winding [Kuwahara-san, and Ushiba-san from U-Tokyo]
- Lead wires from the bobbin to Dsub connector were too short (20cm). The length must be 40cm or more.
- At the end of the lead wires, D-sub pins are swaged. We have run short of pins and waiting for delivery on 29th Feb(Mon).
- Peeling off the coating of wires longer than the length of those pins make the wire broken easily.
- D-sub connector plates [Takahashi-san]
- M3 holes were drilled to phi3.2 holes.
- Mirror container [Tatsumi-san]
- Magnets for dummy mirror (4 ; 2-phi-L-5mm Nd magnets) [Tomaru, Yamamoto]
- Screws in replace with Cu screws [Ohishi] [problem] replaced all Cu screws to stainless. Magnetism problem was indicated.
Pico-motors and PZTs
- We have 4 pico-motors except for x-axis (the direction of the light ) y, z, pitch, yaw
Coil driver
- We use KAGRA coil driver; we need to cheek its performance.
Cables
Assembling [Tomaru-san, Ohishi, Yamamoto-san]
- On 21th, suspension frame, security frame, xy stages completed
Hanging
- Hanging jig preparation
Transfer Function Measurement
==== Transportation to the End [Prof. Kimura, Sawada-san, Tomaru-san(KEK),]====
- KEK
Mirrors
- Two TAMA PRM mirrors (with about 50% and 90% reflectivities each, resultant contrast becomes 96%) were delivered to Kamioka on 12th Feb.
Stages
- Condensation
- Vacuum compatibility?