3480
Comment:
|
3558
|
Deletions are marked like this. | Additions are marked like this. |
Line 3: | Line 3: |
=== Schedule === | === 1. Schedule === |
Line 9: | Line 9: |
=== Disassembling in the ATC clean booth at Mitaka [Ohishi] (12th-19th Jan.) === | === 2. Disassembling in the ATC clean booth at Mitaka [Ohishi] (12th-19th Jan.) === |
Line 12: | Line 12: |
=== Washing and transportation to Kamioka [Hirata-san] === | === 3. Washing and transportation to Kamioka [Hirata-san] === |
Line 17: | Line 17: |
=== New parts === ==== Coil bobbin [Takahashi-san, Tatsumi-san] ==== |
=== 4. New parts preparation === ==== 4.1 Coil bobbin [Takahashi-san, Tatsumi-san] ==== |
Line 23: | Line 23: |
==== Coil winding [Kuwahara-san, and Ushiba-san from U-Tokyo, Lee-san from Okazaki, and Ohishi](8th-16th Feb.) ==== | ==== 4.2 Coil winding [Kuwahara-san, and Ushiba-san from U-Tokyo, Lee-san from Okazaki, and Ohishi](8th-16th Feb.) ==== |
Line 28: | Line 28: |
==== D-sub connector plates [Takahashi-san] ==== | ==== 4.3 D-sub connector plates [Takahashi-san] ==== |
Line 32: | Line 32: |
==== 15pin-9pin changer for coil driver output [Ushiba-san, Ohishi] ==== ==== Mirror container [Tatsumi-san] ==== [[attachment:MirrorContainer.pdf|{{attachment:MirrorContainer.pdf||width=600}}]]<<BR>> * Some plates once used for transportation of MC mirrors were used * Two places of the container were cut to avoid standoffs. ==== Attach magnets to dummy mirror (4 ; with the diameter of 2mm and the length of 5mm NdFeB magnets) [Tomaru, Yamamoto] ==== |
==== 4.4 15pin-9pin changer for coil driver output [Ushiba-san, Ohishi] ==== ==== 4.5 Screws in replace with Cu screws [Ohishi] ==== * Replaced all Cu screws to stainless screws. Magnetism problem was indicated. === 5. Jigs === |
Line 39: | Line 37: |
==== Screws in replace with Cu screws [Ohishi] ==== * Replaced all Cu screws to stainless screws. Magnetism problem was indicated. === Some parts ==== ==== Pico-motors and PZTs ==== |
==== Attach magnets to dummy mirror (4 ; with the diameter of 2mm and the length of 5mm NdFeB magnets) [Tomaru, Yamamoto] === 6. Some other items === ==== 6.1 Pico-motors and PZTs ==== |
Line 45: | Line 43: |
==== Coil drivers ==== | ==== 6.2 Coil drivers ==== |
Line 47: | Line 45: |
==== Cables ==== | ==== 6.3 Cables ==== |
Line 49: | Line 47: |
=== Assembling [Tomaru-san, Ohishi, Yamamoto-san] === | === 7. Assembling [Tomaru-san, Ohishi, Yamamoto-san] === |
Line 52: | Line 50: |
=== Hanging === | === 8. Hanging === |
Line 55: | Line 53: |
=== Transfer Function Measurement === | === 9. Transfer Function Measurement === |
Line 62: | Line 60: |
==== Mirror container [Tatsumi-san] ==== [[attachment:MirrorContainer.pdf|{{attachment:MirrorContainer.pdf||width=600}}]]<<BR>> * Some plates once used for transportation of MC mirrors were used * Two places of the container were cut to avoid standoffs. |
iKAGRA ETM suspension preparation log
1. Schedule
- 12th Jan- (2 weeks) Disassembling, Washing, and transportation
- 25th Jan - (2 weeks) Assembling and Test Hanging with an Al dummy mirror
- 7th Feb- (1 week) coil winding, measurement of transfer function, transportation to the End area and installation test
- 15th Feb- (1 week)installation
2. Disassembling in the ATC clean booth at Mitaka [Ohishi] (12th-19th Jan.)
- Two nuts stuck. Hirata-san removed them.
- A Cu screw stuck. Hirata-san removed it.
3. Washing and transportation to Kamioka [Hirata-san]
- The ultra sonic washer at ATC was broken on 20th Jan.
- A new washer was ordered on 22th(Fri) and arrived at Mitaka on 25th(Mon).
- Eight screws for adjusting the IM holding plate was dirty.
- Takahashi-san ordered similar screws.
4. New parts preparation
4.1 Coil bobbin [Takahashi-san, Tatsumi-san]
- The outer diameter of the coil has been changed from 14.2mm to 14.5mm.
- Due to this change, the number of winding becomes 39 from 41.
- Delivered to Kamioka on 4th Feb.
4.2 Coil winding [Kuwahara-san, and Ushiba-san from U-Tokyo, Lee-san from Okazaki, and Ohishi](8th-16th Feb.)
- We used coil winding machine.
- Lead wires from the bobbin to Dsub connector were too short (20cm). The length must be 40cm or more.
- At the end of the lead wires, D-sub pins are swaged. We have run short of pins and waiting for delivery on 29th Feb(Mon).
- Peeling off the coating of wires longer than the length of those pins make the wire broken easily.
4.3 D-sub connector plates [Takahashi-san]
- M3 holes were changed to phi3.1 holes. Yamamoto-san used drilling machine at Kamioka surface office.
- One must be careful about the pillar position in order to attach this plate to the suspension.
4.4 15pin-9pin changer for coil driver output [Ushiba-san, Ohishi]
4.5 Screws in replace with Cu screws [Ohishi]
- Replaced all Cu screws to stainless screws. Magnetism problem was indicated.
5. Jigs
- We used CLIO magnet fixture jigs.
==== Attach magnets to dummy mirror (4 ; with the diameter of 2mm and the length of 5mm NdFeB magnets) [Tomaru, Yamamoto]
6. Some other items
6.1 Pico-motors and PZTs
- We have 4 pico-motors except for x-axis (the direction of the light ) y, z, pitch, yaw
6.2 Coil drivers
- We use KAGRA coil driver; we need to cheek its performance.
6.3 Cables
7. Assembling [Tomaru-san, Ohishi, Yamamoto-san]
- On 21th, suspension frame, security frame, xy stages completed
8. Hanging
- Hanging jig preparation
9. Transfer Function Measurement
Transportation to the End [Prof. Kimura, Sawada-san, Tomaru-san(KEK),]
- KEK
Mirrors
- Two TAMA PRM mirrors (with about 50% and 90% reflectivities each, resultant contrast becomes 96%) were delivered to Kamioka on 12th Feb.
Mirror container [Tatsumi-san]
- Some plates once used for transportation of MC mirrors were used
- Two places of the container were cut to avoid standoffs.
=== Stages ====
- Condensation
- Vacuum compatibility?