Size: 3532
Comment:
|
Size: 3744
Comment:
|
Deletions are marked like this. | Additions are marked like this. |
Line 9: | Line 9: |
=== 2. Disassembling in the ATC clean booth at Mitaka [Ohishi] (12th-19th Jan.) === | === 2. Disassembling in the ATC clean booth at Mitaka(12th-19th Jan.) === |
Line 12: | Line 12: |
=== 3. Washing and transportation to Kamioka [Hirata-san] === | === 3. Washing and transportation to Kamioka === ==== [Hirata-san] ==== |
Line 33: | Line 34: |
==== Screws in replace with Cu screws [Ohishi] ==== | ==== 4.5 Screws in replace with Cu screws [Ohishi] ==== |
Line 35: | Line 36: |
=== 5 Jigs === | === 5. Jigs === |
Line 37: | Line 38: |
==== Attach magnets to dummy mirror (4 ; with the diameter of 2mm and the length of 5mm NdFeB magnets) [Tomaru, Yamamoto] | ==== Attach magnets to dummy mirror (4 ; with the diameter of 2mm and the length of 5mm NdFeB magnets) [Tomaru, Yamamoto] ==== |
Line 40: | Line 41: |
==== Pico-motors and PZTs ==== | ==== 6.1 Pico-motors and PZTs ==== |
Line 43: | Line 44: |
==== Coil drivers ==== | ==== 6.2 Coil drivers ==== |
Line 45: | Line 46: |
==== Cables ==== | ==== 6.3 Cables ==== |
Line 47: | Line 48: |
=== Assembling [Tomaru-san, Ohishi, Yamamoto-san] === On 21th, suspension frame, security frame, xy stages completed === Hanging === Hanging jig preparation === Transfer Function Measurement === === Transportation to the End [Prof. Kimura, Sawada-san, Tomaru-san(KEK),] === KEK ==== Mirrors ==== |
==== 6.4 Mirrors ==== |
Line 60: | Line 50: |
==== Mirror container [Tatsumi-san] ==== | ==== 6.5 Mirror container [Tatsumi-san] ==== |
Line 65: | Line 55: |
=== Stages ==== | === 6.6 Stages ==== |
Line 68: | Line 58: |
=== Installation === | === 7. Assembling [Tomaru-san, Ohishi, Yamamoto-san] === On 21th, suspension frame, security frame, xy stages completed === 8. Hanging [Yamamoto-san, Uchiyama-san, Doi-san, and Ohishi] === Hanging jig preparation === 9. Transfer Function Measurement [Shoda-san, Hayama-san, Ushiba-san, Kuwahara-san, Kokeyama-san, Kuwahara-san, Tomaru-san, Lee-san, and Ohishi] === === 10. Transportation to the End [Prof. Kimura, Sawada-san, Tomaru-san(KEK),] === KEK === 11. Installation === |
iKAGRA ETM suspension preparation log
1. Schedule
- 12th Jan- (2 weeks) Disassembling, Washing, and transportation
- 25th Jan - (2 weeks) Assembling and Test Hanging with an Al dummy mirror
- 7th Feb- (1 week) coil winding, measurement of transfer function, transportation to the End area and installation test
- 15th Feb- (1 week)installation
2. Disassembling in the ATC clean booth at Mitaka(12th-19th Jan.)
- Two nuts stuck. Hirata-san removed them.
- A Cu screw stuck. Hirata-san removed it.
3. Washing and transportation to Kamioka
[Hirata-san]
- The ultra sonic washer at ATC was broken on 20th Jan.
- A new washer was ordered on 22th(Fri) and arrived at Mitaka on 25th(Mon).
- Eight screws for adjusting the IM holding plate was dirty.
- Takahashi-san ordered similar screws.
4. New parts preparation
4.1 Coil bobbin [Takahashi-san, Tatsumi-san]
- The outer diameter of the coil has been changed from 14.2mm to 14.5mm.
- Due to this change, the number of winding becomes 39 from 41.
- Delivered to Kamioka on 4th Feb.
4.2 Coil winding [Kuwahara-san, and Ushiba-san from U-Tokyo, Lee-san from Okazaki, and Ohishi](8th-16th Feb.)
- We used coil winding machine.
- Lead wires from the bobbin to Dsub connector were too short (20cm). The length must be 40cm or more.
- At the end of the lead wires, D-sub pins are swaged. We have run short of pins and waiting for delivery on 29th Feb(Mon).
- Peeling off the coating of wires longer than the length of those pins make the wire broken easily.
4.3 D-sub connector plates [Takahashi-san]
- M3 holes were changed to phi3.1 holes. Yamamoto-san used drilling machine at Kamioka surface office.
- One must be careful about the pillar position in order to attach this plate to the suspension.
4.4 15pin-9pin changer for coil driver output [Ushiba-san, Ohishi]
4.5 Screws in replace with Cu screws [Ohishi]
- Replaced all Cu screws to stainless screws. Magnetism problem was indicated.
5. Jigs
- We used CLIO magnet fixture jigs.
Attach magnets to dummy mirror (4 ; with the diameter of 2mm and the length of 5mm NdFeB magnets) [Tomaru, Yamamoto]
6. Some other items
6.1 Pico-motors and PZTs
- We have 4 pico-motors except for x-axis (the direction of the light ) y, z, pitch, yaw
6.2 Coil drivers
- We use KAGRA coil driver; we need to cheek its performance.
6.3 Cables
6.4 Mirrors
- Two TAMA PRM mirrors (with about 50% and 90% reflectivities each, resultant contrast becomes 96%) were delivered to Kamioka on 12th Feb.
6.5 Mirror container [Tatsumi-san]
- Some plates once used for transportation of MC mirrors were used
- Two places of the container were cut to avoid standoffs.
=== 6.6 Stages ====
- Condensation
- Vacuum compatibility?
7. Assembling [Tomaru-san, Ohishi, Yamamoto-san]
- On 21th, suspension frame, security frame, xy stages completed
8. Hanging [Yamamoto-san, Uchiyama-san, Doi-san, and Ohishi]
- Hanging jig preparation
9. Transfer Function Measurement [Shoda-san, Hayama-san, Ushiba-san, Kuwahara-san, Kokeyama-san, Kuwahara-san, Tomaru-san, Lee-san, and Ohishi]
10. Transportation to the End [Prof. Kimura, Sawada-san, Tomaru-san(KEK),]
- KEK