Size: 4219
Comment:
|
Size: 657
Comment:
|
Deletions are marked like this. | Additions are marked like this. |
Line 1: | Line 1: |
== iKAGRA ETM suspension preparation log == | == Type-C suspension == |
Line 3: | Line 3: |
=== 1. Schedule === * 12th Jan- (2 weeks) Disassembling, Washing, and transportation * 25th Jan - (2 weeks) Assembling and Test Hanging with an Al dummy mirror * 7th Feb- (1 week) coil winding, measurement of transfer function, transportation to the End area and installation test * 15th Feb- (1 week)installation |
Type-C suspension is relatively small double pendulum. Among the big suspensions used in KAGRA, type-C is the smallest. Some of them were once used for TAMA300, originally designed by K. Arai in 1990s. So "TAMA-type suspension" is Type-C suspension. === iKAGRA === Five TAMA-type suspensions were used for iKAGRA.<<BR>> 3 PO type; MC_i, MC_e, MC_o and 2 TM or RM type; ETMX, ETMY. |
Line 9: | Line 10: |
=== 2. Disassembling in the ATC clean booth at Mitaka (12th-19th Jan.) === * One suspensions was moved from the desiccator at the west end of TAMA and the other was moved from the vacuum tank. * Two nuts stuck. Hirata-san removed them. * A Cu screw stuck. Hirata-san removed it. === 3. Washing and transportation to Kamioka [Hirata-san] === * The ultra sonic washer at ATC was broken on 20th Jan. <<BR>> A new washer was ordered on 22th(Fri) and arrived at Mitaka on 25th(Mon). * Eight screws for adjusting the IM holding plate was dirty.<<BR>> Takahashi-san ordered similar screws. === 4. New parts preparation === ==== 4.1 Coil bobbin ==== [Takahashi-san, Tatsumi-san] (Delivered to Kamioka on 4th Feb.) [[http://gwdoc.icrr.u-tokyo.ac.jp/DocDB/0047/T1604741/001/Coil_Preparation_2016.pdf|coil bobbin]] * The outer diameter of the coil has been changed from 14.2mm to 14.5mm. * Due to this change, the number of winding becomes 39 from 41. ==== 4.2 Coil winding ==== [Kuwahara-san, and Ushiba-san from U-Tokyo, Lee-san from Okazaki, and Ohishi] (8th-16th Feb.) * We used coil winding machine. * Lead wires from the bobbin to Dsub connector were too short (20cm). The length must be 40cm or more. * At the end of the lead wires, D-sub pins are swaged. We have run short of pins and waiting for delivery on 29th Feb(Mon). * Peeling off the coating of wires longer than the length of those pins make the wire broken easily. ==== 4.3 D-sub connector plates [Takahashi-san] ==== [[attachment:D-sub_connector_plate.pdf|{{attachment:D-sub_connector_plate.pdf||width=600}}]]<<BR>> * M3 holes were changed to phi3.1 holes. Yamamoto-san used drilling machine at Kamioka surface office. * One must be careful about the pillar position in order to attach this plate to the suspension. ==== 4.4 15pin-9pin changer for coil driver output [Ushiba-san, Ohishi] ==== ==== 4.5 Screws in replace with Cu screws [Ohishi] ==== * Replaced all Cu screws to stainless screws. Magnetism problem was indicated. === 5. Jigs === ==== 5.1 Magnet and standoff fixture jig ==== * We used ==== 5.2 Dock (mirror hanging jig) ==== (4 ; with the diameter of 2mm and the length of 5mm NdFeB magnets) [Tomaru-san, Yamamoto-san] |
Work log about 2 iKAGRA ETMs is [[KAGRA/Subgroups/VIS/Type-C/iKAGRA_ETM|here]]. |
Line 43: | Line 12: |
=== 6. Some other items === ==== 6.1 Pico-motors and PZTs ==== We have 4 pico-motors except for x-axis (the direction of the light ) y, z, pitch, yaw ==== 6.2 Coil drivers ==== We use KAGRA coil driver; we need to cheek its performance. ==== 6.3 Cables ==== |
=== Toward bKAGRA === |
Line 51: | Line 14: |
==== 6.4 Mirrors ==== Two TAMA PRM mirrors (with about 50% and 90% reflectivities each, resultant contrast becomes 96%) were delivered to Kamioka on 12th Feb. ==== 6.5 Mirror container [Tatsumi-san] ==== [[attachment:MirrorContainer.pdf|{{attachment:MirrorContainer.pdf||width=600}}]]<<BR>> * Some plates once used for transportation of MC mirrors were used * Two places of the container were cut to avoid standoffs. |
[[http://gwwiki.icrr.u-tokyo.ac.jp/JGWwiki/KAGRA/Subgroups/VIS/iKAGRAbKAGRA|Memo by Yamamoto-san]] === bKAGRA === |
Line 58: | Line 18: |
==== 6.6 Stages ==== * Condensation * Vacuum compatibility? === 7. Assembling === [Tomaru-san, Ohishi, Yamamoto-san] <<BR>> On 21th, suspension frame, security frame, xy stages completed |
|
Line 65: | Line 19: |
=== 8. Hanging === [Yamamoto-san, Uchiyama-san, Doi-san, and Ohishi] <<BR>> Hanging jig preparation === 9. Transfer Function Measurement (8th-16th Feb.) === [Shoda-san, Hayama-san, Ushiba-san, Kuwahara-san, Kokeyama-san, Kuwahara-san, Tomaru-san, Lee-san, and Ohishi] * First Shoda-san kindly made a simple model under PR2 digital system for this test. * === 10. Preparation of End area and suspension transportation to the End === [Kimura-san, Sawada-san, Tomaru-san, Prof. Suzuki, Telada-san, Uchiyam-san] * Uchiyama-san bought many things we need at the end area and KEK member transported them and cleaned the work area. === 11. Installation [] () === |
Type-C suspension
- Type-C suspension is relatively small double pendulum. Among the big suspensions used in KAGRA, type-C is the smallest. Some of them were once used for TAMA300, originally designed by K. Arai in 1990s. So "TAMA-type suspension" is Type-C suspension.
iKAGRA
Five TAMA-type suspensions were used for iKAGRA.
3 PO type; MC_i, MC_e, MC_o and 2 TM or RM type; ETMX, ETMY.Work log about 2 iKAGRA ETMs is here.
Toward bKAGRA