Stuff for Type B to do in March 2018 while waiting for deliveries

Possible schedule of selected tasks from below

• Week of 3/5
  • Finish any remaining SR2 SF stuff. (Enzo+2)
  • Get SRM mushroom installed (Hirata-san, Kimura-san, Sawada-san)
  • BF filter rebuild (Hirata-san+1)
    • Move filter table into SRM area.
    • Get additional heavy table.
    • Disassemble two filters
• Week of 3/12
  • Rack work (Enzo+1)
    • Find boxes for SR3 and SRM at Mozumi
    • Add boxes to SR3 and SRM racks
    • Do SR3 and SRM in-rack cables and labeling
    • Do SR3 in-air cables.
  • BF filter rebuild continued (Hirata-san+1)
    • Characterize 10 blades
    • Choose two matched sets
    • Rebuild two filters
• Week of 3/19 (Mitaka)
  • Make two sets of IM OSEMs
  • Make in-air pico adapter cable
  • Set up Dummy BS prism removal.
• Week of 3/26
  • SF Setup, Test
    • Set up SR3 assembly frame, weights.
    • Bring in remaining two SFs.
    • Remeasure load capacity, check for tilted keystone.
    • Install Cu segments on cap.
    • Wire and test LVDT.

Tasks that we have the necessary items to do in March

• Make box of stuff to send to Mitaka
  • OSEM coils and connectors for assembly.
  • Pico in-air adapter parts.
  • BS soaking cup.
  • Anti-feedthrough adapter parts.
  • Geophone parts?
• Build four geophone assemblies (Okutomi-kun has built five):
  • Have most parts:
    • Four sets of canister parts (body, neck, head).
    • Five geophones.
    • Three circuit boards - probably more exist but need to find.
    • 20 x M8*35 (need 4*16=64)
    • 35 x M8*30 (need 4*8=32)
    • 4 x Viton disks (need 4? or 8?)
    • 123 M8 washers (need 4*24=96)
• Assemble more OSEMs.
  • Have 6 wound coils and connectors at Kamioka (one set, for SR3).
  • Have 6 more at Mitaka.
• Set up SR3 and SRM racks.

  • Miyakawa-san gave us an empty rack for SR3 => can add boxes and do internal cabling and labels.

  • SR3 rack position is decided (on -X,+Y corner of SR3 cleanbooth) => can do in-air cabling from rack to assembly frame.

  • Miyakawa-san will soon give us an empty rack for SRM and decide position => will be able to do set-up.

• Disassemble broken top filters
  • Set up heavy table in SRM area (first floor, -X side).
  • Find jig and blade tensioning screw.
  • Remove blades from #3 (in SRM area).
  • Store #3 in box.
  • Remove floor panel in SRM second floor.
  • Crane #1 (in SR3 area) to SRM area.
  • Remove blades from #1.
  • Put test weights on table.
• BF rebuild - Hirata-san + 1
  • Move BS Test Hang BF to tent and remove blades. (These blades are for BS-BF and will not be used again.)
  • Find SR-BF blades that were removed to free up a BF base for the BS Final Hang.
  • Move BF with tilted keystone to tent and remove blades.
  • Characterize all SR-BF blades and choose two similar groups.
  • Rebuild two filters.
• Etc
  • Move all SFs to cleanbooth and inspect for keystone tilt and/or other issues.
  • Make one set of in-air pico splitter cables (triple and double) for SRM.
  • Make three in-air stepper splitter cables for SR2, SR3 and SRM.
  • Soak the sapphire prisms off the dummy BS for reuse on the SRM metal mass.
  • Do buoyancy calculation (see LIGO-T1100616).
  • Set up SR2 Guardian.
  • Install damping filters for SR2.
• Stuff to have done by other teams
  • Add mushroom top to SRM tank.
  • Put up safety bars