|
Size: 3244
Comment:
|
Size: 3090
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 6: | Line 6: |
| ==== Report for week of 3/13 ==== At Kamioka (Mark, Fabian, Enzo, Perry, Hirata-san): * We took a full set of TFs with the BF stationary but the IRM, IM, RM and TM all hanging. * We marked peeling or damaged areas on the clean booth floor for Furuta-san. * We installed the SF, measuring its weight in the process. * We found the crossbars supporting the SF jacks were too high to allow the SF ring to sit on the pillars while also being partially supported by the jacks. (This was an issue with the 3D CAD - the model of the NB-01 jack had a lower minimum height than reality.) We lowered the crossbars by 5 mm and put thicker spacers (12 mm instead of 3 mm) on top of the jacks supporting the SF and everything worked well. * We installed newly cleaned L-brackets under the BF and SF. * We installed the SF-BF rod and hex cable clamp. * We suspended the BF/IRM/IM/RM/BS section and found it was light, presumably because it had been trimmed according to the Promec measurement of the SF, not Hirata-san's later value. * We added extra ballast mass corresponding to the difference and found the BF section floated at a good height. * We moved trim mass around on the BF until it hung level, and adjusted the IRM and OSEMs until the IRM-IM EQ stops were well-centered and all the OSEMs were centered laterally and mid-range. * We ran 11 extra 20-m in-air cables from the tank towards the rack. (We will need to add 10-m extensions.) * We connected most of the cables to the vacuum flanges with screws and anti-feedthrough adapters. (Some remain to be done.) * We debugged a 900 Hz ringing in the BF LVDT, which turned out to be because the damping was enabled without appropriate filters or gains. * We debugged excess noise in the TM-H3 OSEM, which turned out to be mostly due to a faulty cable. However we worry that some of it may be due to some extensions made of non-vacuum-compatible ribbon cable which we added because the TM-H2 and -H3 OSEM cables are too short. * We found nearly all the parts for the lower breadboard suspension, including the blades, blade bases, associated cable clamps etc. We also found the jigs for installing the blades. ==== Report for week of 3/21 ==== At Kamioka (Mark, Fabian, Enzo, Perry, Hirata-san): * We took a full set of TFs with the SF stationary but the BF, IRM, IM, RM and TM all hanging. * We also did a TF from BF LVDT actuation and confirmed that it was working. * We got SUMCON running on Perry's computer and worked out how to do cut-down versions of Fabian's full Type B model corresponding to the various partial configurations we have data for. |
==== Report for week of 3/5 ==== * Mark finished -v2 of the schedule ([[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7779| L1807779]]). * We removed the non-vacuum-compatible ballast mass from the BS tank. * We secured all the PR2 feedthrough connections with screws. * We grabbed an extra empty rack for SRM and set it up next to the one for SR3 (we will add boxes next week). * We calibrated the SR2 SF LVDT sensing and actuation, and the FR. * We measured the bounce frequencies of the SF with and without the cap, and the bounce frequency of the BF. * We put the SF cap on and lifted and weighed the SF/... section. * However we were unhappy with how the cap had to be forced on and off and how it lowered the load capacity (≈-433 g) and resonance frequency (0.271 Hz-> 0.23 Hz). * We tried the cap left over from B2-3 used in one of the PRs, which was slightly better but still not great. * We measured diameter of the original cap (B2-2) and the new one (B2-3). The original cap was almost exactly 700 mm in internal diameter, and the new one was about 0.2 mm wider. * We moved the filter building bench and tools into the SRM area and started the rebuild of the two remaining BFs (the one from the BS Test Hang and the one with the tilted keystone). * Mark worked on slides for the ASJ and LVC meetings. * The SRM mushroom work was postponed due to other demands on the time of Sawada-san-tachi and Mirapro. |
| Line 28: | Line 21: |
| ==== Plan for coming weeks ==== Next week: * Everyone (Mark, Fabian, Enzo, Perry Hirata-san) at Kamioka, Monday-Friday except for Hirata-san Wednesday-Friday). * Finish SF installation. * Finish BF cabling, hang BF/IRM/IM/RM/BS from SF and confirm weight matches load capacity. * Re-trim BF as necessary. * Get picomotor driver working. Week after next: * Everyone (Mark, Fabian, Enzo, Hirata-san) at Kamioka, Monday-Friday. * Prepare for PI installation. |
==== Plan for week of 3/12 ==== * Shoda-san at Mitaka. * Mark at ASJ (Chiba) Fri, then Mitaka. * Others Kamioka Mon-Thu * F2F VIS Meeting and Farewell Party for Fabian at Mitaka on Friday. * -- * Install boxes in SR3 and SRM racks. * Lay SR3 in-air cabling. * Continue rebuild of BFs. * Ship dummy BS to Mitaka. ==== Plan for week of 3/19 ==== * Fujii-kun and Tanioka-kun join. * Mark at LVC meeting * Fujii-kun at Kamioka * All others at Mitaka * -- * Put four geophones in pods. * Make two sets of IM OSEMs * Make last in-air pico adapter cable * Make three in-air stepper splitter cables for SR2, SR3 and SRM. * Set up Dummy BS prism removal. ==== Plan for week of 3/26 ==== * Mark vacation. * Shoda-san at Mitaka * Others at Kamioka * -- * SF Check * Check load capacity. * Check fit of caps. * Add cable clamps to bases. * Add cable clamps and Cu segments to caps (only if they fit well). * Cable LVDTs and steppers. ==== To-Do Lists, Schedule ==== * [[KAGRA/Subgroups/VIS/TypeB/March2018]] * [[KAGRA/Subgroups/VIS/TypeB/April2018]] * [[KAGRA/Subgroups/VIS/TypeB/ToDoBS]] * [[KAGRA/Subgroups/VIS/TypeB/ToDoSR]] * [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7779|JGW-L1807779-v1 Type B Schedule (SR)]] ==== Vacation Info ==== * Mark at LVC, then vacation, 3/18 (Sun) - 4/1 (Sun) * Hirata-san vacation, Mon 3/5. * Fabian vacation, 3/26-4/27 (then gone). |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Report for week of 3/5
Mark finished -v2 of the schedule (L1807779).
- We removed the non-vacuum-compatible ballast mass from the BS tank.
- We secured all the PR2 feedthrough connections with screws.
- We grabbed an extra empty rack for SRM and set it up next to the one for SR3 (we will add boxes next week).
- We calibrated the SR2 SF LVDT sensing and actuation, and the FR.
- We measured the bounce frequencies of the SF with and without the cap, and the bounce frequency of the BF.
- We put the SF cap on and lifted and weighed the SF/... section.
However we were unhappy with how the cap had to be forced on and off and how it lowered the load capacity (≈-433 g) and resonance frequency (0.271 Hz-> 0.23 Hz).
- We tried the cap left over from B2-3 used in one of the PRs, which was slightly better but still not great.
- We measured diameter of the original cap (B2-2) and the new one (B2-3). The original cap was almost exactly 700 mm in internal diameter, and the new one was about 0.2 mm wider.
- We moved the filter building bench and tools into the SRM area and started the rebuild of the two remaining BFs (the one from the BS Test Hang and the one with the tilted keystone).
- Mark worked on slides for the ASJ and LVC meetings.
- The SRM mushroom work was postponed due to other demands on the time of Sawada-san-tachi and Mirapro.
Plan for week of 3/12
- Shoda-san at Mitaka.
- Mark at ASJ (Chiba) Fri, then Mitaka.
- Others Kamioka Mon-Thu
- F2F VIS Meeting and Farewell Party for Fabian at Mitaka on Friday.
- --
- Install boxes in SR3 and SRM racks.
- Lay SR3 in-air cabling.
- Continue rebuild of BFs.
- Ship dummy BS to Mitaka.
Plan for week of 3/19
- Fujii-kun and Tanioka-kun join.
- Mark at LVC meeting
- Fujii-kun at Kamioka
- All others at Mitaka
- --
- Put four geophones in pods.
- Make two sets of IM OSEMs
- Make last in-air pico adapter cable
- Make three in-air stepper splitter cables for SR2, SR3 and SRM.
- Set up Dummy BS prism removal.
Plan for week of 3/26
- Mark vacation.
- Shoda-san at Mitaka
- Others at Kamioka
- --
- SF Check
- Check load capacity.
- Check fit of caps.
- Add cable clamps to bases.
- Add cable clamps and Cu segments to caps (only if they fit well).
- Cable LVDTs and steppers.
To-Do Lists, Schedule
Vacation Info
- Mark at LVC, then vacation, 3/18 (Sun) - 4/1 (Sun)
- Hirata-san vacation, Mon 3/5.
- Fabian vacation, 3/26-4/27 (then gone).