|
Size: 3153
Comment:
|
Size: 1574
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 7: | Line 7: |
| At Kamioka (Mark, Fabian, Enzo, Perry, Hirata-san): | At Kamioka (Mark, Ohishi-san, Fabian, Enzo, Hirata-san, Yoshioka-kun): * We moved or covered stuff in the BS cleanbooth to prepare for the SR2 crane slot cutting and BS-> SR2 assembly frame move. * We put the service port covers back on at the BF level of the BS tank. * We used the PI jacks to center the bottom of the security structure around the RM. * We debugged a mechanical issue where the #2 IP LVDT had too narrow a gap between the moving and fixed parts, so that there was interference with only a very small clockwise yaw of the IP. We fixed it by moving the bottom baseplate (taking advantage of the fact that it was held by screws in oversize holes for this purpose). * We used the IP FRs to center the IP. * We set the gains on the IP LVDT driver. |
| Line 9: | Line 16: |
| * We counted the used/broken/unused/need cables for Type B. * Hirata-san and Mark installed blades in three LBB blade units. * Hirata-san checked the LBB blade units to see how badly the blade tips were misaligned. The bases will need to be moved towards the clamp end by 21 mm. It is probably not feasible to turn the screw holes into slots, so an adapter part will need to be designed. * We checked that the new in-vacuum geophone cables that Takahashi-san had got for us were the proper new-style ones. (Thus we will need in-air descrambler cables.) * Shoda-san sent Enzo a document by Joris on the tuning of the LVDTs, so he stated working through it. He also researched the specifications of all the coils (PI and SF as well as BF.) * We found the damper magnets and the template for placing the magnets on the ring for the SF. * Hirata-san installed and wired up the PI yaw stepper. The vertical stepper still needs wiring, and the horizontal stepper wiring needs to be made vacuum-compatible. * We installed safety bars on the ±X side of the assembly frame about 3 m off the floor, so they are at waist height for a person standing on one of the tall ladders. The one on the +X side will be very good for safety where it is, but the one on the -X side will need re-doing: it is too close and not very securely attached because of interference from vacuum pump cabling. * We unlocked the inverted pendulum and experimented with adding weight. It was still stable with 4 layers of arc weights. * We also experimented with getting both the IP centered and the security structure vertical (so that the suspension hang centrally within it). We managed to get it all right with a combination of leveling the PI with the jacks and moving the IP with the fishing rods. * Adjusting the verticality of the SS had left the bottom of it off-center in the assembly frame, so we picked the entire system up with the crane and moved it in +Y and -X a few mm to re-center it. * We started to remove the PI so we could do various adjustments (check the SF LVDT, reconfigure the Cu damper, add the hex cable clamp on the rod and hang the magnet disk for the SF damper) but gave up when the PI-SF jammed in the SF. |
==== Plan for week of 10/2 ==== Kamioka: Mark, Enzo (Tue-Fri), Ohishi-san, Kozu-kun. * Finish preparation for SR2 work. * Debug electronics, especially actuation. * Tune IP, do LVDT/stepper calibration. * Remove First Contact, try OL. Mitaka: Fabian, Hirata-san * Design ballast for LBB. * Design improved PI yaw adjustment. * SR procurement. |
| Line 22: | Line 27: |
| ==== Plan for week of 10/10 ==== Holiday Mon 10/9, Open Day prep Fri 10/13.<<BR>> * TFs, final preparation for alignment in week of 10/16. |
|
| Line 23: | Line 31: |
| ==== Plan for coming weeks ==== For more detail, see [[KAGRA/Subgroups/VIS/TypeB/ToDo]]. |
==== Plan for week of 10/16 ==== Kamioka: all but Mark * Work with alignment team. |
| Line 26: | Line 35: |
| Week of 5/15: * Enzo from Tuesday 5/16 (driving test), rest of team from Monday. * Fix PI-SF rod jamming. * Remove PI and SF cap. * Continue debugging SF LVDT. * Reconfigure Cu damper ring on SF. * Add magnets to upper SF damper ring. * Add cable clamps on the PI (a few places are inaccessible when the PI is on the assembly frame). * Reinstall PI, this time with rods and damper ring. * Reinstall PI-SF rod, this time with hex cable clamp. * Prepare for PR2 bellows removal on 5/15 (move table with tools). * Cable/test PI horizontal LVDTs and steppers. * Install/cable/test geophones. |
==== Vacation Info ==== Mark: 10/16-24 |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Past week report
At Kamioka (Mark, Ohishi-san, Fabian, Enzo, Hirata-san, Yoshioka-kun):
We moved or covered stuff in the BS cleanbooth to prepare for the SR2 crane slot cutting and BS-> SR2 assembly frame move.
- We put the service port covers back on at the BF level of the BS tank.
- We used the PI jacks to center the bottom of the security structure around the RM.
- We debugged a mechanical issue where the #2 IP LVDT had too narrow a gap between the moving and fixed parts, so that there was interference with only a very small clockwise yaw of the IP. We fixed it by moving the bottom baseplate (taking advantage of the fact that it was held by screws in oversize holes for this purpose).
- We used the IP FRs to center the IP.
- We set the gains on the IP LVDT driver.
Plan for week of 10/2
Kamioka: Mark, Enzo (Tue-Fri), Ohishi-san, Kozu-kun.
- Finish preparation for SR2 work.
- Debug electronics, especially actuation.
- Tune IP, do LVDT/stepper calibration.
- Remove First Contact, try OL.
Mitaka: Fabian, Hirata-san
- Design ballast for LBB.
- Design improved PI yaw adjustment.
- SR procurement.
Plan for week of 10/10
Holiday Mon 10/9, Open Day prep Fri 10/13.
- TFs, final preparation for alignment in week of 10/16.
Plan for week of 10/16
Kamioka: all but Mark
- Work with alignment team.
Vacation Info
Mark: 10/16-24