|
Size: 2349
Comment:
|
Size: 2929
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 7: | Line 7: |
| At Kamioka (Mark, Enzo, Simon, Type Bp team): * Mark remade the BF pico adapter cable which was poorly made and had also been damaged. * The Type Bp team tided up the BS rack and made new labels for many cables (thanks!). * Enzo connected up the in-air cables for the picos and steppers. * Mark and Enzo renumbered the PI LVDTs, geophones and LVDTs to make a consistent scheme working anticlockwise. * Enzo and Mark debugged all the cables. The only problem we couldn't solve was that the actuator coil for PI LVDT #0 is open-circuit at the connector on the LVDT. (It has been intermittent but worked before the craning.) We may have to redo the connector or replace the LVDT. Limited TFs will be possible in the next week. * Simon set up the LSOL and was easily able to get a return beam from the mirror on the dummy BS. * Shoda-san copied over the LSOL section of the PR3 real-time model into the BS model and made other improvements (thanks!). * Mark brought home |
|
| Line 17: | Line 8: |
| At Mitaka (Fabian, Hirata-san): * Fabian finished designing final trim masses for IM/BF/SF for the final hang of the BS and passed it to Hirata-san to make drawings and get quotes. * Hirata-san requested quotes for the replaceable-jaw version of the BS wire clamps. * Fabian and Hirata-san gathered needed items for the BS prism/flag gluing. * Hirata-san designed receptacles for the new rods with 8 mm heads and requested quotes. |
* Mark finished the OL calibration/diagonalization calculation and wrote it up as klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=3835|3835]] and [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7205| T1707205-v4]]. * We glued the prisms and magnets on the SR2. * We got Miyo-kun to set up the SR2-IM pico driver and tested it and the picos that will be used in the IM. * We weighed the BF for the SR2. * Enzo put DIO cards in the IO chassis and cabled them to the coil drivers. * Enzo found more of the in-vacuum cables that will be needed for SR2. Only a few remain to be found. * Enzo and Shoda-san installed the vacuum-feedthroughs on the assembly frame and routed many of the in-air cables. * Hirata-san and Mark moved the PR/SR trolley system from SR3 to SR2, reconfigured the top of the assembly frame and checked the crossbar heights. (Everything was quite close to the drawing, but a few small adjustments up/down will be required.) * Fabian found an issue with the IM: we have two of the upper movable masses and no lower ones. Probably one of the PRs has been built with two lower masses. Unfortunately an upper mass has an extra hole in an inconvenient place and can't be used as a lower mass. Hirata-san ordered a suitable plug part from Misumi, and Fabian washed it and glued it in with EP30. * Fabian assembled the RM and test-assembled the IRM. (The IRM will have to be partly disassembled during installation.) * Shoda-san and Enzo got all the control loops working on the BS, and worked with Izumi-san to steer the beam down the Y-arm. They found the passive damping was not working very well, even after correcting a 1.5 mm height error in F0. We may need to lower the damper ring. * Shoda-san created a BS Guardian. * We got Yamamoto-san to connect up the SR2 rack and create an SR2 real-time model. |
| Line 23: | Line 22: |
| ==== Plan for week of 7/3 ==== * Do prism/flag gluing on real BS at Kashiwa (whole team). * Do new 3D CAD (Hirata-san): * SR2 on BS assembly frame. (Adjust jack positions if possible, or leave for Fabian/Mark to do.) * Final BS build, SS/PI/SF as for Test Hang but with BF/IRM/IM/BS/RM down rotated back to original direction. * On-assembly-frame version. (Adjust jack positions if possible, or leave for Mark to do.) * In-tank version. * Solve arc weight versus magic wand problem. * Do mass budget for LBB - design ballast masses (Fabian) * Run TFs, make improvements to real-time model (Mark, Enzo). ==== Plan for week of 7/10 ==== Mark and Enzo at Kamioka: * Fix broken LVDT actuator coil. * Test picos and steppers more fully. |
==== Plan for week of 12/18 ==== * Shoda-san vacation * Mark, Fabian, Enzo, Kozu-kun at Kamioka Mon-Wed. * Find plumb bob. * Assembly frame alignment and optical table centering. (Mark and Hirata) * Finish IM assembly and pico test. (Fabian and Enzo) * Do inventory of ballast masses. (Fabian) ==== Plan for week of 12/25 ==== * Mark, Enzo, Fabian vacation * Shoda-san, Kozu-kun, Hirata-san at Kamioka Mon-Thu. * Install IM ring interface blocks and IM ring. * Install new jack receptacles (in SR3 area, second floor) on load gauge adapter (SR2 area, second floor). (Hirata-san) * OL setup. ==== Plan for week of 1/9 ==== * Mark, Fabian, Enzo, Shoda-san at Kamioka Tue-Fri. * Hang SR and RM. ==== Vacation Info ==== * Mark 12/22-1/3 * Enzo, 12/21-12/27 (but ''not'' 12/28) * Fabian 12/22-1/5 * Hirata-san 12/21-22 (conference) * Shoda-san 12/18-21 |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Past week report
Mark finished the OL calibration/diagonalization calculation and wrote it up as klog 3835 and T1707205-v4.
- We glued the prisms and magnets on the SR2.
- We got Miyo-kun to set up the SR2-IM pico driver and tested it and the picos that will be used in the IM.
- We weighed the BF for the SR2.
- Enzo put DIO cards in the IO chassis and cabled them to the coil drivers.
- Enzo found more of the in-vacuum cables that will be needed for SR2. Only a few remain to be found.
- Enzo and Shoda-san installed the vacuum-feedthroughs on the assembly frame and routed many of the in-air cables.
- Hirata-san and Mark moved the PR/SR trolley system from SR3 to SR2, reconfigured the top of the assembly frame and checked the crossbar heights. (Everything was quite close to the drawing, but a few small adjustments up/down will be required.)
- Fabian found an issue with the IM: we have two of the upper movable masses and no lower ones. Probably one of the PRs has been built with two lower masses. Unfortunately an upper mass has an extra hole in an inconvenient place and can't be used as a lower mass. Hirata-san ordered a suitable plug part from Misumi, and Fabian washed it and glued it in with EP30.
- Fabian assembled the RM and test-assembled the IRM. (The IRM will have to be partly disassembled during installation.)
- Shoda-san and Enzo got all the control loops working on the BS, and worked with Izumi-san to steer the beam down the Y-arm. They found the passive damping was not working very well, even after correcting a 1.5 mm height error in F0. We may need to lower the damper ring.
- Shoda-san created a BS Guardian.
- We got Yamamoto-san to connect up the SR2 rack and create an SR2 real-time model.
Plan for week of 12/18
- Shoda-san vacation
- Mark, Fabian, Enzo, Kozu-kun at Kamioka Mon-Wed.
- Find plumb bob.
- Assembly frame alignment and optical table centering. (Mark and Hirata)
- Finish IM assembly and pico test. (Fabian and Enzo)
- Do inventory of ballast masses. (Fabian)
Plan for week of 12/25
- Mark, Enzo, Fabian vacation
- Shoda-san, Kozu-kun, Hirata-san at Kamioka Mon-Thu.
- Install IM ring interface blocks and IM ring.
- Install new jack receptacles (in SR3 area, second floor) on load gauge adapter (SR2 area, second floor). (Hirata-san)
- OL setup.
Plan for week of 1/9
- Mark, Fabian, Enzo, Shoda-san at Kamioka Tue-Fri.
- Hang SR and RM.
Vacation Info
- Mark 12/22-1/3
Enzo, 12/21-12/27 (but not 12/28)
- Fabian 12/22-1/5
- Hirata-san 12/21-22 (conference)
- Shoda-san 12/18-21