|
Size: 954
Comment:
|
Size: 2556
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 5: | Line 5: |
| * Type B Past Week Summary * Fabian did inventory of parts/fasteners for dummy BS, RM, IM and IRM - almost all at Mitaka. A handful (picos, pico drivers) will be brought back from Kamioka. * Fabian continued work on Mathematica and Matlab models of the BS and control system. He now gets much better agreement after correcting discrepancies between the parameter sets. * Hirata-san worked on organizing: * Checking Mirapro assembly frame drawings * Ordering missing screws and small items (screws for dummy mass, fine pitch M8 for RM) * Work platforms and clean booth second floor arrangement. * Load gauge adapter and associated parts * Possible fall-back plans for the rods connecting the security structure to the PI. * Design for additional trim masses (existing design had no provision for adding/removing). |
=== Type B (Mark) === ==== Past week report ==== At Kamioka (Mark, Enzo, Simon, Type Bp team): * Mark remade the BF pico adapter cable which was poorly made and had also been damaged. * The Type Bp team tided up the BS rack and made new labels for many cables (thanks!). * Enzo connected up the in-air cables for the picos and steppers. * Mark and Enzo renumbered the PI LVDTs, geophones and LVDTs to make a consistent scheme working anticlockwise. * Enzo and Mark debugged all the cables. The only problem we couldn't solve was that the actuator coil for PI LVDT #0 is open-circuit at the connector on the LVDT. (It has been intermittent but worked before the craning.) We may have to redo the connector or replace the LVDT. Limited TFs will be possible in the next week. * Simon set up the LSOL and was easily able to get a return beam from the mirror on the dummy BS. * Shoda-san copied over the LSOL section of the PR3 real-time model into the BS model and made other improvements (thanks!). * Mark brought home At Mitaka (Fabian, Hirata-san): * Fabian finished designing final trim masses for IM/BF/SF for the final hang of the BS and passed it to Hirata-san to make drawings and get quotes. * Hirata-san requested quotes for the replaceable-jaw version of the BS wire clamps. * Fabian and Hirata-san gathered needed items for the BS prism/flag gluing. * Hirata-san designed receptacles for the new rods with 8 mm heads and requested quotes. ==== Plan for week of 7/3 ==== * Do prism/flag gluing on real BS at Kashiwa (whole team). * Do new 3D CAD (Hirata-san): * SR2 on BS assembly frame. (Adjust jack positions if possible, or leave for Fabian/Mark to do.) * Final BS build, SS/PI/SF as for Test Hang but with BF/IRM/IM/BS/RM down rotated back to original direction. * On-assembly-frame version. (Adjust jack positions if possible, or leave for Mark to do.) * In-tank version. * Solve arc weight versus magic wand problem. * Do mass budget for LBB - design ballast masses (Fabian) * Run TFs, make improvements to real-time model (Mark, Enzo). ==== Plan for week of 7/10 ==== Mark and Enzo at Kamioka: * Fix broken LVDT actuator coil. * Learn how Miyo-kun's pico driver software works and make improvements. * Test picos and steppers more fully. * Finish tidying rack and labeling cables. Fabian and Hirata-san at Mitaka. * Design SR assembly frame. * Inventory for SR. |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Past week report
At Kamioka (Mark, Enzo, Simon, Type Bp team):
- Mark remade the BF pico adapter cable which was poorly made and had also been damaged.
- The Type Bp team tided up the BS rack and made new labels for many cables (thanks!).
- Enzo connected up the in-air cables for the picos and steppers.
- Mark and Enzo renumbered the PI LVDTs, geophones and LVDTs to make a consistent scheme working anticlockwise.
- Enzo and Mark debugged all the cables. The only problem we couldn't solve was that the actuator coil for PI LVDT #0 is open-circuit at the connector on the LVDT. (It has been intermittent but worked before the craning.) We may have to redo the connector or replace the LVDT. Limited TFs will be possible in the next week.
- Simon set up the LSOL and was easily able to get a return beam from the mirror on the dummy BS.
- Shoda-san copied over the LSOL section of the PR3 real-time model into the BS model and made other improvements (thanks!).
- Mark brought home
At Mitaka (Fabian, Hirata-san):
- Fabian finished designing final trim masses for IM/BF/SF for the final hang of the BS and passed it to Hirata-san to make drawings and get quotes.
- Hirata-san requested quotes for the replaceable-jaw version of the BS wire clamps.
- Fabian and Hirata-san gathered needed items for the BS prism/flag gluing.
- Hirata-san designed receptacles for the new rods with 8 mm heads and requested quotes.
Plan for week of 7/3
- Do prism/flag gluing on real BS at Kashiwa (whole team).
- Do new 3D CAD (Hirata-san):
- SR2 on BS assembly frame. (Adjust jack positions if possible, or leave for Fabian/Mark to do.)
- Final BS build, SS/PI/SF as for Test Hang but with BF/IRM/IM/BS/RM down rotated back to original direction.
- On-assembly-frame version. (Adjust jack positions if possible, or leave for Mark to do.)
- In-tank version.
- Solve arc weight versus magic wand problem.
- Do mass budget for LBB - design ballast masses (Fabian)
- Run TFs, make improvements to real-time model (Mark, Enzo).
Plan for week of 7/10
Mark and Enzo at Kamioka:
- Fix broken LVDT actuator coil.
- Learn how Miyo-kun's pico driver software works and make improvements.
- Test picos and steppers more fully.
- Finish tidying rack and labeling cables.
Fabian and Hirata-san at Mitaka.
- Design SR assembly frame.
- Inventory for SR.