|
Size: 2843
Comment:
|
Size: 2929
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 7: | Line 7: |
| At Kamioka (Mark, Enzo, Hirata-san, Yoshioka-kun): * We disassembled the suspension. * We removed all the cables and bagged and labelled them for reuse. * The PI is parked on the pallet. * The SF was initially parked between the frame and tank and then manhandled to one side. The same procedure was used for the SF ring. * The BF was parked between the assembly frame and tank. The BF ring was stored in the top of the structure. * We removed various useful and no-longer-needed items from the BF, including the lower rod receptacle, thrust bearing, fishing rod and temporary ballast masses. * We cut the wires and removed the RM and dummy BS on the RM trolley. * The wire clamps were moderately deeply scarred and could probably be reused, but we plan to use the new set, which will be available on Tuesday of next week. * We discovered that the problem with the old BF was due to the fishing rod, which had not had a pair of lock nuts and had been damaged by being drive too high, so that the springs hit the underside of the cap and were bent at the base. We will install lock nuts and set them to the correct height for the final installation. * The gluing of the BS primary prisms and magnets went well, but we had to reglue the secondary prisms because they stuck to the jigs and were pulled off when the jigs were retracted. The second try went well and the BS is ready for use. * Fabian and Hirata-san characterized 7 new BS BF blades. There was one outlier but the rest were in a tight group. * Hirata-san used 3 of the new blades to build a new BF. * Miyo-kun and others from the Type Bp team did a lot of tidying up of the BS rack for us, and removed a lot of in-air cables running through the cleanbooth. When he returns, on 8/8, Enzo will coordinate relaying the cables in the cable trays (which were not installed when the initial cabling was done). |
|
| Line 22: | Line 8: |
| * Mark finished the OL calibration/diagonalization calculation and wrote it up as klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=3835|3835]] and [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7205| T1707205-v4]]. * We glued the prisms and magnets on the SR2. * We got Miyo-kun to set up the SR2-IM pico driver and tested it and the picos that will be used in the IM. * We weighed the BF for the SR2. * Enzo put DIO cards in the IO chassis and cabled them to the coil drivers. * Enzo found more of the in-vacuum cables that will be needed for SR2. Only a few remain to be found. * Enzo and Shoda-san installed the vacuum-feedthroughs on the assembly frame and routed many of the in-air cables. * Hirata-san and Mark moved the PR/SR trolley system from SR3 to SR2, reconfigured the top of the assembly frame and checked the crossbar heights. (Everything was quite close to the drawing, but a few small adjustments up/down will be required.) * Fabian found an issue with the IM: we have two of the upper movable masses and no lower ones. Probably one of the PRs has been built with two lower masses. Unfortunately an upper mass has an extra hole in an inconvenient place and can't be used as a lower mass. Hirata-san ordered a suitable plug part from Misumi, and Fabian washed it and glued it in with EP30. * Fabian assembled the RM and test-assembled the IRM. (The IRM will have to be partly disassembled during installation.) * Shoda-san and Enzo got all the control loops working on the BS, and worked with Izumi-san to steer the beam down the Y-arm. They found the passive damping was not working very well, even after correcting a 1.5 mm height error in F0. We may need to lower the damper ring. * Shoda-san created a BS Guardian. * We got Yamamoto-san to connect up the SR2 rack and create an SR2 real-time model. |
|
| Line 23: | Line 22: |
| ==== Plan for week of 7/31 ==== Kamioka: Mark (Mon-Fri), Fabian (Mon-Wed), Hirata-san (Tue-Thu), Yoshioka-kun (Tue, Wed, Fri) <<BR>> Mitaka: Hirata-san (Mon, Fri)<<BR>> Enzo: vacation * Recheck alignment of assembly frame and centering of optical table. * Install IM, suspend BS and RM. * Remove LBB rings (time permitting). |
==== Plan for week of 12/18 ==== * Shoda-san vacation * Mark, Fabian, Enzo, Kozu-kun at Kamioka Mon-Wed. * Find plumb bob. * Assembly frame alignment and optical table centering. (Mark and Hirata) * Finish IM assembly and pico test. (Fabian and Enzo) * Do inventory of ballast masses. (Fabian) |
| Line 31: | Line 30: |
| ==== Plan for week of 8/7 ==== Site closure: Friday<<BR>> Kamioka: Mark (Mon-Thu), Enzo (Tue-Thu), Yoshioka-kun (Tue, Wed), Ohishi (TBD). Mitaka: Hirata-san (Mon-Fri) Vacation: Enzo (Mon), Fabian (Thu, Fri) * Weigh/trim BS/RM/IM. * Take out old BF; bring in rebuilt BF. * Suspend BS/RM/IM, add IRM. * Lay new in-air OSEM cables. |
==== Plan for week of 12/25 ==== * Mark, Enzo, Fabian vacation * Shoda-san, Kozu-kun, Hirata-san at Kamioka Mon-Thu. * Install IM ring interface blocks and IM ring. * Install new jack receptacles (in SR3 area, second floor) on load gauge adapter (SR2 area, second floor). (Hirata-san) * OL setup. |
| Line 41: | Line 37: |
| Vacation Info: Enzo: Sat 7/22 through Sun 8/6 Fabian: Fri 8/4 through Mon 8/21 Mark: TBD Mid-Oct |
==== Plan for week of 1/9 ==== * Mark, Fabian, Enzo, Shoda-san at Kamioka Tue-Fri. * Hang SR and RM. ==== Vacation Info ==== * Mark 12/22-1/3 * Enzo, 12/21-12/27 (but ''not'' 12/28) * Fabian 12/22-1/5 * Hirata-san 12/21-22 (conference) * Shoda-san 12/18-21 |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Past week report
Mark finished the OL calibration/diagonalization calculation and wrote it up as klog 3835 and T1707205-v4.
- We glued the prisms and magnets on the SR2.
- We got Miyo-kun to set up the SR2-IM pico driver and tested it and the picos that will be used in the IM.
- We weighed the BF for the SR2.
- Enzo put DIO cards in the IO chassis and cabled them to the coil drivers.
- Enzo found more of the in-vacuum cables that will be needed for SR2. Only a few remain to be found.
- Enzo and Shoda-san installed the vacuum-feedthroughs on the assembly frame and routed many of the in-air cables.
- Hirata-san and Mark moved the PR/SR trolley system from SR3 to SR2, reconfigured the top of the assembly frame and checked the crossbar heights. (Everything was quite close to the drawing, but a few small adjustments up/down will be required.)
- Fabian found an issue with the IM: we have two of the upper movable masses and no lower ones. Probably one of the PRs has been built with two lower masses. Unfortunately an upper mass has an extra hole in an inconvenient place and can't be used as a lower mass. Hirata-san ordered a suitable plug part from Misumi, and Fabian washed it and glued it in with EP30.
- Fabian assembled the RM and test-assembled the IRM. (The IRM will have to be partly disassembled during installation.)
- Shoda-san and Enzo got all the control loops working on the BS, and worked with Izumi-san to steer the beam down the Y-arm. They found the passive damping was not working very well, even after correcting a 1.5 mm height error in F0. We may need to lower the damper ring.
- Shoda-san created a BS Guardian.
- We got Yamamoto-san to connect up the SR2 rack and create an SR2 real-time model.
Plan for week of 12/18
- Shoda-san vacation
- Mark, Fabian, Enzo, Kozu-kun at Kamioka Mon-Wed.
- Find plumb bob.
- Assembly frame alignment and optical table centering. (Mark and Hirata)
- Finish IM assembly and pico test. (Fabian and Enzo)
- Do inventory of ballast masses. (Fabian)
Plan for week of 12/25
- Mark, Enzo, Fabian vacation
- Shoda-san, Kozu-kun, Hirata-san at Kamioka Mon-Thu.
- Install IM ring interface blocks and IM ring.
- Install new jack receptacles (in SR3 area, second floor) on load gauge adapter (SR2 area, second floor). (Hirata-san)
- OL setup.
Plan for week of 1/9
- Mark, Fabian, Enzo, Shoda-san at Kamioka Tue-Fri.
- Hang SR and RM.
Vacation Info
- Mark 12/22-1/3
Enzo, 12/21-12/27 (but not 12/28)
- Fabian 12/22-1/5
- Hirata-san 12/21-22 (conference)
- Shoda-san 12/18-21