|
Size: 2458
Comment:
|
Size: 2665
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 6: | Line 6: |
| ==== Report for week of 2/26 ==== * We routed all the cables from the BF level up via the flying saucer to the SF. * Hirata-san tried filing the SF cap to improve the fit, but without much success. * Hirata-san installed the Cu segments and cable clamps on the SF cap and the SF LVDT and FR cables. * We cabled and tested the BF cap picos and the SF LVDT and FR. (The LVDT still needs a full calibration.) * We worked on recovering the IM OSEM alignment. |
==== Report for week of 6/18 ==== * We powered down the Type B racks as a precaution against possible loss of power during work on Tuesday, and later powered them up again. * We put a flange cover over the hole in the floor near the filter tuning area as a temporary safety measure. We later managed to entirely close the part of the hole that was not covered by the filter, by moving the filter towards the outside and using short floor panels from SR2 on the tank side. * We removed the SR3 PI from the filter tuning area and brought in the SR2 one. * We put magnets on the SR damper magnet ring to match the two Cu segments we were using. * We craned the SR3 PI into the AF, connected it to the security structure, and hooked the SF/... section and the SF damper magnet ring. * At first the F0 did not rise, and we realized that we had 2 kg less margin than we originally thought because we had not allowed for the PI-SF rod receptacle, the top disk which holds the yaw stepper mechanism, or the stepper itself. * However we were able to try the redesigned PI fishing rod, parts for which had just arrived. The optional strong CuBe spring in the new arrangement gave plenty of extra lift, so that we now have about 5 kg of margin. We did have to move the yoke to work around the problem that the CuBe spring tends to tilt the keystone, but we got it moving freely. We will also have to compress the blades some more to compensate for the extra stiffness, which caused the frequency to rise from 0.5 Hz to 0.9 Hz. |
| Line 13: | Line 15: |
| ==== Plan for week of 3/5 ==== * Shoda-san at Mitaka. * Hirata-san vacation Mon 3/5, then Kamioka * Others at Kamioka. * - * '''Remove LBB temporary ballast masses from BS chamber.''' * Finish recovering IM OSEM alignment. * Calibrate SF LVDT. * Lift SF/... section and check total mass and balance. * Get SRM tank mushroom section installed (Hirata-san, Kimura-san) * Set up for rebuilding of two BFs. |
|
| Line 25: | Line 16: |
| ==== Plan for week of 3/12 ==== * Shoda-san at Mitaka. * Mark at ASJ (Chiba) Fri, then Mitaka. * Hirata-san vacation Mon 3/5; Kamioka Tue-Thu; Mitaka Fri * Others Kamioka Mon-Thu * Install boxes in SR3 and SRM racks. * Lay SR3 in-air cabling. * Continue rebuild of BFs. |
==== Plan for week of 7/2 ==== * Mark, Hirata-san, Terrence at Kamioka Mon-Fri. * Enzo at Kamioka Mon-Wed. * Kozu-kun at Kamioka except Wed. * -- * Continued tuning of filter in PI #3 for SR3. * Building and tuning of filter in PI #1 for SR2 (time permitting). * Lots of cable routing and testing. * Install geophones and arc weights. |
| Line 34: | Line 26: |
| ==== Plan for week of 3/19 ==== * Mark at LVC meeting * All others at Mitaka * Make two sets of IM OSEMs * Make last in-air pico adapter cable * Make three in-air stepper splitter cables for SR2, SR3 and SRM. * Set up Dummy BS prism removal. ==== Plan for week of 3/26 ==== * Mark vacation. * Shoda-san at Mitaka * Others at Kamioka |
==== Plan for week of 7/9 ==== * Mark, Enzo, Hirata-san, Kozu-kun, Terrence at Kamioka Mon-Fri. |
| Line 47: | Line 29: |
| * F0 Prototype Blade Test * Characterize blades. * Choose best set of three. * Remove cracked blades from filter in SRM area. * Set up test weights in SRM area, first floor. * Remove floor panel in SRM area, second floor. * Install chosen blades. * Measure load capacity. |
* Lock suspension. * Remove tank lid and raise LBB damper rings. * Crane suspension into tank. |
| Line 57: | Line 34: |
| * [[KAGRA/Subgroups/VIS/TypeB/March2018]] * [[KAGRA/Subgroups/VIS/TypeB/April2018]] |
|
| Line 61: | Line 36: |
| * [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7779|JGW-L1807779-v1 Type B Schedule (SR)]] | * [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7779|JGW-L1807779 Type B Schedule (SR)]] |
| Line 64: | Line 39: |
| * Mark at LVC, then vacation, 3/18 (Sun) - 4/1 (Sun) * Hirata-san vacation, Mon 3/5. * Fabian vacation, 3/26-4/27 (then gone). |
* Kozu-kun: 7/4 Tokyo. * Enzo: 7/5-6 NAOJ Party, Mitaka. * Terrence: 8/24-26 f2f, then returns to Hong Kong. * Enzo: 9/14 JPS, 9/15 through 10/18 vacation in Chile. |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Report for week of 6/18
- We powered down the Type B racks as a precaution against possible loss of power during work on Tuesday, and later powered them up again.
- We put a flange cover over the hole in the floor near the filter tuning area as a temporary safety measure. We later managed to entirely close the part of the hole that was not covered by the filter, by moving the filter towards the outside and using short floor panels from SR2 on the tank side.
- We removed the SR3 PI from the filter tuning area and brought in the SR2 one.
- We put magnets on the SR damper magnet ring to match the two Cu segments we were using.
- We craned the SR3 PI into the AF, connected it to the security structure, and hooked the SF/... section and the SF damper magnet ring.
- At first the F0 did not rise, and we realized that we had 2 kg less margin than we originally thought because we had not allowed for the PI-SF rod receptacle, the top disk which holds the yaw stepper mechanism, or the stepper itself.
However we were able to try the redesigned PI fishing rod, parts for which had just arrived. The optional strong CuBe spring in the new arrangement gave plenty of extra lift, so that we now have about 5 kg of margin. We did have to move the yoke to work around the problem that the CuBe spring tends to tilt the keystone, but we got it moving freely. We will also have to compress the blades some more to compensate for the extra stiffness, which caused the frequency to rise from 0.5 Hz to 0.9 Hz.
Plan for week of 7/2
- Mark, Hirata-san, Terrence at Kamioka Mon-Fri.
- Enzo at Kamioka Mon-Wed.
- Kozu-kun at Kamioka except Wed.
- --
- Continued tuning of filter in PI #3 for SR3.
- Building and tuning of filter in PI #1 for SR2 (time permitting).
- Lots of cable routing and testing.
- Install geophones and arc weights.
Plan for week of 7/9
- Mark, Enzo, Hirata-san, Kozu-kun, Terrence at Kamioka Mon-Fri.
- --
- Lock suspension.
- Remove tank lid and raise LBB damper rings.
- Crane suspension into tank.
To-Do Lists, Schedule
Vacation Info
- Kozu-kun: 7/4 Tokyo.
- Enzo: 7/5-6 NAOJ Party, Mitaka.
- Terrence: 8/24-26 f2f, then returns to Hong Kong.
- Enzo: 9/14 JPS, 9/15 through 10/18 vacation in Chile.