|
Size: 2208
Comment:
|
Size: 3427
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 6: | Line 6: |
| ==== Report for week of 4/9 ==== * Mark glued prisms and magnet/standoff assemblies on the SR3. The SR3 needed to be raised in the box by 0.7 mm to make the prisms go on at the right height, which was done using M4 washers under the PEEK feet. * Mark glued ferromagnetic disks on the last 5 IM flags. This completes 2 sets, for SR3 and SRM. * Mark configured two pico motor drivers ordered by Takahashi-san as SR3-IM and SRM-BF. * Enzo and Kozu-kun finished preparing and calibrating the SF and BF for SR3 and almost entirely finished with those for SRM. * Hirata-san worked on building two IMs for SR3 and SRM. The SR3 one just needs to have flags attached and to be weighed; the SRM needs another few hours work. * Shoda-san worked on the design of the metal SRM, on the LBB ballast mass, and on the plans for testing the BS in bKAGRA Phase 1. |
==== Report for week of 5/7 ==== * We inspected the wires and clamps involved in the wire break. * The scars on the clamp on the tungsten wire that failed had very different depths, with the one that failed being much deeper, so probably the clamp piece was not completely straight before tensioning. However one wire on the other side was also badly crushed and on the point of failing, so the tension was clearly too much. * We decided on new torque specs of 2 N.m for the primary clamps (down from 5 N.m) and 10 N.m (down from 20 N.m) for the secondary. The secondary clamp spec, for M6 screws, is now based on the LIGO policy of using the maximum suggested for the screw and the LIGO value for a coated 1/4-20 screw (100 in-lb = 11.3 N.m), and the primary clamp spec is derated by 2/3 from the spec for an M5 screw because the clamp pieces are recessed and only grip the wire at narrow sections along the edges, concentrating the force. * None of the screws showed any signs of damage. * All of the scars on the primary clamps were shallow enough that could reuse the clamp pieces. The tungsten secondary clamps were never tightened, and the outer pieces of piano wire secondary clamps were badly scarred but could be reused upside down. * We successfully rehung the SR3 and RM. In the process we noticed and fixed an issue with the assembly frame (due to an out-of-date number in the Mirapro diagram, the IM crossbars were set 3 mm too high, which would have affected the wire length). * We added the sections of the security structure below the RM and up to the BF. * We installed the TM OSEM cables and routed them up to the IM. * We installed the load gauge adapter and load gauge and prepared the IM/... section for weighing. * We removed the three cracked F0 blades from the PI #3 in the SRM, and prepared for testing prototype new blades in that PI. We removed a floor panel under the PI and set up the filter service trolley underneath it with a stack of masses for a dummy load. * Mirapro installed the SRM mushroom. |
| Line 14: | Line 19: |
| ==== Plan for week of 4/16 ==== * Shoda-san, Fujii-kun at Mitaka * Tanioka-san at Kamioka Tue-Thu * Others at Kamioka full week * -- * Move SF and BF for SRM out of the way. * Check results of gluing. * Build 1xRM * Calibrate OSEMs. * Start SR3 Hang * Reset assembly frame crossbars to correct heights. * Center the optical table. * Align the assembly frame vertically. * Install IM ring and IM. * Hang optic. * Hang RM. * Cable RM OSEMs. |
==== Plan for week of 5/14 ==== * Mark, Enzo, Hirata-san, Kozu-kun at Kamioka Mon-Thu, then Osaka. * Weigh IM/... section. * Characterize F0 blade prototypes. * Remove F0 blade prototypes (and send for rework if necessary). * Start characterizing LBB blades. * Crane in BF. * Add IRM top plate, maraging rod, flying saucer. * Suspend IM, check pitch, roll and vertical, adjust trim mass. * Cable and (re-)test TM OSEMs, IM picos, BF yaw pico, BF LVDT and FR. |
| Line 32: | Line 30: |
| ==== Plan for week of 4/23 ==== * Shoda-san, Tanioka-san at Mitaka * Hirata-san at Mitaka * Mark, Enzo, Fujii-kun, Kozu-kun at Kamioka * -- * Clean parts (cable clamp bases, etc, etc). * Observe KAGRA Phase 1 operations, assist if problems arise. * Continue SR3 hang. |
==== Plan for week of 5/21 ==== * Mark, Enzo, Hirata-san, Kamioka Mon-Fri. * Kozu-kun at Kamioka Wed-Fri. * Install IRM sides, and IM OSEMs. * Center IM OSEMs (in/out and laterally) * Route all cables to underneath BF. * Add BF internal ballast mass. * Add BF cap. |
| Line 41: | Line 39: |
| ==== Plan for week of 4/30 ==== * Golden Week! |
==== Plan for week of 5/28 ==== * Mark, Enzo, Hirata-san, Kamioka Mon-Fri. * Kozu-kun at Kamioka Mon only. * TBD. |
| Line 52: | Line 51: |
| * Fabian vacation, 3/26-4/27 (then gone). |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Report for week of 5/7
- We inspected the wires and clamps involved in the wire break.
- The scars on the clamp on the tungsten wire that failed had very different depths, with the one that failed being much deeper, so probably the clamp piece was not completely straight before tensioning. However one wire on the other side was also badly crushed and on the point of failing, so the tension was clearly too much.
- We decided on new torque specs of 2 N.m for the primary clamps (down from 5 N.m) and 10 N.m (down from 20 N.m) for the secondary. The secondary clamp spec, for M6 screws, is now based on the LIGO policy of using the maximum suggested for the screw and the LIGO value for a coated 1/4-20 screw (100 in-lb = 11.3 N.m), and the primary clamp spec is derated by 2/3 from the spec for an M5 screw because the clamp pieces are recessed and only grip the wire at narrow sections along the edges, concentrating the force.
- None of the screws showed any signs of damage.
- All of the scars on the primary clamps were shallow enough that could reuse the clamp pieces. The tungsten secondary clamps were never tightened, and the outer pieces of piano wire secondary clamps were badly scarred but could be reused upside down.
- We successfully rehung the SR3 and RM. In the process we noticed and fixed an issue with the assembly frame (due to an out-of-date number in the Mirapro diagram, the IM crossbars were set 3 mm too high, which would have affected the wire length).
- We added the sections of the security structure below the RM and up to the BF.
- We installed the TM OSEM cables and routed them up to the IM.
- We installed the load gauge adapter and load gauge and prepared the IM/... section for weighing.
- We removed the three cracked F0 blades from the PI #3 in the SRM, and prepared for testing prototype new blades in that PI. We removed a floor panel under the PI and set up the filter service trolley underneath it with a stack of masses for a dummy load.
- Mirapro installed the SRM mushroom.
Plan for week of 5/14
- Mark, Enzo, Hirata-san, Kozu-kun at Kamioka Mon-Thu, then Osaka.
- Weigh IM/... section.
- Characterize F0 blade prototypes.
- Remove F0 blade prototypes (and send for rework if necessary).
- Start characterizing LBB blades.
- Crane in BF.
- Add IRM top plate, maraging rod, flying saucer.
- Suspend IM, check pitch, roll and vertical, adjust trim mass.
- Cable and (re-)test TM OSEMs, IM picos, BF yaw pico, BF LVDT and FR.
Plan for week of 5/21
- Mark, Enzo, Hirata-san, Kamioka Mon-Fri.
- Kozu-kun at Kamioka Wed-Fri.
- Install IRM sides, and IM OSEMs.
- Center IM OSEMs (in/out and laterally)
- Route all cables to underneath BF.
- Add BF internal ballast mass.
- Add BF cap.
Plan for week of 5/28
- Mark, Enzo, Hirata-san, Kamioka Mon-Fri.
- Kozu-kun at Kamioka Mon only.
- TBD.
To-Do Lists, Schedule