|
Size: 2208
Comment:
|
Size: 3282
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 6: | Line 6: |
| ==== Report for week of 4/9 ==== * Mark glued prisms and magnet/standoff assemblies on the SR3. The SR3 needed to be raised in the box by 0.7 mm to make the prisms go on at the right height, which was done using M4 washers under the PEEK feet. * Mark glued ferromagnetic disks on the last 5 IM flags. This completes 2 sets, for SR3 and SRM. * Mark configured two pico motor drivers ordered by Takahashi-san as SR3-IM and SRM-BF. * Enzo and Kozu-kun finished preparing and calibrating the SF and BF for SR3 and almost entirely finished with those for SRM. * Hirata-san worked on building two IMs for SR3 and SRM. The SR3 one just needs to have flags attached and to be weighed; the SRM needs another few hours work. * Shoda-san worked on the design of the metal SRM, on the LBB ballast mass, and on the plans for testing the BS in bKAGRA Phase 1. ==== Plan for week of 4/16 ==== * Shoda-san, Fujii-kun at Mitaka * Tanioka-san at Kamioka Tue-Thu * Others at Kamioka full week * -- * Move SF and BF for SRM out of the way. * Check results of gluing. * Build 1xRM * Calibrate OSEMs. * Start SR3 Hang * Reset assembly frame crossbars to correct heights. * Center the optical table. * Align the assembly frame vertically. * Install IM ring and IM. * Hang optic. * Hang RM. * Cable RM OSEMs. ==== Plan for week of 4/23 ==== * Shoda-san, Tanioka-san at Mitaka * Hirata-san at Mitaka * Mark, Enzo, Fujii-kun, Kozu-kun at Kamioka * -- * Clean parts (cable clamp bases, etc, etc). * Observe KAGRA Phase 1 operations, assist if problems arise. * Continue SR3 hang. ==== Plan for week of 4/30 ==== * Golden Week! |
==== Report for week of 11/19 ==== * SRM * We locked the suspension and craned it into the tank. This is the last Type B tank installation! * While inspecting the O-ring between the service ring and the lower section of the tank, Hirata-san found a small nick, so he replaced it. (This will hopefully be the last time that flange is closed, so it needs to be left ready for Mirapro to tighten.) * Hirata-san and Fabian removed the First Contact, but found that a tiny piece was left behind. With advice from Hirose-san, they managed to remove it via several rounds of dabbing with an acetone-soaked lens tissue. * They removed the IM-RM safety bar, unlocked the lower half of the suspension, and got it reasonably well aligned by eye. * They moved the vacuum feedthroughs and in-air cabling over, and reconnected nearly all the electronics. (The in-air cabling will need some tidying later, but * SR2 * Enzo and Mark set up the the SR2 OL. We may need to steal the LED back temporarily to do pitch setting on SRM, but we can take some interesting TFs on SR2 over the weekend. * SR3 * Enzo configured a new stepper driver for SR3_IP and returned the one that had been borrowed from SRM. (The original SR3_IP had been used to replace a water-damaged unit on the BS.) * Enzo worked on diagonalizing the IP and modeling of the whole suspension. He created Foton filters representing the response of the system in slots FM6-8 of the various filter banks. * Etc * Mark got three more MPCDs (M = "medium" or "modified") from AEL and moved coil drivers around until all Type B suspensions had a driver in every position, with MPCDs for IM-H and HPCDs everywhere else. He returned the unused LPCDs. * Mark did an inventory of all the Type B electronics and got the various JGW Doc electronic items lists up to date - see [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7276|E1707276]]. This included opening all the LVDT drivers to check that they had the original cards - BS, SR3 and SRM did, but SR2 had both input cards new. We let AEL know. * Hirata-san helped Furuta-san with floor repair. * Fabian changed the PR3 thermometer battery. * Mirapro installed a bellows on the -Y side of SR3. |
| Line 45: | Line 25: |
| * [[KAGRA/Subgroups/VIS/TypeB/March2018]] * [[KAGRA/Subgroups/VIS/TypeB/April2018]] |
|
| Line 49: | Line 27: |
| * [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7779|JGW-L1807779-v1 Type B Schedule (SR)]] | * [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7779|JGW-L1807779 Type B Schedule (SR)]] |
| Line 51: | Line 29: |
| ==== Vacation Info ==== * Fabian vacation, 3/26-4/27 (then gone). |
==== Plan for week of 12/17 ==== * Final alignment of SRM payload, plus BF and SF GAS. * (Time permitting) unlocking/centering/tuning of IP. * Installation of Enomoto-kun's beam target on SRM (if available). * Installation/testing of F0 steppers on SR2, SR3, SRM, and (hopefully) final vertical height adjustment. * Installation of viewports on SRM. ==== Plan for week of 12/24 ==== * Most of team on holidays - no Kamioka work. ==== Vacation/Etc Info ==== * Mark: 12/24 - 1/4. * Hirata-san: 12/24 - 1/4. * Fabian: TBD but similar. * Enzo: TBD but similar. * Mark and Enzo: KAGRA International Workshop in Perugia, 2/14-16. |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Report for week of 11/19
- SRM
- We locked the suspension and craned it into the tank. This is the last Type B tank installation!
- While inspecting the O-ring between the service ring and the lower section of the tank, Hirata-san found a small nick, so he replaced it. (This will hopefully be the last time that flange is closed, so it needs to be left ready for Mirapro to tighten.)
- Hirata-san and Fabian removed the First Contact, but found that a tiny piece was left behind. With advice from Hirose-san, they managed to remove it via several rounds of dabbing with an acetone-soaked lens tissue.
- They removed the IM-RM safety bar, unlocked the lower half of the suspension, and got it reasonably well aligned by eye.
- They moved the vacuum feedthroughs and in-air cabling over, and reconnected nearly all the electronics. (The in-air cabling will need some tidying later, but
- SR2
- Enzo and Mark set up the the SR2 OL. We may need to steal the LED back temporarily to do pitch setting on SRM, but we can take some interesting TFs on SR2 over the weekend.
- SR3
- Enzo configured a new stepper driver for SR3_IP and returned the one that had been borrowed from SRM. (The original SR3_IP had been used to replace a water-damaged unit on the BS.)
- Enzo worked on diagonalizing the IP and modeling of the whole suspension. He created Foton filters representing the response of the system in slots FM6-8 of the various filter banks.
- Etc
- Mark got three more MPCDs (M = "medium" or "modified") from AEL and moved coil drivers around until all Type B suspensions had a driver in every position, with MPCDs for IM-H and HPCDs everywhere else. He returned the unused LPCDs.
Mark did an inventory of all the Type B electronics and got the various JGW Doc electronic items lists up to date - see E1707276. This included opening all the LVDT drivers to check that they had the original cards - BS, SR3 and SRM did, but SR2 had both input cards new. We let AEL know.
- Hirata-san helped Furuta-san with floor repair.
- Fabian changed the PR3 thermometer battery.
- Mirapro installed a bellows on the -Y side of SR3.
To-Do Lists, Schedule
Plan for week of 12/17
- Final alignment of SRM payload, plus BF and SF GAS.
- (Time permitting) unlocking/centering/tuning of IP.
- Installation of Enomoto-kun's beam target on SRM (if available).
- Installation/testing of F0 steppers on SR2, SR3, SRM, and (hopefully) final vertical height adjustment.
- Installation of viewports on SRM.
Plan for week of 12/24
- Most of team on holidays - no Kamioka work.
Vacation/Etc Info
- Mark: 12/24 - 1/4.
- Hirata-san: 12/24 - 1/4.
- Fabian: TBD but similar.
- Enzo: TBD but similar.
- Mark and Enzo: KAGRA International Workshop in Perugia, 2/14-16.