Size: 2432
Comment:
|
Size: 3579
Comment:
|
Deletions are marked like this. | Additions are marked like this. |
Line 2: | Line 2: |
Line 6: | Line 5: |
==== Report for week of 7/9 ==== * We cleaned up after the heavy rain. There was no significant damage but some cardboard boxes of parts got wet and the contents needed to be moved to other containers and the boxes discarded. Water collected on the SR2 crane slot cover and had to be vacuumed away before the cover could be opened. A new section of corrugated roof was installed to minimize the problem for the future. * Enzo and team got all of the in-vacuum and in-air cables for the SF/... and PI properly routed and tested except (so far) for the geophones. * Hirata-san and team finished tuning of the F0 for SR2 and moved the PI into the SR2 cleanbooth. It turns out to be about 8 kg weaker than for SR3, whereas the SR2 chain is only 3 kg lighter, so we will have to do some combination of decompression, removing Cu segments and using a stronger CuBe spring (e.g., a Type A F0 FR blade instead of the F2 one in SR3). We closed the floor in the SRM area for safety, but we will probably reopen it as soon as next week for the SRM F0 build. * Hirata-san opened the SR3 tank, craned the LBB damper ring sandwich up to the top of the tank and suspended it. * Enzo and team corrected a lot of flipped connections on the SR3 PI LVDTs (primary<->secondary on the horizontal, primary<->actuation on the F0). * We added the arc weights and geophones and re-centered the IP. It seems stable and very soft, which is good. |
|
Line 14: | Line 6: |
==== Plan for week of 7/9 ==== ==== Plan for week of 7/16 ==== * Monday 7/16 is Sea Day. * Mark, Enzo, Hirata-san, Kozu-kun, Terrence at Kamioka Tue-Fri. ===== Main Sequence ===== * Check/restore alignment of payload, especially optic pitch. * Testing, TFs. * Lock suspension. * Crane into tank. * Unlock suspension. * Rearrange cables. * Test. |
=== Report for week of 2/12 (February 12th) === |
Line 27: | Line 8: |
===== F0/LBB Stuff ===== * Install correct IP in PI #2. * Crane PI #2 to second floor. * Rebuild top filter of PI #2. |
|
Line 32: | Line 9: |
==== To-Do Lists, Schedule ==== * [[KAGRA/Subgroups/VIS/TypeB/ToDoBS]] * [[KAGRA/Subgroups/VIS/TypeB/ToDoSR]] * [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7779|JGW-L1807779 Type B Schedule (SR)]] |
|
Line 37: | Line 10: |
==== Vacation Info ==== * Terrence: 8/24-26 f2f, then returns to Hong Kong. * Enzo: 9/14 JPS, 9/15 through 10/8 vacation in Chile. |
==== Report for week of 1/28 ==== * Etc * Mark inventoried lots of items and updated the [[KAGRA/Subgroups/VIS/TypeB/Status|Status]] page. * SR2 * Hirata-san helped with installing the obelisk on the LBB, and added counterweights to get the LBB level and at the right height for the first rough alignment. However the springs were still at or near the top stops, so he later pulled down the LBB with excess mass, locked the blades at the bottom of their range and reset the LBB rods and damping magnet ring, aiming off by 10 mm so that it would be correct when the LBB was allowed to rise to midrange on the blades. He left it pressed down for now so that Hirose-san could apply FC. Early next week he will release it and do the final ballasting. * Hirose-san applied and removed FC on both sides of the optic for cleanliness. * Mirapro hooked the LBB. * SR3 * Enzo installed IM damping filters. * Mark installed a BIO Converter for the stepper remote enable (which will eventually also be used for the WD). * Fabian researched buoyancy compensation and pre-applied as much as possible to SR3. The total compensation needed is 0.19 mm for F0, 0.48 mm for SF and 0.46 mm for BF, total 1.23 mm. 1.0 mm had been applied with the jacks. The initial plan was to apply the calculated amounts at each level but then offset F0 1.0 mm lower to undo the jack adjustment. However SF was stuck approximately 1 mm lower than it needed to end up, so the buoyancy correction for it will have to be done at F0, and F0 will end up quite close to nominal. * Fabian also offloaded the IM pico yaw adjustment done by Enomoto-kun-tachi to the F0 yaw stepper. This left the OSEMs well-centered, so we will not need to adjust them and the LBB can be released. * SRM * Enzo fixed the broken triple in-air pico adapter cable and we plugged it back in. * Fabian calibrated the F0 FR. * Enzo and Terrence installed the arc weights and geophones, tuned and centered the IP, and centered and calibrated the FRs. * Mirapro helped us with the camera viewport issue by giving us a gasket of the same type but a different brand from their stock, which snapped easily into place. We then installed the viewport on the tank. Kokeyama-san will help us add the camera and camera LAN cable next week. * Simon gave us all the remaining items for the SRM OL except the 3D stage for the LEN QPD. ==== Plan for week of 2/4 ==== * Mark, Enzo, Fabian, Terrence at Kamioka Mon-Fri. * Hirata-san at Kamioka Mon+TBD. * Etc * Split SR2, SR3 and SRM RT models. * Get rid of the power reel behind SRM and plug stuff into the new power point instead. * BS * Run BNC cables for stepper remote enable, plug into BIO, debug. * SR2 * Do buoyancy correction. * Install camera viewport. * Install camera. * Run BNC cables for stepper remote enable, plug into BIO, debug. * SR3 * Release LBB. * Ballast LBB. * Install camera viewport. * Install camera. * Debug stepper remote enable. * SRM * Install camera. * Ballast LBB. * Do buoyancy correction. * Set up OL. * Debug stepper remote enable. ==== Vacation/Travel Info ==== * Constitution Day, 2/11. * Mark and Enzo at KIW in Perugia, 2/12-18. * Enzo vacation, 3/5. * Enzo et al. Farewell Party, 3/7. * Enzo at JPS then final vacation, 3/13-29 * Terrence's last day, 3/29. |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Report for week of 2/12 (February 12th)
Report for week of 1/28
- Etc
Mark inventoried lots of items and updated the Status page.
- SR2
- Hirata-san helped with installing the obelisk on the LBB, and added counterweights to get the LBB level and at the right height for the first rough alignment. However the springs were still at or near the top stops, so he later pulled down the LBB with excess mass, locked the blades at the bottom of their range and reset the LBB rods and damping magnet ring, aiming off by 10 mm so that it would be correct when the LBB was allowed to rise to midrange on the blades. He left it pressed down for now so that Hirose-san could apply FC. Early next week he will release it and do the final ballasting.
- Hirose-san applied and removed FC on both sides of the optic for cleanliness.
- Mirapro hooked the LBB.
- SR3
- Enzo installed IM damping filters.
- Mark installed a BIO Converter for the stepper remote enable (which will eventually also be used for the WD).
- Fabian researched buoyancy compensation and pre-applied as much as possible to SR3. The total compensation needed is 0.19 mm for F0, 0.48 mm for SF and 0.46 mm for BF, total 1.23 mm. 1.0 mm had been applied with the jacks. The initial plan was to apply the calculated amounts at each level but then offset F0 1.0 mm lower to undo the jack adjustment. However SF was stuck approximately 1 mm lower than it needed to end up, so the buoyancy correction for it will have to be done at F0, and F0 will end up quite close to nominal.
- Fabian also offloaded the IM pico yaw adjustment done by Enomoto-kun-tachi to the F0 yaw stepper. This left the OSEMs well-centered, so we will not need to adjust them and the LBB can be released.
- SRM
- Enzo fixed the broken triple in-air pico adapter cable and we plugged it back in.
- Fabian calibrated the F0 FR.
- Enzo and Terrence installed the arc weights and geophones, tuned and centered the IP, and centered and calibrated the FRs.
- Mirapro helped us with the camera viewport issue by giving us a gasket of the same type but a different brand from their stock, which snapped easily into place. We then installed the viewport on the tank. Kokeyama-san will help us add the camera and camera LAN cable next week.
- Simon gave us all the remaining items for the SRM OL except the 3D stage for the LEN QPD.
Plan for week of 2/4
- Mark, Enzo, Fabian, Terrence at Kamioka Mon-Fri.
- Hirata-san at Kamioka Mon+TBD.
- Etc
- Split SR2, SR3 and SRM RT models.
- Get rid of the power reel behind SRM and plug stuff into the new power point instead.
- BS
- Run BNC cables for stepper remote enable, plug into BIO, debug.
- SR2
- Do buoyancy correction.
- Install camera viewport.
- Install camera.
- Run BNC cables for stepper remote enable, plug into BIO, debug.
- SR3
- Release LBB.
- Ballast LBB.
- Install camera viewport.
- Install camera.
- Debug stepper remote enable.
- SRM
- Install camera.
- Ballast LBB.
- Do buoyancy correction.
- Set up OL.
- Debug stepper remote enable.
Vacation/Travel Info
- Constitution Day, 2/11.
- Mark and Enzo at KIW in Perugia, 2/12-18.
- Enzo vacation, 3/5.
- Enzo et al. Farewell Party, 3/7.
- Enzo at JPS then final vacation, 3/13-29
- Terrence's last day, 3/29.