|
Size: 3552
Comment:
|
Size: 1802
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 2: | Line 2: |
| Line 6: | Line 5: |
| ==== Report for week of 7/30 ==== ===== SR3 ===== * We undid the accidental misalignment of the SR3. We also switched off the BF GAS offset we had been using, let the IM rise until near zero on the BF LVDT, and adjusted the IM vertical OSEMs back to mid-range. * We closed control loops for the SR3 GAS filters. * Terrence set up the LED and TILT QPD for the final OL, and did a new calibration. ===== SR2 ===== * We installed the SR2 SF damper magnet ring but found that the magnet pattern didn't match the Cu segments due to a different in the caps between SR3 and SR2. We raised the ring but left it suspended, clamped the template to the underside and rearranged the magnets. * We did a vertical height budget of the SR2. It turns out to have a very similar issue to the SR3: the chain is about 5 mm longer than the CAD, with about 3 mm of that between the SF and BF. We decided to do the same fix and operate with the F0 keystone 5 mm higher. We chose an total amount of ballast to give that keystone height and secured most of it to the SF, keeping a reserve for cables and the yaw stepper. * We routed most (all?) of the SF/... cabling up to the PI. |
==== Report for the week of 2/18 (February 18th) ==== |
| Line 16: | Line 7: |
| ===== SRM ===== * We moved the SRM assembly frame into its final position, reset it to the initial configuration, double-checked the heights of the crossbars, and lowered the optical table by 3 mm (to give margin for the optic to rise during hanging, which we had kept forgetting to do). We cleaned it up with the airgun and wet-wipes. We installed the IM ring and IM. * We assembled the SRM metal mass. Hirata-san made a jig from a plate with 4 screws which could safely hold the delicate front Sol-Black-coated ring upside down while the rest of the components were mounted on it. * We moved the metal mass to the mirror box and added the prisms and magnet standoffs. We applied the EP30 on Friday morning, but probably won't be able to check the result until after Obon. |
* On Friday and Saturday last week the pump down of the central area took place. We monitored the drift in the four Type B IPs. * During the week we recovered the four suspensions successfully: we recovered the alignment of IMs, GAS filters, IPs, oplevs and measured TFs. * Terrence, Enzo and Mark installed the length sensing components in SR2 oplev. It's working now and we should use it now to measure the optic's corresponding TF. * The SRM IM is still drifting but the speed is decreasing. Yesterday Thursday the speed was '''-81 nrad/min'''. With the aim of predicting when the drift may stop Terrece removed offsets from the time series segments and spliced them in order. The work is still on progress. * Terrence did more work in changing the real-time models. * Mark did some initial debugging on the stepper reset system, starting with SRM. However there seems to be some model-related problem. A BIO Checker Board gave sensible results for the low 32 bits of DIO card #0 (used for the TM LPCD) but nothing for the high 32 bits (used for steppers, and eventually also the WD). He added the stepper reset stuff to the circuit diagram (D1503660) and made other corrections. |
| Line 21: | Line 14: |
| ==== Plan for week of 8/13 ==== * KAGRA closed Mon, Tue. * Mark on vacation Mon-Thu, then Mitaka on Friday. * Enzo, Fabian, Terrence, Panwei, Rikako at Kamioka Wed-Fri. Probably no tunnel work. * Hirata-san on vacation all week. * TFs with new OL. * Controls work. * Tune SR3 IP? |
==== Plan for week of 2/25 ==== * Mark from Tuesday. * Enzo from Monday lunchtime. * Continue debugging stepper reset system. * Continue monitoring SRM yaw drift. * Install new RTMs and Guardian. * Work on Type B paper. |
| Line 30: | Line 22: |
| ==== Plan for week of 8/20 ==== * Mark, Enzo, Hirata-san, Fabian, Kozu-kun, Terrence, Panwei at Kamioka Mon-Fri. * Enzo, Hirata-san, Fabian, Kozu-kun, Terrence, Panwei at Kamioka Mon-Thu, then f2f. * Kozu-kun works at Mozumi Mon. ===== SR3 ===== * Hook LBB, add ballast mass. * Tune IP. ===== SR2 ===== * Adjust ballast/trim mass, with reserve for yaw stepper. * Cable/test PI items (LVDTs, steppers, geophones). * Set damper height. * Add arc weights, adjust IP. * Stage LBB damper rings in tank. ===== SRM ===== * Check gluing result - redo if necessary. * Assemble RM. * Add IM ballast masses (we forgot this before). * Get parts from AOL and set up new pitch-setting OL. * Hang metal mass. * Hang RM. ==== To-Do Lists, Schedule ==== * [[KAGRA/Subgroups/VIS/TypeB/ToDoBS]] * [[KAGRA/Subgroups/VIS/TypeB/ToDoSR]] * [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7779|JGW-L1807779 Type B Schedule (SR)]] ==== Vacation Info ==== * Mark: 8/13-16. * Hirata-san: 8/13-17 * Terrence: 8/24-26 f2f, then returns to Hong Kong. * Enzo: 9/14 JPS, 9/15 through 10/8 vacation in Chile. |
==== Vacation/Travel Info ==== * Enzo vacation, 3/5 and possibly 3/6. * Enzo et al. Farewell Party, 3/7. * Enzo at JPS then final vacation, 3/13-29 * Terrence's last day, 3/29. |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Report for the week of 2/18 (February 18th)
- On Friday and Saturday last week the pump down of the central area took place. We monitored the drift in the four Type B IPs.
- During the week we recovered the four suspensions successfully: we recovered the alignment of IMs, GAS filters, IPs, oplevs and measured TFs.
- Terrence, Enzo and Mark installed the length sensing components in SR2 oplev. It's working now and we should use it now to measure the optic's corresponding TF.
The SRM IM is still drifting but the speed is decreasing. Yesterday Thursday the speed was -81 nrad/min. With the aim of predicting when the drift may stop Terrece removed offsets from the time series segments and spliced them in order. The work is still on progress.
- Terrence did more work in changing the real-time models.
- Mark did some initial debugging on the stepper reset system, starting with SRM. However there seems to be some model-related problem. A BIO Checker Board gave sensible results for the low 32 bits of DIO card #0 (used for the TM LPCD) but nothing for the high 32 bits (used for steppers, and eventually also the WD). He added the stepper reset stuff to the circuit diagram (D1503660) and made other corrections.
Plan for week of 2/25
- Mark from Tuesday.
- Enzo from Monday lunchtime.
- Continue debugging stepper reset system.
- Continue monitoring SRM yaw drift.
- Install new RTMs and Guardian.
- Work on Type B paper.
Vacation/Travel Info
- Enzo vacation, 3/5 and possibly 3/6.
- Enzo et al. Farewell Party, 3/7.
- Enzo at JPS then final vacation, 3/13-29
- Terrence's last day, 3/29.