|
Size: 3657
Comment:
|
Size: 2738
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 2: | Line 2: |
| Line 6: | Line 5: |
| ==== Report for week of 7/30 ==== ===== SR3 ===== * We undid the accidental misalignment of the SR3. We also switched off the BF GAS offset we had been using, let the IM rise until near zero on the BF LVDT, and adjusted the IM vertical OSEMs back to mid-range. * We closed control loops for the SR3 GAS filters. * Terrence set up the LED and TILT QPD for the final OL, and did a new calibration. ===== SR2 ===== * We installed the SR2 SF damper magnet ring but found that the magnet pattern didn't match the Cu segments due to a different in the caps between SR3 and SR2. We raised the ring but left it suspended, clamped the template to the underside and rearranged the magnets. * We did a vertical height budget of the SR2. It turns out to have a very similar issue to the SR3: the chain is about 5 mm longer than the CAD, with about 3 mm of that between the SF and BF. We decided to do the same fix and operate with the F0 keystone 5 mm higher. We chose an total amount of ballast to give that keystone height and secured most of it to the SF, keeping a reserve for cables and the yaw stepper. * We routed most (all?) of the SF/... cabling up to the PI. |
==== Report for the week of 3/18 ==== * BS * Terrence notice that one of the IP LVDTs was not working. We traced it to an unplugged cable, plugged it back in and screwed it together to prevent a recurrence. * Simon helped us rebuild the damaged LEN OL QPD stage and Terrence reinstalled it. We removed a C-clamp that we had been using to immobilize the breadboard because it interfered with the QPD stage, and replaced it with a more elegant solution using a dog clamp underneath. * We noticed that the BS IP had fallen over in +L at some time shortly before Nakano-san aligned the optic on 3/18. Terrence tried to recenter it but it was unstable. We decided to remove the tank lid one more time and remove some arc weights. The IP frequency had been 39 mHz the last time it was measurable, and we increased it to a much-safer 80 mHz by removing 9 kg. We believe we were able to recover Nakano-san's alignment fairly closely. * Terrence then recalibrated and diagonalized both the TILT and LEN OL. * SR2 * Terrence recalibrated the OL. * SR3 * Mark pulled out unused cables leading into the SR3 cleanbooth. * SRM * Terrence set up the SRM Guardian. * Etc/All * Mark did an audit of the OL whitening/dewhitening system and fixed a bunch of problems: the SRM chassis was the wrong type, with no actual whitening card; SR2 and SRM needed whitening filters turned on; BS LEN needed the dewhitening turned on; SR2, SR3 and SRM needed dewhitening filters installed and turned on; SRM needed more gain. * Terrence weeded out a minor error from his OL diagonalization scheme and got L, T and Y independent at the 1% level for SR2 and SRM. He will do SR3 next. * Fabian measured the gain resistor values and other settings of the LVDT drivers, in case a card or chassis fails and we have to approximate the original state without the chance to recalibrate from scratch. * Fabian monitored the pumpdown. |
| Line 16: | Line 23: |
| ===== SRM ===== * We moved the SRM assembly frame into its final position, reset it to the initial configuration, double-checked the heights of the crossbars, and lowered the optical table by 3 mm (to give margin for the optic to rise during hanging, which we had kept forgetting to do). We cleaned it up with the airgun and wet-wipes. We installed the IM ring and IM. * We assembled the SRM metal mass. Hirata-san made a jig from a plate with 4 screws which could safely hold the delicate front Sol-Black-coated ring upside down while the rest of the components were mounted on it. * We moved the metal mass to the mirror box and added the prisms and magnet standoffs. We applied the EP30 on Friday morning, but probably won't be able to check the result until after Obon. |
==== Plan for week of 3/25 ==== * Mark, Fabian, Terrence at Kamioka Mon-Thu. * Assist with alignment. * Work on Type B paper. * Tidy up. * Throw out foil and other garbage. * Gather and clean tools. * Gather and organize unused parts and fasteners. * Return all unused cables to tent. * Tidy up cables in rear of SR2 rack. |
| Line 21: | Line 34: |
| ==== Plan for week of 8/13 ==== * KAGRA closed Mon, Tue. * Mark on vacation Mon-Thu, then Mitaka on Friday. * Enzo, Fabian, Terrence, Panwei, Rikako at Kamioka Wed-Fri. * Hirata-san on vacation all week. * Fujii-kun to help part-time with crane work and/or the IP tuning. * Diagonalization of new OL. * TFs with new OL. * Test of SF damper ring. * Controls work. * Tune SR3 IP. ==== Plan for week of 8/20 ==== * Mark, Enzo, Hirata-san, Fabian, Kozu-kun, Terrence, Panwei at Kamioka Mon-Fri. * Enzo, Hirata-san, Fabian, Kozu-kun, Terrence, Panwei at Kamioka Mon-Thu, then f2f. * Kozu-kun works at Mozumi Mon. ===== SR3 ===== * Hook LBB, add ballast mass. * Tune IP. ===== SR2 ===== * Adjust ballast/trim mass, with reserve for yaw stepper. * Cable/test PI items (LVDTs, steppers, geophones). * Set damper height. * Add arc weights, adjust IP. * Stage LBB damper rings in tank. ===== SRM ===== * Check gluing result - redo if necessary. * Assemble RM. * Add IM ballast masses (we forgot this before). * Get parts from AOL and set up new pitch-setting OL. * Hang metal mass. * Hang RM. ==== To-Do Lists, Schedule ==== * [[KAGRA/Subgroups/VIS/TypeB/ToDoBS]] * [[KAGRA/Subgroups/VIS/TypeB/ToDoSR]] * [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7779|JGW-L1807779 Type B Schedule (SR)]] ==== Vacation Info ==== * Mark: 8/13-16. * Hirata-san: 8/13-17 * Terrence: 8/24-26 f2f, then returns to Hong Kong. * Enzo: 9/14 JPS, 9/15 through 10/8 vacation in Chile. |
==== Vacation/Travel Info ==== * Enzo's final vacation till 3/29. * Terrence's last day for now, 3/29. * Mark compensation day for 3/21: 3/29. * Type B going-away party for Terrence/Enzo, 3/29 in Tokyo. * Terrence's next visit from 4/18. * Fabian's vacation 4/26 to 5/10. * Mark's final day ≈6/28 (TBD). |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Report for the week of 3/18
- BS
- Terrence notice that one of the IP LVDTs was not working. We traced it to an unplugged cable, plugged it back in and screwed it together to prevent a recurrence.
- Simon helped us rebuild the damaged LEN OL QPD stage and Terrence reinstalled it. We removed a C-clamp that we had been using to immobilize the breadboard because it interfered with the QPD stage, and replaced it with a more elegant solution using a dog clamp underneath.
- We noticed that the BS IP had fallen over in +L at some time shortly before Nakano-san aligned the optic on 3/18. Terrence tried to recenter it but it was unstable. We decided to remove the tank lid one more time and remove some arc weights. The IP frequency had been 39 mHz the last time it was measurable, and we increased it to a much-safer 80 mHz by removing 9 kg. We believe we were able to recover Nakano-san's alignment fairly closely.
- Terrence then recalibrated and diagonalized both the TILT and LEN OL.
- SR2
- Terrence recalibrated the OL.
- SR3
- Mark pulled out unused cables leading into the SR3 cleanbooth.
- SRM
- Terrence set up the SRM Guardian.
- Etc/All
- Mark did an audit of the OL whitening/dewhitening system and fixed a bunch of problems: the SRM chassis was the wrong type, with no actual whitening card; SR2 and SRM needed whitening filters turned on; BS LEN needed the dewhitening turned on; SR2, SR3 and SRM needed dewhitening filters installed and turned on; SRM needed more gain.
- Terrence weeded out a minor error from his OL diagonalization scheme and got L, T and Y independent at the 1% level for SR2 and SRM. He will do SR3 next.
- Fabian measured the gain resistor values and other settings of the LVDT drivers, in case a card or chassis fails and we have to approximate the original state without the chance to recalibrate from scratch.
- Fabian monitored the pumpdown.
Plan for week of 3/25
- Mark, Fabian, Terrence at Kamioka Mon-Thu.
- Assist with alignment.
- Work on Type B paper.
- Tidy up.
- Throw out foil and other garbage.
- Gather and clean tools.
- Gather and organize unused parts and fasteners.
- Return all unused cables to tent.
- Tidy up cables in rear of SR2 rack.
Vacation/Travel Info
- Enzo's final vacation till 3/29.
- Terrence's last day for now, 3/29.
- Mark compensation day for 3/21: 3/29.
- Type B going-away party for Terrence/Enzo, 3/29 in Tokyo.
- Terrence's next visit from 4/18.
- Fabian's vacation 4/26 to 5/10.
- Mark's final day ≈6/28 (TBD).