|
Size: 2272
Comment:
|
Size: 2069
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 5: | Line 5: |
| * Type B Past Week Summary * Mark and Fabian worked at Kamioka with Fujii-san: * We attempted to measure the tilt sensitivity of the accelerometers by adding shims under the legs but gave up when we discovered that picking up and putting down the accelerometer perturbs the zero point even without shims. We will probably need a special tilt stage to do this properly. * We took some frequency and Q measurements. The results were amplitude dependent. Joris thinks that this is due to not operating the accelerometers close enough to zero DC output. * We set up for a test of the geophone noise. One geophone is reading half the output of the others - one side of a differential signal has probably failed. * Type B ongoing issues * Wires * Need to decide RM wire thickness and order BS and RM wires. Lead time is a few days from Nilaco. * OSEMs * Akutsu-san is working to get wide-mouth OSEMs * Longer cables for BF->PI and SF->PI. * Takahashi-san has ordered extra connectors (due any day) and will get a company to make the cables. * Feedthrough Adapters * Need large quantity of male and female D-Sub 9, IDC ribbon connectors - Takahashi-san is getting a quote. * Can we make SR wire breakers bigger? * Fukushima-san will start on machining test soon (as of 5/27). * Installation stuff * "Ceiling" work in BS clean booth (removal of second floor section) scheduled for Fri 7/1. * Assembly frame construction scheduled for 7/4 * Ballast masses for payload * Initial batch received - ordered extra smaller ones to allow for adjustments. * Lower breadboard stuff * Installation to be incorporated into the procedure document. Mark/Takahashi to discuss. * Breadboard springs (in manufacture, expected end of July) * Nail-head parts: quote from Mirapro received, not urgent, will be combined with assembly frame order. * Documents * BS Assembly Procedure [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=4235| E1504235]], [[https://onedrive.live.com/redir?resid=D5CCFA70A378E0D0!195&authkey=!AM_usynuo9QI57g&ithint=folder,webloc|E1504235 draft]] |
=== Type B (Mark) === ==== Past week report ==== At Kamioka (Mark, Enzo, Yoshioka-kun): * We experimented with rearranging the arc weights to accommodate the magic wands and came up with a suitable scheme. * We used spare arc weights as extra ballast on the LBB to get it to float, and measured the height for a known load. * We put the blocks back under the LBB and unhooked it. * We moved the suspension from the tank back to the assembly frame. * We craned the LBB rings down onto the LBB but did not remove them yet. (This however is the last crane work in the tank until reinstallation, so the lid does not have to come off again and the pallet can be used for the PI.) * We put the crossbars back in the assembly frame underneath the SF and BF (and corrected an error in the height of the BF ones). * Enzo started setting up the SR3 rack (with help from Yamamoto-san). * We received the real BS optic and gluing tools, and glued the disks and rods into the modified magnet jigs. We also tried the re-made secondary prisms in the gluing jigs and made shims to hold them more securely. At Mitaka (Fabian and Hirata-san): * Hirata-san shipped the optic and gluing tools to Kamioka. * Hirata-san did drawings and RFQs for IM/BF/SF ballast masses * Fabian worked on the SRx assembly frame. ==== Plan for week of 7/18 ==== Full team at Kamioka from Tue-Fri, except Hirata-san (Tue-Wed only). * Glue prisms/magnets on BS. * Dismantle suspension. * Finish setting up filter service area (mostly already done by Mirapro). * Move BF to filter service area. ==== Plan for week of 7/24 ==== Full team at Kamioka from Mon-Fri, except Hirata-san (Tue-Fri) and Enzo (vacation). * Recheck alignment of assembly frame and centering of optical table. * Install IM, suspend BS and RM. Vacation Info: Hirata-san: Thu 7/20 through Mon 7/24 Enzo: Sat 7/22 through Sun 8/6 Fabian: Fri 8/4 through Mon 8/21 Mark: TBD Mid-Oct |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Past week report
At Kamioka (Mark, Enzo, Yoshioka-kun):
- We experimented with rearranging the arc weights to accommodate the magic wands and came up with a suitable scheme.
- We used spare arc weights as extra ballast on the LBB to get it to float, and measured the height for a known load.
- We put the blocks back under the LBB and unhooked it.
- We moved the suspension from the tank back to the assembly frame.
- We craned the LBB rings down onto the LBB but did not remove them yet. (This however is the last crane work in the tank until reinstallation, so the lid does not have to come off again and the pallet can be used for the PI.)
- We put the crossbars back in the assembly frame underneath the SF and BF (and corrected an error in the height of the BF ones).
- Enzo started setting up the SR3 rack (with help from Yamamoto-san).
- We received the real BS optic and gluing tools, and glued the disks and rods into the modified magnet jigs. We also tried the re-made secondary prisms in the gluing jigs and made shims to hold them more securely.
At Mitaka (Fabian and Hirata-san):
- Hirata-san shipped the optic and gluing tools to Kamioka.
- Hirata-san did drawings and RFQs for IM/BF/SF ballast masses
- Fabian worked on the SRx assembly frame.
Plan for week of 7/18
Full team at Kamioka from Tue-Fri, except Hirata-san (Tue-Wed only).
- Glue prisms/magnets on BS.
- Dismantle suspension.
- Finish setting up filter service area (mostly already done by Mirapro).
- Move BF to filter service area.
Plan for week of 7/24
Full team at Kamioka from Mon-Fri, except Hirata-san (Tue-Fri) and Enzo (vacation).
- Recheck alignment of assembly frame and centering of optical table.
- Install IM, suspend BS and RM.
Vacation Info: Hirata-san: Thu 7/20 through Mon 7/24 Enzo: Sat 7/22 through Sun 8/6 Fabian: Fri 8/4 through Mon 8/21 Mark: TBD Mid-Oct