Size: 2574
Comment:
|
Size: 46461
Comment:
|
Deletions are marked like this. | Additions are marked like this. |
Line 2: | Line 2: |
Line 5: | Line 4: |
* Type B Past Week Summary * Mark and Fabian worked at Kamioka with Fujii-san: * We attempted to measure the tilt sensitivity of the accelerometers by adding shims under the legs but gave up when we discovered that picking up and putting down the accelerometer perturbs the zero point even without shims. We will probably need a special tilt stage to do this properly. * We took some frequency and Q measurements. The results were amplitude dependent. Joris thinks that this is due to not operating the accelerometers close enough to zero DC output. * We set up for a test of the geophone noise. One geophone is reading half the output of the others - one side of a differential signal has probably failed. * Hirata-san: * Received extra compensation masses and washed them. * Received PI guides, assembled them and shipped them to Kamioka. * Removed adhesive from base of BS flags in preparation for regluing. * Did assembly drawings for cable clamps and other add-on parts for BF and SF. * Type B ongoing issues * Wires * Need to decide RM wire thickness and order BS and RM wires. Lead time is a few days from Nilaco. * OSEMs * Akutsu-san is working to get wide-mouth OSEMs * Longer cables for BF->PI and SF->PI. * Takahashi-san has ordered extra connectors (due any day) and will get a company to make the cables. * Feedthrough Adapters * Need large quantity of male and female D-Sub 9, IDC ribbon connectors - Takahashi-san is getting a quote. * Can we make SR wire breakers bigger? * Fukushima-san will start on machining test soon (as of 5/27). * Installation stuff * "Ceiling" work in BS clean booth (removal of second floor section) scheduled for Fri 7/1. * Assembly frame construction scheduled for 7/4 * Ballast masses for payload * Initial batch received - ordered extra smaller ones to allow for adjustments. * Lower breadboard stuff * Installation to be incorporated into the procedure document. Mark/Takahashi to discuss. * Breadboard springs (in manufacture, expected end of July) * Nail-head parts: quote from Mirapro received, not urgent, will be combined with assembly frame order. * Documents * BS Assembly Procedure [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=4235| E1504235]], [[https://onedrive.live.com/redir?resid=D5CCFA70A378E0D0!195&authkey=!AM_usynuo9QI57g&ithint=folder,webloc|E1504235 draft]] |
=== Type B === Report for the week 09-12-2019 * Shoda-san modified the real-time model to implement Terrence Method for ASC control strategy. See [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=12097|12097]]. * On Monday I tested a script for the oplev diagonalization procedure based on Terrence's work. After the test I realized it required corrections and I need to use the suspension again. The writing of the proceedure is ongoing. * On Tuesday I measured the space available at the +X side of the SR2 vacuum chamber. Using the original orientation of the assembly farme there would be 17 cm between the large outer frame and the assembly frame, whereas on the original assembly place there were about 34 cm. It wouldn't be possible to stand. See klog entry [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=12041|12041]]. Nevertheless, if we rotate the frame by 90 degrees it seems possible to have more space. See klog entry [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=12065|12065]]. * In the context of SRM bottom filter repairs, I checked whether the SR chambers have doors at the Bottom Filter level like the BS chamber has. They don't. All they have is 20 cm flanges for viewports at the +Y and -Y sides. This may be a problem if we aim to fix the bottom filter without taking the suspension out of the chamber. The plan we had thought was to try to access the bottom filter using the chamber door and try to insert the fibre optic camera throught the holes for locking the keystone. With the small aperture we can likely stick in one arm only. * I designed a rough version of the limit switch for IM picomotors. * Hirata-san uploaded to JGWDoc the design and mass budget of the ballast for the optical tables: [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=10370|BS]] and [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=10659|PR/SR]]. === Plan for next week === * Compile and install SR real-time models. * People have begun to modify or turn off filters which are supposed to be off in OBSEVATION state, maybe I should aim to design the bandpass filters and then implement the Guardian OBSERVATION state. ==== Vacation/Travel Info ==== * ~-~-Friday next week late in the afternoon we have the KAGRA ceremony. -~ === Type B === Report for the week 23-09-2019 * I modified the real-time model in order to accomodate bandpass fillters and new DAQ channels. See [[http://gwwiki.icrr.u-tokyo.ac.jp/JGWwiki/http://klog.icrr.u-tokyo.ac.jp/osl/?r=11788|11788]]. * For the most part I used the same scheme as Type A. * As agreed in the previous meeting I added a matrix ramp switch in order to transit from velocity damping to bandpass filters. * The medm screen was modified accordingly. * I realized yesterday I hadn't added a monitor for the output of the new filters banks in the EUL basis. It's been added to the real-time model, it compiles but still has to be installed. * Real-time models for SR suspensionsmust be compiled and installed. * Together with Terrence I modified vistools in order to generate functions to manipulate added filter banks. See [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=11788|11788]]. * The future of vistools looks quite gray (the code is complicated, not commented and we don't know how to manipulate matrix switches). Some will likely be in regular Guardian. * I began adding code for the OBSERVATION state in a draft file. * There was an agreement with Okutomi-san to change Type B medm screens for something more illustrative of the signal paths. * The temperature in the BS area has increased. It's been lately between 23.7 and 23.8 degrees. The actuation on the top filter used to be -23,000 counts and is now -13,500 counts. * Yamada-kun and Yokozawa-san measured transfer functions from BS to DARM and calculated the noise contribution. See [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=11676|11676]], [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=11724|11724]], [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=11707|11707]]. * The results are affected by an error in the calibration and are yet to be corrected. * The contributions of TM_DAMP_L and TM_DAMP_Y were considered to be high. These filters are supposed to be off in OBSERVATION state. See this [[http://klog.icrr.u-tokyo.ac.jp/osl/uploads/11748_20191125213530_bstodarmbeforeimyrolloff.png|plot]]. * These filters were rolled-off and the a new estimation was calculated. See this other [[http://klog.icrr.u-tokyo.ac.jp/osl/uploads/11748_20191125213851_bstodarmafterimyrolloff.png|plot]]. * The roll-off of TM_DAMP_Y was conservative. * Ushiba-san turned off BS TM-L DAMP filter for the FPMI state ([[http://klog.icrr.u-tokyo.ac.jp/osl/?r=11783|11783]]). It may have been affecting the sensitivity. * For the purposes of ASC the diagonalization of the TM actuation with respect to the oplev was removed by commissioners and replaced by their own coil balancing and drivealign diagonalization. I couldn't find a klog for this. === Plan for next week === * Compile and install SR real-time models. * People have begun to modify or turn off filters which are supposed to be off in OBSEVATION state, maybe I should aim to design the bandpass filters and then implement the Guardian OBSERVATION state. ==== Vacation/Travel Info ==== * ~-~-Friday next week late in the afternoon we have the KAGRA ceremony. -~ ==== Report for the week 23-09-2019 ==== * ~-Terrence modified the real-time model in order to accomodate hierarchical actuation from the interferometer sensing and control system (ISC). The modified model has not been installed. See klog entry [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=10692|10692]]. -~ * ~-In previous meetings it was reported there was a problem with the medm screen or real-time model in the components related to IP LVDT correction with the seismometer signal. In reality a trivial operation was still required. The apparent problem has been fixed now and we can proceed to implement the sensor correction in SR2 when we have the time. -~ ==== Plan for next week ==== * ~-If we have the time it would be good to implement the sensor correction at least in the BS and test it in bad weather conditions. -~ * ~-Commit the changes that Terrence made to the real-time model. -~ ==== Vacation/Travel Info ==== * ~-Friday next week late in the afternoon we have the KAGRA ceremony. -~ === Type B === ==== Report for the week 13-09-2019 ==== * ~-In previous weeks we identified injected noise into the SR3 IM from the oplev (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=10262|10262]]). On Monday I put notches at various frequencies where there were peaks (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=10423|10423]]). This procedure seems to work but it's tedious and we should do it in an as-needed depending on the impact of each peak in the interferometer signal. -~ * ~-Shoda-san and Terrence began been working in IM-L to IM-P and IM-Y filters (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=10505|10505]]). -~ * ~-In a previuos week I modified the SR2 real-time model in order to do LVDT correction with the seismometer signals. This week was mainly troubleshooting and preparation: * We found a couple of errors in the real-time model (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=10460|10460]], [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=10509|10509]]). -~ * ~-Miyo-kun added ati-aliasing filter at the output of the PEM real-time model before the Dolphin network. -~ * ~-An integrator is needed for the seismometer signal in order to get a displacement. However, the automatically generated medm screen points to a different filter bank (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=10510|10510]]). This hasn't been fixed yet. -~ * ~-Still, I measured transfer functions from seismometer on the ground to IP LVDT in FLOAT state, data which can be corrected (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=10510|10510]]). -~ * ~-In SR2 the cables connecting the BIO output from the coil drivers to the DIO card inside the I/O chassis were connected in a wrong way. I fixed them (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=10464|10464]] and [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=10508|10508]]). -~ === Type B === ==== Report for the week 02-09-2019 ==== * ~-Shoda-san implemented new low frequency filters for the IMs using the oplev signals (e.g. klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=10355|10355]]). -~ * ~-With PEM team on Monday 2nd of September we put accelerometers on the two SR3 oplev platforms and on the large frame (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=10262|10262]]): -~ * ~-Above 10 Hz the coherence of the oplev readings with the upper platform accelerometer is high in several regions. -~ * ~-It was possible to identify injected oplev noise into the suspension by looking at the coherence between one of the accelerometers and the IM, including large peaks between 16 and 18 Hz. -~ * ~-There's more information in the diaggui file which hasn't been analyzed. -~ * ~-On Tuesday we moved SR2 and SRM oplev tilt QPDs to sensible positions after the commissioning team re-aligned the interferometer (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=10291|10291]]). -~ * ~-I checked the OSEMs position and V2 is in an uncomfortable position: only 140 um from the end of linear range. -~ * ~-Although until now I checked the position using the calibration information the OSEM flag has been in a nearby position for since the end of May (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9028|9028]]). -~ * ~-Due to a problem with the BF keystone, the clerance in the other direction is 140 um. -~ * ~-We decided to keep the keystone in the current position because it hasn't created any problems so far. -~ * ~-Nakano-kun reported the BS was moving too much in yaw. I did some measurement and noticed the inertial damping was injecting noise below 100 mHz (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=10354|10354]]). At 50 mHz there's even a feature 2.4 times larger with inertial damping. We should just turn the inertial damping off. It also happens that according to klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9991|9991]], it is not working so effectively in reducing the integrated RMS. -~ * ~-Last week I modified the real-time model to enable IP LVDT correction and feedforward with seismometer signals on the ground. On Thursday I worked inthe MEDM screen modification. -~ * ~-Terrence updated Guardian after a report from Shoda-san concerning SR2: Guardian was not tripping when the GAS filter coil driver hardware watchdog tripped (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=10352|10352]]). However, after the modification we realized of an additionl problem: in a situation in which the TM coil driver should trip, the GAS filter coil driver trips instead. -~ ==== Plan for next week ==== * ~-Finish the MEDM screen modification, install the real-time model and begin setting the LVDT correction with the seismometer signal. -~ * ~-In order to minimize the injection of ground motion with the oplev, roll-off the oplev signal before it's used by any filter. * Use a cutoff frequency of about 8 or 9 Hz. -~ * ~-In order to assess the amount of oplev control noise, ask Yokozawa-san to leave the accelerometer at the oplev upper platform in order to measure its coherece of the IM degrees of freedom. -~ * ~-Roll-off the GAS DC control filters in order to reduce the control noise in the observation frequency band. -~ * ~-Do we need to extend the GAS DC control filters to the micro-seismic region? -~ ==== Report for the week 26-08-2019 (Written by Fabian) ==== * ~-Shoda-san improved the SR3 optic pitch filter (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=10152|10152]], [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=10217|10217)]]. -~ * ~-For the SR3 optic Enomoto-kun implemented an integrator filter with UGF above the micro-seismic (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=10014|10014]]). This filter used the oplve signal. -~ * ~-It works well, but it requires a set-point, which is currently set at the IM level (for IM DC control) not at the optic level. -~ * ~-A clear and clean implementation requires moving the set-point to the optic level and then take the error signal to the IM. -~ * ~-Nakano-kun modified the SR2 optic set-point to a place which is not so suitable for the oplev. We will move the QPD on Monday. -~ * ~-I modified the SR2 tower real-time model to allow for LVDT correction and feedforward with seismometer. * I had to modify the PEM real-time model to connect the seismometer channels to the Dolphin network. -~ * ~-Both models compile and I'm currently modifying the medm screen. -~ * ~-Performance report * There was a typhoon before the F2F meeting and this week we have had bad weather, in both cases there was an increase of the micro-sesmic activity. -~ * ~-During the typoon we saw a large peak at 150 mHz and this week we saw a peak a large peak at 60 mHz. -~ * ~-With bad weather Type B suspensions' optic motion (upper limit) were above the requirement in TM-L displacement and velocity: BS [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=10046|10046]], SR2 [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=10052|10052]], SR3 [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=10056|10056]], SRM [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=10067|10067]]. -~ * ~-Nevertheless, in days with good weather the suspensions behave mostly well in ALGNED and FLOAT states: BS [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9697|9697]], SR2 [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9703|9703]], SR3 [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9702|9702]], SRM [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9704|9704]]. -~ * ~-I also found the vertical ground motion induces motion in TM-Y and TM-P, but even with bad weather the motion remain below the requirement. -~ * ~-With this bad weather I was able to measure transfer functions from the ground to (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=10170|10170]]). -~ ==== Plan for the week 02-09-2019 ==== * ~-On Monday I will work with Yokozawa-san putting accelerometers on the SR3 oplev platforms. We will likely turn the fans off to do measurements. -~ * ~-We will move the SR2 tilt oplev QPD. -~ * ~-Real-time model: move the optic set-point to the optic level. -~ * ~-Update medm screens. -~ * ~-Shoda-san reported a coil-driver not working properly with the binary input/output. I need to check. -~ * ~-Test Shoda-san's fisnhing rod off-loading script with SRM sometime next week. -~ * ~-Terrence will be back on Wednesday. -~ === Type B === ==== Report for the week 15-08-2019 (Written by Fabian) ==== * ~-Shoda-san improved the SR3 optic yaw motion (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9949|9949]]). -~ * ~-Improvement in the frequency band from 1 Hz to 2.3 Hz was achieved by modifying the IM-Y filter. The problem was not enough phase margin. -~ * ~-There's still a peak at 1.3 Hz. -~ * ~-She also modified the IM SENSALIGN matrix (diagonalization according to resonance peaks?) -~ * ~-Transfer functions should be measured again. -~ * ~-The BS optic has a large peak at 150 mHz (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9991|9991]]). -~ ==== Plan for the week 19-08-2019 ==== * ~-Enomoto-kun requested to extend the oplev control loop down to where the micro-seismic peak is. (Fabian.) -~ * ~-Assemsment of the motion of the SR optics around the micro-seimic region. (Due today.) -~ === Type B === ==== Report for the week 05-08-2019 (Written by Fabian) ==== * ~-After Shoda-san's report (entry [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9797|9797]]) I checked the condition of the filters in FLOAT state. -~ * ~-After a few tests I realized the whitening chassis didn't have a whitening filter board. See entry [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9844|9844]]. -~ * ~-I replaced the chassis with an appropriate one. See entry [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9876|9876]]. -~ * ~-I checked the configuration of the hardware whitening filters by checking the 32 bit dip switch boards for each supension. See entry [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9823|9823]] and [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9876|9876]]. -~ * ~-The switch configuration is the same for SRM and SR2. -~ * ~-For BS and SR3 the configurations are different. -~ * ~-Additionally, the configuration of the two boards used for the BS oplev are different from each other. -~ * ~-This situation should be reviewed. -~ * ~-Type Bp and Type A don't seem to be using software anti-whitening filters for oplevs. I haven't checked their hardwate whitening filters' configuration though. -~ * ~-At the begining of the week I continued noise hunting in SR3. See entry [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9807|9807]]. The goal was to identify the limiting elements for the control system in ALIGNED state. See entries -~ * ~-The motion of the '''IP-L''' induces motion in '''TM-P''' and '''TM-L''' in the frequency band '''from 0.135 Hz to 0.4 Hz'''. This should be fixed at the IP. There's no inertial damping yet. -~ * ~-The motion of the '''IM-L''' induces motion in '''TM-P''' nd '''TM-L''' in the frequency band from '''0.3 Hz to 0.8 Hz'''. Likely, this should be fixed with IML2TMP and IML2TML control filters. -~ * ~-The motion of the '''IM-P''' induces motion in '''TM-P''' and '''TM-L''' in the frequency band from '''0.135 Hz to 1 Hz'''. The motion in the band from '''0.135 to 0.4 Hz is likely ground motion coming from the IP''', however, the motion from 0.4 Hz to 1 Hz should be fixed with IMP2TML and IMP2TMP control filters. -~ * ~-The motion in '''IM-Y''' induces motion '''TM-Y''' between '''1 Hz and 2.3 Hz'''. This should be fixed with IMY2TMY control filters. -~ * ~-I began measuring transfer functions (IM-L to TM-L) but I should finish the setting the software anti-whitening filter first. -~ ==== Plan for the week 15-08-2019 ==== * ~-Finish measuring transfer functions. -~ * ~-Begin the design of filters. -~ ==== Report for the week 7/29 (Written by Fabian) ==== * ~-I offloaded fishing rods in GAS filters and IPs in BS and SRM. -~ * ~-I implemented scripts for the automatic measurement of amplitude spectral densities (ASDs) of suspension sensors (usually used for residual motion estimation). -~ * ~-Highlights of recent ASD measurements can be found in entry [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9726|9726]]. The residual motion was measured in ALIGNED and FLOAT states. -~ * ~-In SRM and SR3 the motion in ALINED state was smaller than in FLOAT state, which is expected. See entries and respectively . -~ * ~-In SR2, the motion in '''pitch''' and '''yaw''' displacement is '''larger in ALIGNED state''', and the '''longitudinal velocity''' is the '''same in both states'''. -~ * ~-In BS, the '''longitudinal displacement''' is the '''same in both states'''. -~ * ~-Some features of the measured ASDs are the following: * In '''SRM, SR3 and SR2''' in '''pitch''' there is either a large bump (SRM and SR3) or excitation (SR2) between 0.3 Hz and 1 Hz. [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9756|9756]]. -~ * ~-In '''SRM pitch''' the control system seems to be introducing noise in two frequency bands, before and after the bump. See [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9756|9756]]. -~ * ~-In '''SR3 pitch''' the control loops seems to be introducing noise between 1 Hz and 2 Hz. See [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9755|9755]]. -~ * ~-In '''SR2 pitch''' the control loops seems to be introducing noise between 0.380 Hz and 2 Hz. See [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9752|9752]]. -~ * ~-In '''SR2 yaw''' the control loops seems to be introducing noise between 0.045 Hz and 0.230 Hz. See [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9752|9752]]. -~ * ~-In '''SR2 longitudinal speed''' the control system seems to excite a large peak at 0.705 Hz. See [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9752|9752]]. -~ ==== Plan for the week 8/5 ==== * ~-Check the BS amplitude spectral densities. -~ * ~-Check the longitudinal degree of freedom in SRs. -~ * ~-Aim to identify noise sources. -~ === Type B === ==== Report for the week 7/22 (Written by Fabian) ==== * ~-Shoda-san set the auto-measurement scripts and directories. She measured the transfer functions having the suspensions in FLOAT state. -~ * ~-SR3 IM H2 OSEM channel noise hunting (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9613|9613]] and [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9629|9629]]).The symptom was that the noise in SR3 IM H2 channel was 4.7 times larger than in similar channels. When the suspension was quiet H2 was not measuring any displacement but only noise. We did several measurements: -~ * ~-We removed the cable from the satellite box at the AA filter input and terminated the input: the noise was still there. -~ * ~-We terminated the ADC from the inside of the AA filter box: the noise was gone, suggesting the problem was the AA filter. -~ * ~-We replaced the AA filter and repeated the measurement with the input terminated: the noise was still there. -~ * ~-We disconnected all the cables from the input of the AA filter and terminated the offending channel: the noise was still there. -~ * ~-We also changed cables and tried connecting the AA filter to the SRM rack but the noise was still there. -~ * ~-The solution was to use other channels for all IM-H OSEMs. The real-time model was changed accordingly. -~ * ~-The SR3 LVDT driver broke down (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9659|9659]]). -~ * ~-We changed the AA filter power cable and when we turned the filter back on the whole rack turned off momentarily and came back on, with the exception of the LVDT driver. -~ * ~-We tried turning it on but it kept switching off by itself. Tomura-san suspects there's a grounding problem. -~ * ~-We decided to change the driver. -~ * ~-LDVT driver replacement and adjustment (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9658|9658]] and [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9025|9025]]). -~ * ~-For each channel there are three resisitors which require adjustment and determine an input gain, an output gain and a phase. -~ * ~-The phase was originally measured with an oscilloscope and the resistor was adjusted using also the oscilloscope. -~ * ~-The output gain resistor was set to the desired value using the multi-meter. -~ * ~-For the input gain we tried mesuring the signal amplitude with the oscilloscope (per Nikhef instructions) but we didn't see any obvios change when changing the resistence value. -~ * ~-Alternatively we measured the input resistence values in the old cards and set the new ones accordingly. -~ * ~-We did quick measurements of transfer functions and they looked alright. Measurements with better frequency resolution are needed. -~ ==== Plan for the week 7/29 ==== * ~-Noise assessment in SR3. * IM-Y integrated RMS displacement with control system on. Compare with klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9494|9494]]. -~ * ~-Terrence verbally reported LVDTs are particulrly noisy. -~ * ~-I would like to measure ASD for all sensors (in FLOAT state) and compare with other suspensions. -~ * ~-Miyakawa-san is interested to find the origin of the noise in one particular channel. -~ * ~-Check SRM BF position. The set point should be zero (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=8672|8672]]) but today I realized it was set to 100 um sometime. -~ * ~-Check if we need to offload coil-magnet actuation onto fishing rods. -~ * ~-Remove the software de-white (OSEMs) and antiWTN (oplevs) filters used in some or all suspensions. We don't have hardware whitening filters at the input. -~ * ~-Compile information about Guardian states and make it available to all. -~ ==== Vacation/Travel Info ==== * ~-Terrence left Kamioka. He will be back on September. -~ === Type B (Mark) === ==== Report for the week 7/15 (Written by Fabian) ==== * ~-SR3 IM H2 noise hunting. -~ * ~-SRM oplev condition: when the suspension is in ALIGNED state the oplev (pitch) is saturated and yaw within an inconvenient range (non-linear). See klog entry [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9562|9562]]. -~ * ~-Currently we don't have a good reference for the optic alignment and we cannot decide by how much we should move the QPD. This situation is not new and we tried to cope with it by using historical data of IM DC feedback signal in a good orientation for the DRMI. However, this strategy didn't work. -~ * ~-The consequence is that in ALIGNED state the pitch feedback DC signal drifts. -~ * ~-Kokeyama-san and Valera aligned the mirror, provided a reference and we were able to move the QPD. See entry [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9579|9579]]. -~ * ~-The big flange was moved to another place. -~ * ~-BS IM2TM transfer functions were measured in ALIGNED state with the control system on. See entry [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9571|9571]]. -~ * ~-HPCD modification. See entry [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9541|9541]] and comments. -~ ==== Plan for the week 7/22 ==== * ~-Go back to the tunnel on Monday to continue the investigation in SR3 IM H2 OSEM noise. -~ ==== Vacation/Travel Info ==== * ~-Terrence goes back to Hong Kong on 7/27 (sat), last day in Kamioka: 7/25 (Thurs). -~ === Type B (Mark) === ==== Report for the week 7/8 (Written by Fabian) ==== * ~-There was DAQ channel update on Wednesday. -~ * ~-After making a wind shield for SR3 oplev last week Terrence revisited the design of the IM to TM control filter with oplev and tried to reduce the residual motion peak at 1.4 Hz reported by Izumi-san. -~ * ~-Last week we moved all the SRs oplev QPDs because they were off by an unsuitable amount. After the interfrometer was aligned again we realized some QPDs will likely require to be adjusted again (optimal position would be within ±50 in normalized displacement units): SR2 tilt and SRM tilt require further adjustment. -~ * ~-During DRMI commissioning people realized the SR3 yaw motion was too large and was compromising the stability. * The yaw peak-to-peak motion was 6 µrad and involved IM/RM/TM resonat modes at ~0.147 Hz and ~0.172 Hz. -~ * ~-Terrence realized the amplitude decreased just by turning off the IM yaw control. He tried to damp IM-Y with the oplev but more time is required. -~ * ~-We realized the H2 IM OSEM is likely too noisy and excites resonant motion. We went to the mine, checked the LED current monitor but couldn't find anything obviously wrong using the oscilloscope. More investigation is needed. -~ * ~-Enomoto-kun pointed out that the IM2TM oplev DC control might be marginally stable. Terrence measure the IM-Y to TM-Y transfer function and designed the filter again allowing a suitable phase margin at 0.14 Hz. -~ * ~-In the satellite boxes the label '''"CURR Mon. for PD"''' should be '''"CURR Mon. for LED"'''. -~ * ~-SR3 and SRM oplev sled are decreasing their power (e.g. 50% in 150 days in SR3). The situation has been reported to Akutsu-san already. -~ * ~-Fabian came up with a preliminary plan to search for common mode motion in Type B systems (after talking with Miyo-kun, Terrence and Lucia.) -~ * ~-Report the status of the control system. -~ ==== Plan for the week 15/8 ==== * ~-Go back to the tunnel on Tuesday to continue the investigation in SR3 IM H2 OSEM noise. -~ * ~-Measure and provide IM-L to TM-P transfer functions to the commissioning team (Stefan's request this morning). -~ ==== Vacation/Travel Info ==== * ~-Terrence goes back to Hong Kong on 7/27 (sat), last day in Kamioka: 7/25 (Thurs). -~ === Type B (Mark) === ==== Report for the week 7/1 (Written by Fabian) ==== * ~-Fabian and Terrence went through the process of oplev diagonalization for the purposes of knowledge transfer and procedure documentation. * There were small corrections to the procedure. -~ * ~-Terrence wrote the oplev section of the Type B paper. -~ * ~-Fabian began writing a rough draft of the procedure. -~ * ~-With the agreement of the comissioning team we decided to move the position of all of oplev QPDs. When the optics were aligned they were away from linear range. * Although the badly affected channels were only three, we decided to adjust all of them. -~ * ~-The procedure is described in klog entry [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9411|9411]]. -~ * ~-In order to keep the aligmment information, we took note of the IM DC control signal necessary to achive the alignment and and off-loaded the actuation onto the TEST channels while the oplev was adjusted with the control system off. -~ * ~-In the case of SRM the oplev was to the point of saturation and was not rendering a usable feedabck signal when the optic was alledgely in aligned state. In this case we looked for the appropriate amount of feedback in stored data from a time in which the DRMI had been locked. -~ * ~-On Friday we went to the tunnel in order to put a better wind shield around SR3 oplev optics. The aim is to reduce the noise and then improve the performance of the control system. -~ * ~-We found large and heavy blank flanges leaning on the large SR3 and SRM frames. Removing them will likely disturb the position of the IPs, which would require readjustig the QPDs again. We would like the flanges to remain there for O3 if possible. Fabian will write a message to the vacuum group with our request. -~ === Plan for the week 7/8 === * ~-Terrence and Fabian will continue writing the oplev diagonalization procedure. -~ * ~-Fabian will install the rolled-off the DC control filters. -~ === Type B (Mark) === ==== Report for the week 6/24 (Written by Terrence and Fabian) ==== * ~-Type B watchdog/DACKILL is split for tower and payload. Now, tripping the payload watchdog will only trigger the payload DACKILL while tripping the tower watchdog will trigger both watchdogs and DACKILL. The MEDM screen is updated to accommodate the changes. The screen is also modified so the reset buttons for watchdogs and DACKILL are all available on the same screen. In the middle of this work, a bug is discovered in the ModerateWD.c where setting 0 to the ramp down time would cause the WD to loop in an endless ramp down cycle. -~ * ~-The Guardian is updated to recognize if the payload is tripped and decide which tripped state it should go to, "TRIPPED" or "PAYLOAD_TRIPPED". So, if both tower and payload controls are on while the payload watchdog tripped, the guardian will jump to the "PAYLOAD_TRIPPED" state and shutdown payload controls only. When the WD and DACKILL are reset, the "TRIPPED" state will dump you out to the safe state where all controls are disengaged, while the "PAYLOAD_TRIPPED" state will dump you out to the "ENGAGING_IM_DAMPING" state where the tower controls are still on. -~ * ~-VIS monitor is updated. It will monitor the raw sensor input and actuator output and check if they are within the operation range. The indicator will turn orange when it is 50% out of range and will turn red if it is 90% out of range. The indicator for actuators will turn blue if they are not in use. The limits of the operating range can be set in userapps/vis/k1/guardian/VIS_DICT.py. The range for OL_PIT and OL_YAW are default to be [-1,1], the lower limit of the OL_SUMs are default to be 1000 counts while those for the other are default to be [-32768,32768]. -~ * ~-'''If you know the range of certain sensors and actuators, you are strongly encouraged to tweak the thresholds in the file.''' Otherwise, the function of the monitor will be very limited. -~ * ~-Fabian checked again the GAS filter control noise: * My previous calculation considered damping filters and those injected too much noise in the observation frequency band. Rolling the filters off with (high order) Butterworth filters rendered the system unstable. -~ * ~-I then considered DC control filters only and I was able reduce the injectetd noise to acceptable levels while keeping the loop stable. As pointed out by Shoda-san, this was the strategy devised for the Type B prototype. -~ * ~-This has only been tested in software, not in the actual system. I aim to do implement it next week. -~ * ~-This strategy will work only if the resonant motion of the system is not excited after disabling the payload and GAS chain damping control. On the 23rd of May Terrence measured the residual motion with the control system (including IP) on and off. There was no subtantial difference between the two. I aim to take more measurements. -~ * ~-Terrence and Fabian are currently going through the oplev diagonalization procedure and will write down the procedure. -~ * ~-Hirata-san worked in the design of the baffles for the BS. -~ ==== Plan for the week 7/1 ==== * ~-Terrence and Fabian will continue writing the oplev diagonalization procedure. -~ * ~-Fabian will install the rolled-off the DC control filters. -~ ==== Vacation/Travel Info ==== * ~-Terrence goes back to Hong Kong on 7/27 (sat), last day in Kamioka: 7/25 (Thurs). -~ * ~-Mark's final day 6/28. -~ === Type B (Mark) === ==== Report for the week 6/17 ==== * ~-Izum-san pointed out the SR3 oplev control loop was not able to damp resonances at 1.4 Hz and 1.2 Hz (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9290|9290]]). Terrence checked (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9299|9299]]): -~ * ~-He found that the optic TFs were coupled to about 10%. I assume something changed because, as far as I understand (Fabian), the oplev had been succesfully diagonalized before to less than 1% coupling. -~ * ~-He moved the IP and compared IP LENGTH with OPLEV LENGTH noting the the oplev was reading only 70% of the IP displacement. -~ * ~-In this conditions he diagonalized the oplev but failed. There was still coupling. -~ * ~-He introduced a factor to have the OPLEV LENGTH measurement equal to IP LENGTH measurement. -~ * ~-He successfully diagoinalized the oplev. -~ * ~-He then proceeded to checked the filter but he was unable to reduce the residual motion. Noise is the suspect. Having appropriate wind shield is recommended. -~ * ~-Fabian worked in rolling-off the control filters of the GAS filters. * According to klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=8979|8979]] the GAS filter control noise has to decrease by 5 orders of magnitude in order to meet the requirement at 10 Hz. -~ * ~-A Butterworth filter of order 20 with a cut-off frequency of 5 Hz seems to reduce the noise but renders the system unstable. -~ * ~-More work is necessary. -~ * ~-Fabian joined Enomoto-kun's lecture on how to align the X Fabry Perot cavity with green light. -~ ==== Plan for the week 6/24 ==== * ~-Terrence will work on... -~ * ~-Fabian will continue working in the rolling-off of the filters of the GAS filters control loops. -~ ==== Vacation/Travel Info ==== * ~-Terrence goes back to Hong Kong on 7/27. -~ * ~-Mark's final day 6/28. -~ === Type B (Mark) === ==== Report for the week 6/10 ==== * ~-Supporting the commisioning team. -~ ===== BS ===== * ~-Type B inertial damping. This means geophone diagonalization, blending filter optimizing, etc. -~ * ~-Optimization gives an odd looking blending filter that blends at ~120 Hz, but works fine in IP L. [[https://klog.icrr.u-tokyo.ac.jp/osl/?r=9199|9199]] -~ * ~-During PRMI lock, BS residual motion was too high which misaligned the beam too much from time to time and making the lock unstable. -~ * ~-To fix this, I improved OL windshield so I can study the residual motion of the BS. Then I copied IP L blending filter to IP T and IP Y and cranked up the IP damping and TM damping gain. This suppressed the residual motion so the requirements are met. After this, the BS was not causing any problem to the lock anymore. [[https://klog.icrr.u-tokyo.ac.jp/osl/?r=9219|9219]][[https://klog.icrr.u-tokyo.ac.jp/osl/?r=9235|9235]] -~ === Type B (Mark) === ==== Report for the week 6/3 ==== ===== SRM Inertial Damping and Residual Motion Stuff ===== * ~-See Klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9064|9064]] -~ * ~-SRM IP L and T is blended at ~110 mHz (partially optimized by gradient descent, stopped after 10 iterations, then manually adjusted.) while IP Y is blended at 260 mHz (Lucia's old filter). The stability test was carried over the past weekend with inertial damping and all other stages on. The system seems stable. -~ * ~-To study to performance of the inertial damping, I improvised an OL windshield for SRM. -~ * ~-Another round of diagonalization was carried just because we have better sensitivity. -~ * ~-With IP LVDT damping and other controls on, the residual motion is as follows [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9086|9086]]: -~ ~-RMS Displacement: || ||Requirement ||Result || ||L ||0.4 µm ||0.1076 µm || ||P ||1 µrad ||0.0569 µrad || ||Y ||1 µrad ||0.0598 µrad || -~ ~-RMS Velocity: || ||Requirement ||Result || ||L ||0.5 µm ||0.1014 µm/s || ||P ||/ ||0.2165 µrad/s || ||Y ||/ ||0.1776 µrad/s || -~ * ~-I measured the residual motion with inertial damping, inertial damping without LVDT DC, normal damping without LVDT DC. Results are pretty similar. -~ * ~-I modified the optimization algorithm to allow fine learning. The cost plateaued after ~300 iterations and the blending frequency was at 78.6 mHz. I tried implementing this blending filter but the system went unstable. -~ ===== SR3 Inertial Damping ===== * ~-The calibration, diagonalization for IP geophones was done. -~ * ~-I measured and fit noise floor for LVDTs and geophones. -~ * ~-I found that the IP geophones have a much higher noise level than those from SRM. (1 order of magnitude higher, see [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9088|9088]]) -~ * ~-This explains why the optimization result of the blending filter converges much quicker than that of SRM, because the geophone noise level limits the blending frequency to be at ~ 130 mHz. -~ * ~-However, when the system went unstable when the blending filter was implemented. I should try a higher blending frequency or manually adjusting the blending filter to have a proper shape. -~ === Type B (Mark) === ==== Report for the week 5/27 (written by Fabian) ==== * ~-Shoda-san implemented the moderate watchdog: when tripping the amount of actuation will ramp down to zero smoothly. Klog entry [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9009|9009]]. -~ * ~-Terrence updated the BS guardian. -~ * ~-Terrence designed a VIS status monitor. The font might be too small for some people. -~ * ~-Terrence worked on SRM inertial damping. * There is coherence between the geophones and LVDTs at 0.1 Hz. -~ * ~-He designed a filter with a blending frequency of 0.110 Hz. -~ * ~-The system seems stable. -~ * ~-For SR2 Fabian calculated the sensor noise fed back into the system by the control loop: entry [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=8979|8979]]. -~ * ~-The GAS filters' contrbution is too high. -~ * ~-I asked Enzo and he didn't rolled off the filters at higher frequecies. -~ * ~-Filter modification was assigned to Fabian. -~ * ~-Fabian and Yokozawa-san measured the settings of the SR3 LVDT driver. Klog entry [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=9025|9025]]. -~ * ~-In the weekly comissioning meeting Fabian made the commitment of writing a list of the measurements we want to do with the DRMI for Type B characterization.I will write it by next week and send it around for comnents. -~ === Type B (Mark) === ==== Report for the week 5/20 (written by Fabian) ==== * ~-Terrence implemented a filter for the inertial damping. See entry [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=8905|8905]]. -~ * ~-The highlight of the week is Terrence's measurement of the residual motion of the SR2 optic: as measured by the oplev, it does fulfill the RMS displacement and velocity requirements for lock acquisition and, partially, for the observation mode also. See the report at klog entry [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=8949|8949]]. -~ * ~-The integrated RMS was calculated from 5 Hz to DC because there are some peaks between 8 Hz and 10 Hz and whose origin still has to be clarified. See the report at entries [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=8918|8918]] and [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=8933|8933]]. -~ * ~-After Akutsu-san's suggestion Terrence improved the air shield in two rounds, including a cylindrical cover around the viewport. This reduced the noise by about a factor of 10. -~ * ~-He realized setting up the shield may have slightly changed something in the oplev and carried out another round of diagonalization. -~ * ~-He realized the H3 coil was not working. We fixed it.A cable was disconnected. -~ * ~-The optic residual motion in L showed a large peaks close to 0.2 Hz, which is where the micro-seismic may become apparent. The peak was not seen in P or Y. The inertial damping system is likely not working in a suitable way. The blending frequency is 0.190 Hz which may not be low enough. -~ * ~-At the end measurement of the residual motion reported was carried out with inertial damping only in yaw. -~ * ~-Fabian, Terrence and Fujii-kun measured the settings of the SR2, BS LVDT drivers and one of SR2's. See klogs [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=8941|8941]] , [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=8951|8951]] and [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=8952|8952]]. -~ * ~-Fabian worked more on the calculation of the amount of sensor noise injected: * I imported Panwei's OSEM noise measurements and calculated the virtual sensor noise. -~ * ~-I imported Fujii-kun's measuement of the geophone noise and calculated the virtual sensor noise. -~ * ~-I imported the blending filter -~ * ~-I wrote lots of comments in Sekiguchi-kun's Matlab scripts. -~ * ~-I will write a klog soon with preliminar results. -~ * ~-Fabian submitted and abstract for the Autumn JPS meeting on September. -~ ==== Plan for the week 5/25 ==== * ~-Terrence will work in the optimization of the inertial damping. -~ * ~-Fabian will continue with the calculation and prepare a presentation for the conference in Brazil. -~ ==== Report for Golden Week ==== * ~-Mark monitored vent and pumpdown, and worked on vistools.py. -~ ==== Report for the week of 5/6 ==== * ~-Lucia and Terrence got the blending working for the IP LVDTs and geophones. -~ * ~-Terrence and Mark modified the models and MEDM screens to add a new IP block, IDAMP, for damping using the blended signal with inertial information, and a new DAMPMODE block for ramping smoothly between IDAMP and the old DAMP. -~ * ~-Mark worked on vistools.py, improving the support for cdsMuxMatrix blocks (e.g., OSEM2EUL) and adding support for cdsRampMuxMatrix blocks (e.g., the newly introduced DAMPMODE). He also created two sets of unit tests, unittest.py and unittest.sh, for the two modes of use (as a Python module in other Python programs, and as a command-line utility in bash). -~ ==== Report for week of 5/13 ==== * ~-Terrence measured Q's for nearly all modes on SR2 from TFs and then did some ring-down tests to get a better estimate of some high-Q modes. -~ * ~-Terrence and Mark looked at the velocity and angular velocity noise of the SR2 as reported by the LEN and TILT OLs. * The Y signal was fairly clean and the Y RMS angular velocity requirement was met. However the L signal was quite noisy, and was also contaminating the P signal due to the large cross terms in the diagonalization matrix. The RMS L from 5 Hz down with damping on was around 10 µm/s, which is 10 times the requirement. However little of this was due to pendulum resonances - most of the noise was featureless and broadband. In displacement units the noise was flat up to about 1 Hz and then smoothly rolled off to f^-2. The noise in the raw P and Y signals (not yet divided by the sum) was about 10 times the noise in the SUM. -~ * ~-We tried improving the noise with different whitening settings. Increasing the overall gain, increasing it at the QPD but reducing it at the whitening filter, and switching off the 1-10Hz boost whitening filter (and compensating software filter) had no effect. Blocking the beam reduced the noise by about 2 orders and brought the raw P and Y in line with the SUM, suggesting that the problem was before the QPD. Akutsu-san says the noise spectrum looks like it may be limited by air currents, and we probably need better wind shielding. -~ * ~-Mark swapped in an improved version of `vistools.py`, debugged a few small issues, and simplified the `TYPEB.py` Guardian. -~ * ~-Fabian embarked on a project to calculate the residual motion within KAGRA's observation band (beginning at 10 Hz) to make sure The Type B suspension fulfills the requirement, and calculate the speed of the optic to make sure we can acquire the lock. * He modified Takanori's Simulink/Matlab simulation in order to include the length sensing oplev and its control feedback path. -~ * ~-He imported Enzo's IM/GAS/IP-LVDT filters into the simulation. -~ * ~-He imported into the simulation the measured LVDT floor noise (sensitivities). -~ * ~-He calculated the IP-L, IP-T and IP-Y sensitivities. -~ ==== Plan for week of 5/20 ==== * ~-Mark at Mitaka Mon, Tue; US from Wed till 6/11. -~ * ~-Fabian * Import Panwei's OSEM sensitivity measurements and calculate the sensitivity of the virtual IM sensors. -~ * ~-Import geophones sensitivities and calculate the sensitivity of the corresponding virtual sensors. -~ * ~-Import Licia's and Terrence's inertial sensing filters. -~ * ~-Terrence * Try to reduce the OL noise and get better estimates of the RMS velocity with damping on. -~ ==== Vacation/Travel Info ==== * ~-Terrence's next visit from 4/18 to 7/27. -~ * ~-Mark's final day 6/28. -~ |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B
Report for the week 09-12-2019
Shoda-san modified the real-time model to implement Terrence Method for ASC control strategy. See 12097.
- On Monday I tested a script for the oplev diagonalization procedure based on Terrence's work. After the test I realized it required corrections and I need to use the suspension again. The writing of the proceedure is ongoing.
On Tuesday I measured the space available at the +X side of the SR2 vacuum chamber. Using the original orientation of the assembly farme there would be 17 cm between the large outer frame and the assembly frame, whereas on the original assembly place there were about 34 cm. It wouldn't be possible to stand. See klog entry 12041. Nevertheless, if we rotate the frame by 90 degrees it seems possible to have more space. See klog entry 12065.
- In the context of SRM bottom filter repairs, I checked whether the SR chambers have doors at the Bottom Filter level like the BS chamber has. They don't. All they have is 20 cm flanges for viewports at the +Y and -Y sides. This may be a problem if we aim to fix the bottom filter without taking the suspension out of the chamber. The plan we had thought was to try to access the bottom filter using the chamber door and try to insert the fibre optic camera throught the holes for locking the keystone. With the small aperture we can likely stick in one arm only.
- I designed a rough version of the limit switch for IM picomotors.
Hirata-san uploaded to JGWDoc the design and mass budget of the ballast for the optical tables: BS and PR/SR.
Plan for next week
- Compile and install SR real-time models.
- People have begun to modify or turn off filters which are supposed to be off in OBSEVATION state, maybe I should aim to design the bandpass filters and then implement the Guardian OBSERVATION state.
Vacation/Travel Info
~-Friday next week late in the afternoon we have the KAGRA ceremony.
Type B
Report for the week 23-09-2019
I modified the real-time model in order to accomodate bandpass fillters and new DAQ channels. See 11788.
- For the most part I used the same scheme as Type A.
- As agreed in the previous meeting I added a matrix ramp switch in order to transit from velocity damping to bandpass filters.
- The medm screen was modified accordingly.
- I realized yesterday I hadn't added a monitor for the output of the new filters banks in the EUL basis. It's been added to the real-time model, it compiles but still has to be installed.
- Real-time models for SR suspensionsmust be compiled and installed.
Together with Terrence I modified vistools in order to generate functions to manipulate added filter banks. See 11788.
- The future of vistools looks quite gray (the code is complicated, not commented and we don't know how to manipulate matrix switches). Some will likely be in regular Guardian.
- I began adding code for the OBSERVATION state in a draft file.
- There was an agreement with Okutomi-san to change Type B medm screens for something more illustrative of the signal paths.
- The temperature in the BS area has increased. It's been lately between 23.7 and 23.8 degrees. The actuation on the top filter used to be -23,000 counts and is now -13,500 counts.
Yamada-kun and Yokozawa-san measured transfer functions from BS to DARM and calculated the noise contribution. See 11676, 11724, 11707.
- The results are affected by an error in the calibration and are yet to be corrected.
The contributions of TM_DAMP_L and TM_DAMP_Y were considered to be high. These filters are supposed to be off in OBSERVATION state. See this plot.
These filters were rolled-off and the a new estimation was calculated. See this other plot.
- The roll-off of TM_DAMP_Y was conservative.
Ushiba-san turned off BS TM-L DAMP filter for the FPMI state (11783). It may have been affecting the sensitivity.
- For the purposes of ASC the diagonalization of the TM actuation with respect to the oplev was removed by commissioners and replaced by their own coil balancing and drivealign diagonalization. I couldn't find a klog for this.
Plan for next week
- Compile and install SR real-time models.
- People have begun to modify or turn off filters which are supposed to be off in OBSEVATION state, maybe I should aim to design the bandpass filters and then implement the Guardian OBSERVATION state.
Vacation/Travel Info
~-Friday next week late in the afternoon we have the KAGRA ceremony.
Report for the week 23-09-2019
Terrence modified the real-time model in order to accomodate hierarchical actuation from the interferometer sensing and control system (ISC). The modified model has not been installed. See klog entry 10692.
In previous meetings it was reported there was a problem with the medm screen or real-time model in the components related to IP LVDT correction with the seismometer signal. In reality a trivial operation was still required. The apparent problem has been fixed now and we can proceed to implement the sensor correction in SR2 when we have the time.
Plan for next week
If we have the time it would be good to implement the sensor correction at least in the BS and test it in bad weather conditions.
Commit the changes that Terrence made to the real-time model.
Vacation/Travel Info
Friday next week late in the afternoon we have the KAGRA ceremony.
Type B
Report for the week 13-09-2019
In previous weeks we identified injected noise into the SR3 IM from the oplev (klog 10262). On Monday I put notches at various frequencies where there were peaks (klog 10423). This procedure seems to work but it's tedious and we should do it in an as-needed depending on the impact of each peak in the interferometer signal.
Shoda-san and Terrence began been working in IM-L to IM-P and IM-Y filters (klog 10505).
In a previuos week I modified the SR2 real-time model in order to do LVDT correction with the seismometer signals. This week was mainly troubleshooting and preparation: * We found a couple of errors in the real-time model (klog 10460, 10509).
Miyo-kun added ati-aliasing filter at the output of the PEM real-time model before the Dolphin network.
An integrator is needed for the seismometer signal in order to get a displacement. However, the automatically generated medm screen points to a different filter bank (klog 10510). This hasn't been fixed yet.
Still, I measured transfer functions from seismometer on the ground to IP LVDT in FLOAT state, data which can be corrected (klog 10510).
In SR2 the cables connecting the BIO output from the coil drivers to the DIO card inside the I/O chassis were connected in a wrong way. I fixed them (klog 10464 and 10508).
Type B
Report for the week 02-09-2019
Shoda-san implemented new low frequency filters for the IMs using the oplev signals (e.g. klog 10355).
With PEM team on Monday 2nd of September we put accelerometers on the two SR3 oplev platforms and on the large frame (klog 10262):
Above 10 Hz the coherence of the oplev readings with the upper platform accelerometer is high in several regions.
It was possible to identify injected oplev noise into the suspension by looking at the coherence between one of the accelerometers and the IM, including large peaks between 16 and 18 Hz.
There's more information in the diaggui file which hasn't been analyzed.
On Tuesday we moved SR2 and SRM oplev tilt QPDs to sensible positions after the commissioning team re-aligned the interferometer (klog 10291).
I checked the OSEMs position and V2 is in an uncomfortable position: only 140 um from the end of linear range.
Although until now I checked the position using the calibration information the OSEM flag has been in a nearby position for since the end of May (klog 9028).
Due to a problem with the BF keystone, the clerance in the other direction is 140 um.
We decided to keep the keystone in the current position because it hasn't created any problems so far.
Nakano-kun reported the BS was moving too much in yaw. I did some measurement and noticed the inertial damping was injecting noise below 100 mHz (klog 10354). At 50 mHz there's even a feature 2.4 times larger with inertial damping. We should just turn the inertial damping off. It also happens that according to klog 9991, it is not working so effectively in reducing the integrated RMS.
Last week I modified the real-time model to enable IP LVDT correction and feedforward with seismometer signals on the ground. On Thursday I worked inthe MEDM screen modification.
Terrence updated Guardian after a report from Shoda-san concerning SR2: Guardian was not tripping when the GAS filter coil driver hardware watchdog tripped (klog 10352). However, after the modification we realized of an additionl problem: in a situation in which the TM coil driver should trip, the GAS filter coil driver trips instead.
Plan for next week
Finish the MEDM screen modification, install the real-time model and begin setting the LVDT correction with the seismometer signal.
In order to minimize the injection of ground motion with the oplev, roll-off the oplev signal before it's used by any filter. * Use a cutoff frequency of about 8 or 9 Hz.
In order to assess the amount of oplev control noise, ask Yokozawa-san to leave the accelerometer at the oplev upper platform in order to measure its coherece of the IM degrees of freedom.
Roll-off the GAS DC control filters in order to reduce the control noise in the observation frequency band.
Do we need to extend the GAS DC control filters to the micro-seismic region?
Report for the week 26-08-2019 (Written by Fabian)
Shoda-san improved the SR3 optic pitch filter (klog 10152, 10217).
For the SR3 optic Enomoto-kun implemented an integrator filter with UGF above the micro-seismic (klog 10014). This filter used the oplve signal.
It works well, but it requires a set-point, which is currently set at the IM level (for IM DC control) not at the optic level.
A clear and clean implementation requires moving the set-point to the optic level and then take the error signal to the IM.
Nakano-kun modified the SR2 optic set-point to a place which is not so suitable for the oplev. We will move the QPD on Monday.
I modified the SR2 tower real-time model to allow for LVDT correction and feedforward with seismometer. * I had to modify the PEM real-time model to connect the seismometer channels to the Dolphin network.
Both models compile and I'm currently modifying the medm screen.
Performance report * There was a typhoon before the F2F meeting and this week we have had bad weather, in both cases there was an increase of the micro-sesmic activity.
During the typoon we saw a large peak at 150 mHz and this week we saw a peak a large peak at 60 mHz.
With bad weather Type B suspensions' optic motion (upper limit) were above the requirement in TM-L displacement and velocity: BS 10046, SR2 10052, SR3 10056, SRM 10067.
Nevertheless, in days with good weather the suspensions behave mostly well in ALGNED and FLOAT states: BS 9697, SR2 9703, SR3 9702, SRM 9704.
I also found the vertical ground motion induces motion in TM-Y and TM-P, but even with bad weather the motion remain below the requirement.
With this bad weather I was able to measure transfer functions from the ground to (klog 10170).
Plan for the week 02-09-2019
On Monday I will work with Yokozawa-san putting accelerometers on the SR3 oplev platforms. We will likely turn the fans off to do measurements.
We will move the SR2 tilt oplev QPD.
Real-time model: move the optic set-point to the optic level.
Update medm screens.
Shoda-san reported a coil-driver not working properly with the binary input/output. I need to check.
Test Shoda-san's fisnhing rod off-loading script with SRM sometime next week.
Terrence will be back on Wednesday.
Type B
Report for the week 15-08-2019 (Written by Fabian)
Shoda-san improved the SR3 optic yaw motion (klog 9949).
Improvement in the frequency band from 1 Hz to 2.3 Hz was achieved by modifying the IM-Y filter. The problem was not enough phase margin.
There's still a peak at 1.3 Hz.
She also modified the IM SENSALIGN matrix (diagonalization according to resonance peaks?)
Transfer functions should be measured again.
The BS optic has a large peak at 150 mHz (klog 9991).
Plan for the week 19-08-2019
Enomoto-kun requested to extend the oplev control loop down to where the micro-seismic peak is. (Fabian.)
Assemsment of the motion of the SR optics around the micro-seimic region. (Due today.)
Type B
Report for the week 05-08-2019 (Written by Fabian)
After Shoda-san's report (entry 9797) I checked the condition of the filters in FLOAT state.
I checked the configuration of the hardware whitening filters by checking the 32 bit dip switch boards for each supension. See entry 9823 and 9876.
The switch configuration is the same for SRM and SR2.
For BS and SR3 the configurations are different.
Additionally, the configuration of the two boards used for the BS oplev are different from each other.
This situation should be reviewed.
Type Bp and Type A don't seem to be using software anti-whitening filters for oplevs. I haven't checked their hardwate whitening filters' configuration though.
At the begining of the week I continued noise hunting in SR3. See entry 9807. The goal was to identify the limiting elements for the control system in ALIGNED state. See entries
The motion of the IP-L induces motion in TM-P and TM-L in the frequency band from 0.135 Hz to 0.4 Hz. This should be fixed at the IP. There's no inertial damping yet.
The motion of the IM-L induces motion in TM-P nd TM-L in the frequency band from 0.3 Hz to 0.8 Hz. Likely, this should be fixed with IML2TMP and IML2TML control filters.
The motion of the IM-P induces motion in TM-P and TM-L in the frequency band from 0.135 Hz to 1 Hz. The motion in the band from 0.135 to 0.4 Hz is likely ground motion coming from the IP, however, the motion from 0.4 Hz to 1 Hz should be fixed with IMP2TML and IMP2TMP control filters.
The motion in IM-Y induces motion TM-Y between 1 Hz and 2.3 Hz. This should be fixed with IMY2TMY control filters.
I began measuring transfer functions (IM-L to TM-L) but I should finish the setting the software anti-whitening filter first.
Plan for the week 15-08-2019
Finish measuring transfer functions.
Begin the design of filters.
Report for the week 7/29 (Written by Fabian)
I offloaded fishing rods in GAS filters and IPs in BS and SRM.
I implemented scripts for the automatic measurement of amplitude spectral densities (ASDs) of suspension sensors (usually used for residual motion estimation).
Highlights of recent ASD measurements can be found in entry 9726. The residual motion was measured in ALIGNED and FLOAT states.
In SRM and SR3 the motion in ALINED state was smaller than in FLOAT state, which is expected. See entries and respectively .
In SR2, the motion in pitch and yaw displacement is larger in ALIGNED state, and the longitudinal velocity is the same in both states.
In BS, the longitudinal displacement is the same in both states.
Some features of the measured ASDs are the following: * In SRM, SR3 and SR2 in pitch there is either a large bump (SRM and SR3) or excitation (SR2) between 0.3 Hz and 1 Hz. 9756.
In SRM pitch the control system seems to be introducing noise in two frequency bands, before and after the bump. See 9756.
In SR3 pitch the control loops seems to be introducing noise between 1 Hz and 2 Hz. See 9755.
In SR2 pitch the control loops seems to be introducing noise between 0.380 Hz and 2 Hz. See 9752.
In SR2 yaw the control loops seems to be introducing noise between 0.045 Hz and 0.230 Hz. See 9752.
In SR2 longitudinal speed the control system seems to excite a large peak at 0.705 Hz. See 9752.
Plan for the week 8/5
Check the BS amplitude spectral densities.
Check the longitudinal degree of freedom in SRs.
Aim to identify noise sources.
Type B
Report for the week 7/22 (Written by Fabian)
Shoda-san set the auto-measurement scripts and directories. She measured the transfer functions having the suspensions in FLOAT state.
SR3 IM H2 OSEM channel noise hunting (klog 9613 and 9629).The symptom was that the noise in SR3 IM H2 channel was 4.7 times larger than in similar channels. When the suspension was quiet H2 was not measuring any displacement but only noise. We did several measurements:
We removed the cable from the satellite box at the AA filter input and terminated the input: the noise was still there.
We terminated the ADC from the inside of the AA filter box: the noise was gone, suggesting the problem was the AA filter.
We replaced the AA filter and repeated the measurement with the input terminated: the noise was still there.
We disconnected all the cables from the input of the AA filter and terminated the offending channel: the noise was still there.
We also changed cables and tried connecting the AA filter to the SRM rack but the noise was still there.
The solution was to use other channels for all IM-H OSEMs. The real-time model was changed accordingly.
The SR3 LVDT driver broke down (klog 9659).
We changed the AA filter power cable and when we turned the filter back on the whole rack turned off momentarily and came back on, with the exception of the LVDT driver.
We tried turning it on but it kept switching off by itself. Tomura-san suspects there's a grounding problem.
We decided to change the driver.
LDVT driver replacement and adjustment (klog 9658 and 9025).
For each channel there are three resisitors which require adjustment and determine an input gain, an output gain and a phase.
The phase was originally measured with an oscilloscope and the resistor was adjusted using also the oscilloscope.
The output gain resistor was set to the desired value using the multi-meter.
For the input gain we tried mesuring the signal amplitude with the oscilloscope (per Nikhef instructions) but we didn't see any obvios change when changing the resistence value.
Alternatively we measured the input resistence values in the old cards and set the new ones accordingly.
We did quick measurements of transfer functions and they looked alright. Measurements with better frequency resolution are needed.
Plan for the week 7/29
Noise assessment in SR3. * IM-Y integrated RMS displacement with control system on. Compare with klog 9494.
Terrence verbally reported LVDTs are particulrly noisy.
I would like to measure ASD for all sensors (in FLOAT state) and compare with other suspensions.
Miyakawa-san is interested to find the origin of the noise in one particular channel.
Check SRM BF position. The set point should be zero (klog 8672) but today I realized it was set to 100 um sometime.
Check if we need to offload coil-magnet actuation onto fishing rods.
Remove the software de-white (OSEMs) and antiWTN (oplevs) filters used in some or all suspensions. We don't have hardware whitening filters at the input.
Compile information about Guardian states and make it available to all.
Vacation/Travel Info
Terrence left Kamioka. He will be back on September.
Type B (Mark)
Report for the week 7/15 (Written by Fabian)
SR3 IM H2 noise hunting.
SRM oplev condition: when the suspension is in ALIGNED state the oplev (pitch) is saturated and yaw within an inconvenient range (non-linear). See klog entry 9562.
Currently we don't have a good reference for the optic alignment and we cannot decide by how much we should move the QPD. This situation is not new and we tried to cope with it by using historical data of IM DC feedback signal in a good orientation for the DRMI. However, this strategy didn't work.
The consequence is that in ALIGNED state the pitch feedback DC signal drifts.
Kokeyama-san and Valera aligned the mirror, provided a reference and we were able to move the QPD. See entry 9579.
The big flange was moved to another place.
BS IM2TM transfer functions were measured in ALIGNED state with the control system on. See entry 9571.
HPCD modification. See entry 9541 and comments.
Plan for the week 7/22
Go back to the tunnel on Monday to continue the investigation in SR3 IM H2 OSEM noise.
Vacation/Travel Info
Terrence goes back to Hong Kong on 7/27 (sat), last day in Kamioka: 7/25 (Thurs).
Type B (Mark)
Report for the week 7/8 (Written by Fabian)
There was DAQ channel update on Wednesday.
After making a wind shield for SR3 oplev last week Terrence revisited the design of the IM to TM control filter with oplev and tried to reduce the residual motion peak at 1.4 Hz reported by Izumi-san.
Last week we moved all the SRs oplev QPDs because they were off by an unsuitable amount. After the interfrometer was aligned again we realized some QPDs will likely require to be adjusted again (optimal position would be within ±50 in normalized displacement units): SR2 tilt and SRM tilt require further adjustment.
During DRMI commissioning people realized the SR3 yaw motion was too large and was compromising the stability. * The yaw peak-to-peak motion was 6 µrad and involved IM/RM/TM resonat modes at ~0.147 Hz and ~0.172 Hz.
Terrence realized the amplitude decreased just by turning off the IM yaw control. He tried to damp IM-Y with the oplev but more time is required.
We realized the H2 IM OSEM is likely too noisy and excites resonant motion. We went to the mine, checked the LED current monitor but couldn't find anything obviously wrong using the oscilloscope. More investigation is needed.
Enomoto-kun pointed out that the IM2TM oplev DC control might be marginally stable. Terrence measure the IM-Y to TM-Y transfer function and designed the filter again allowing a suitable phase margin at 0.14 Hz.
In the satellite boxes the label "CURR Mon. for PD" should be "CURR Mon. for LED".
SR3 and SRM oplev sled are decreasing their power (e.g. 50% in 150 days in SR3). The situation has been reported to Akutsu-san already.
Fabian came up with a preliminary plan to search for common mode motion in Type B systems (after talking with Miyo-kun, Terrence and Lucia.)
Report the status of the control system.
Plan for the week 15/8
Go back to the tunnel on Tuesday to continue the investigation in SR3 IM H2 OSEM noise.
Measure and provide IM-L to TM-P transfer functions to the commissioning team (Stefan's request this morning).
Vacation/Travel Info
Terrence goes back to Hong Kong on 7/27 (sat), last day in Kamioka: 7/25 (Thurs).
Type B (Mark)
Report for the week 7/1 (Written by Fabian)
Fabian and Terrence went through the process of oplev diagonalization for the purposes of knowledge transfer and procedure documentation. * There were small corrections to the procedure.
Terrence wrote the oplev section of the Type B paper.
Fabian began writing a rough draft of the procedure.
With the agreement of the comissioning team we decided to move the position of all of oplev QPDs. When the optics were aligned they were away from linear range. * Although the badly affected channels were only three, we decided to adjust all of them.
The procedure is described in klog entry 9411.
In order to keep the aligmment information, we took note of the IM DC control signal necessary to achive the alignment and and off-loaded the actuation onto the TEST channels while the oplev was adjusted with the control system off.
In the case of SRM the oplev was to the point of saturation and was not rendering a usable feedabck signal when the optic was alledgely in aligned state. In this case we looked for the appropriate amount of feedback in stored data from a time in which the DRMI had been locked.
On Friday we went to the tunnel in order to put a better wind shield around SR3 oplev optics. The aim is to reduce the noise and then improve the performance of the control system.
We found large and heavy blank flanges leaning on the large SR3 and SRM frames. Removing them will likely disturb the position of the IPs, which would require readjustig the QPDs again. We would like the flanges to remain there for O3 if possible. Fabian will write a message to the vacuum group with our request.
Plan for the week 7/8
Terrence and Fabian will continue writing the oplev diagonalization procedure.
Fabian will install the rolled-off the DC control filters.
Type B (Mark)
Report for the week 6/24 (Written by Terrence and Fabian)
Type B watchdog/DACKILL is split for tower and payload. Now, tripping the payload watchdog will only trigger the payload DACKILL while tripping the tower watchdog will trigger both watchdogs and DACKILL. The MEDM screen is updated to accommodate the changes. The screen is also modified so the reset buttons for watchdogs and DACKILL are all available on the same screen. In the middle of this work, a bug is discovered in the ModerateWD.c where setting 0 to the ramp down time would cause the WD to loop in an endless ramp down cycle.
The Guardian is updated to recognize if the payload is tripped and decide which tripped state it should go to, "TRIPPED" or "PAYLOAD_TRIPPED". So, if both tower and payload controls are on while the payload watchdog tripped, the guardian will jump to the "PAYLOAD_TRIPPED" state and shutdown payload controls only. When the WD and DACKILL are reset, the "TRIPPED" state will dump you out to the safe state where all controls are disengaged, while the "PAYLOAD_TRIPPED" state will dump you out to the "ENGAGING_IM_DAMPING" state where the tower controls are still on.
VIS monitor is updated. It will monitor the raw sensor input and actuator output and check if they are within the operation range. The indicator will turn orange when it is 50% out of range and will turn red if it is 90% out of range. The indicator for actuators will turn blue if they are not in use. The limits of the operating range can be set in userapps/vis/k1/guardian/VIS_DICT.py. The range for OL_PIT and OL_YAW are default to be [-1,1], the lower limit of the OL_SUMs are default to be 1000 counts while those for the other are default to be [-32768,32768].
If you know the range of certain sensors and actuators, you are strongly encouraged to tweak the thresholds in the file. Otherwise, the function of the monitor will be very limited.
Fabian checked again the GAS filter control noise: * My previous calculation considered damping filters and those injected too much noise in the observation frequency band. Rolling the filters off with (high order) Butterworth filters rendered the system unstable.
I then considered DC control filters only and I was able reduce the injectetd noise to acceptable levels while keeping the loop stable. As pointed out by Shoda-san, this was the strategy devised for the Type B prototype.
This has only been tested in software, not in the actual system. I aim to do implement it next week.
This strategy will work only if the resonant motion of the system is not excited after disabling the payload and GAS chain damping control. On the 23rd of May Terrence measured the residual motion with the control system (including IP) on and off. There was no subtantial difference between the two. I aim to take more measurements.
Terrence and Fabian are currently going through the oplev diagonalization procedure and will write down the procedure.
Hirata-san worked in the design of the baffles for the BS.
Plan for the week 7/1
Terrence and Fabian will continue writing the oplev diagonalization procedure.
Fabian will install the rolled-off the DC control filters.
Vacation/Travel Info
Terrence goes back to Hong Kong on 7/27 (sat), last day in Kamioka: 7/25 (Thurs).
Mark's final day 6/28.
Type B (Mark)
Report for the week 6/17
Izum-san pointed out the SR3 oplev control loop was not able to damp resonances at 1.4 Hz and 1.2 Hz (klog 9290). Terrence checked (klog 9299):
He found that the optic TFs were coupled to about 10%. I assume something changed because, as far as I understand (Fabian), the oplev had been succesfully diagonalized before to less than 1% coupling.
He moved the IP and compared IP LENGTH with OPLEV LENGTH noting the the oplev was reading only 70% of the IP displacement.
In this conditions he diagonalized the oplev but failed. There was still coupling.
He introduced a factor to have the OPLEV LENGTH measurement equal to IP LENGTH measurement.
He successfully diagoinalized the oplev.
He then proceeded to checked the filter but he was unable to reduce the residual motion. Noise is the suspect. Having appropriate wind shield is recommended.
Fabian worked in rolling-off the control filters of the GAS filters. * According to klog 8979 the GAS filter control noise has to decrease by 5 orders of magnitude in order to meet the requirement at 10 Hz.
A Butterworth filter of order 20 with a cut-off frequency of 5 Hz seems to reduce the noise but renders the system unstable.
More work is necessary.
Fabian joined Enomoto-kun's lecture on how to align the X Fabry Perot cavity with green light.
Plan for the week 6/24
Terrence will work on...
Fabian will continue working in the rolling-off of the filters of the GAS filters control loops.
Vacation/Travel Info
Terrence goes back to Hong Kong on 7/27.
Mark's final day 6/28.
Type B (Mark)
Report for the week 6/10
Supporting the commisioning team.
BS
Type B inertial damping. This means geophone diagonalization, blending filter optimizing, etc.
Optimization gives an odd looking blending filter that blends at ~120 Hz, but works fine in IP L. 9199
During PRMI lock, BS residual motion was too high which misaligned the beam too much from time to time and making the lock unstable.
To fix this, I improved OL windshield so I can study the residual motion of the BS. Then I copied IP L blending filter to IP T and IP Y and cranked up the IP damping and TM damping gain. This suppressed the residual motion so the requirements are met. After this, the BS was not causing any problem to the lock anymore. 92199235
Type B (Mark)
Report for the week 6/3
SRM Inertial Damping and Residual Motion Stuff
See Klog 9064
SRM IP L and T is blended at ~110 mHz (partially optimized by gradient descent, stopped after 10 iterations, then manually adjusted.) while IP Y is blended at 260 mHz (Lucia's old filter). The stability test was carried over the past weekend with inertial damping and all other stages on. The system seems stable.
To study to performance of the inertial damping, I improvised an OL windshield for SRM.
Another round of diagonalization was carried just because we have better sensitivity.
With IP LVDT damping and other controls on, the residual motion is as follows 9086:
RMS Displacement: Requirement Result L 0.4 µm 0.1076 µm P 1 µrad 0.0569 µrad Y 1 µrad 0.0598 µrad
RMS Velocity: Requirement Result L 0.5 µm 0.1014 µm/s P / 0.2165 µrad/s Y / 0.1776 µrad/s
I measured the residual motion with inertial damping, inertial damping without LVDT DC, normal damping without LVDT DC. Results are pretty similar.
I modified the optimization algorithm to allow fine learning. The cost plateaued after ~300 iterations and the blending frequency was at 78.6 mHz. I tried implementing this blending filter but the system went unstable.
SR3 Inertial Damping
The calibration, diagonalization for IP geophones was done.
I measured and fit noise floor for LVDTs and geophones.
I found that the IP geophones have a much higher noise level than those from SRM. (1 order of magnitude higher, see 9088)
This explains why the optimization result of the blending filter converges much quicker than that of SRM, because the geophone noise level limits the blending frequency to be at ~ 130 mHz.
However, when the system went unstable when the blending filter was implemented. I should try a higher blending frequency or manually adjusting the blending filter to have a proper shape.
Type B (Mark)
Report for the week 5/27 (written by Fabian)
Shoda-san implemented the moderate watchdog: when tripping the amount of actuation will ramp down to zero smoothly. Klog entry 9009.
Terrence updated the BS guardian.
Terrence designed a VIS status monitor. The font might be too small for some people.
Terrence worked on SRM inertial damping. * There is coherence between the geophones and LVDTs at 0.1 Hz.
He designed a filter with a blending frequency of 0.110 Hz.
The system seems stable.
For SR2 Fabian calculated the sensor noise fed back into the system by the control loop: entry 8979.
The GAS filters' contrbution is too high.
I asked Enzo and he didn't rolled off the filters at higher frequecies.
Filter modification was assigned to Fabian.
Fabian and Yokozawa-san measured the settings of the SR3 LVDT driver. Klog entry 9025.
In the weekly comissioning meeting Fabian made the commitment of writing a list of the measurements we want to do with the DRMI for Type B characterization.I will write it by next week and send it around for comnents.
Type B (Mark)
Report for the week 5/20 (written by Fabian)
Terrence implemented a filter for the inertial damping. See entry 8905.
The highlight of the week is Terrence's measurement of the residual motion of the SR2 optic: as measured by the oplev, it does fulfill the RMS displacement and velocity requirements for lock acquisition and, partially, for the observation mode also. See the report at klog entry 8949.
The integrated RMS was calculated from 5 Hz to DC because there are some peaks between 8 Hz and 10 Hz and whose origin still has to be clarified. See the report at entries 8918 and 8933.
After Akutsu-san's suggestion Terrence improved the air shield in two rounds, including a cylindrical cover around the viewport. This reduced the noise by about a factor of 10.
He realized setting up the shield may have slightly changed something in the oplev and carried out another round of diagonalization.
He realized the H3 coil was not working. We fixed it.A cable was disconnected.
The optic residual motion in L showed a large peaks close to 0.2 Hz, which is where the micro-seismic may become apparent. The peak was not seen in P or Y. The inertial damping system is likely not working in a suitable way. The blending frequency is 0.190 Hz which may not be low enough.
At the end measurement of the residual motion reported was carried out with inertial damping only in yaw.
Fabian, Terrence and Fujii-kun measured the settings of the SR2, BS LVDT drivers and one of SR2's. See klogs 8941 , 8951 and 8952.
Fabian worked more on the calculation of the amount of sensor noise injected: * I imported Panwei's OSEM noise measurements and calculated the virtual sensor noise.
I imported Fujii-kun's measuement of the geophone noise and calculated the virtual sensor noise.
I imported the blending filter
I wrote lots of comments in Sekiguchi-kun's Matlab scripts.
I will write a klog soon with preliminar results.
Fabian submitted and abstract for the Autumn JPS meeting on September.
Plan for the week 5/25
Terrence will work in the optimization of the inertial damping.
Fabian will continue with the calculation and prepare a presentation for the conference in Brazil.
Report for Golden Week
Mark monitored vent and pumpdown, and worked on vistools.py.
Report for the week of 5/6
Lucia and Terrence got the blending working for the IP LVDTs and geophones.
Terrence and Mark modified the models and MEDM screens to add a new IP block, IDAMP, for damping using the blended signal with inertial information, and a new DAMPMODE block for ramping smoothly between IDAMP and the old DAMP.
Mark worked on vistools.py, improving the support for cdsMuxMatrix blocks (e.g., OSEM2EUL) and adding support for cdsRampMuxMatrix blocks (e.g., the newly introduced DAMPMODE). He also created two sets of unit tests, unittest.py and unittest.sh, for the two modes of use (as a Python module in other Python programs, and as a command-line utility in bash).
Report for week of 5/13
Terrence measured Q's for nearly all modes on SR2 from TFs and then did some ring-down tests to get a better estimate of some high-Q modes.
Terrence and Mark looked at the velocity and angular velocity noise of the SR2 as reported by the LEN and TILT OLs. * The Y signal was fairly clean and the Y RMS angular velocity requirement was met. However the L signal was quite noisy, and was also contaminating the P signal due to the large cross terms in the diagonalization matrix. The RMS L from 5 Hz down with damping on was around 10 µm/s, which is 10 times the requirement. However little of this was due to pendulum resonances - most of the noise was featureless and broadband. In displacement units the noise was flat up to about 1 Hz and then smoothly rolled off to f^-2. The noise in the raw P and Y signals (not yet divided by the sum) was about 10 times the noise in the SUM.
We tried improving the noise with different whitening settings. Increasing the overall gain, increasing it at the QPD but reducing it at the whitening filter, and switching off the 1-10Hz boost whitening filter (and compensating software filter) had no effect. Blocking the beam reduced the noise by about 2 orders and brought the raw P and Y in line with the SUM, suggesting that the problem was before the QPD. Akutsu-san says the noise spectrum looks like it may be limited by air currents, and we probably need better wind shielding.
Mark swapped in an improved version of vistools.py, debugged a few small issues, and simplified the TYPEB.py Guardian.
Fabian embarked on a project to calculate the residual motion within KAGRA's observation band (beginning at 10 Hz) to make sure The Type B suspension fulfills the requirement, and calculate the speed of the optic to make sure we can acquire the lock. * He modified Takanori's Simulink/Matlab simulation in order to include the length sensing oplev and its control feedback path.
He imported Enzo's IM/GAS/IP-LVDT filters into the simulation.
He imported into the simulation the measured LVDT floor noise (sensitivities).
He calculated the IP-L, IP-T and IP-Y sensitivities.
Plan for week of 5/20
Mark at Mitaka Mon, Tue; US from Wed till 6/11.
Fabian * Import Panwei's OSEM sensitivity measurements and calculate the sensitivity of the virtual IM sensors.
Import geophones sensitivities and calculate the sensitivity of the corresponding virtual sensors.
Import Licia's and Terrence's inertial sensing filters.
Terrence * Try to reduce the OL noise and get better estimates of the RMS velocity with damping on.
Vacation/Travel Info
Terrence's next visit from 4/18 to 7/27.
Mark's final day 6/28.