|
Size: 2400
Comment:
|
Size: 1963
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 5: | Line 5: |
| * Type B Past Week Summary * Mark and Fabian worked at Kamioka with Fujii-san: * We attempted to measure the tilt sensitivity of the accelerometers by adding shims under the legs but gave up when we discovered that picking up and putting down the accelerometer perturbs the zero point even without shims. We will probably need a special tilt stage to do this properly. * We took some frequency and Q measurements. The results were amplitude dependent. Joris thinks that this is due to not operating the accelerometers close enough to zero DC output. * We set up for a test of the geophone noise. One geophone is reading half the output of the others - one of the adapter cables is broken. * Hirata-san: * Received extra compensation masses and washed them. * Received PI guides, assembled them and shipped them to Kamioka. * Received backup set of pillar for security structure (with M10 instead of M12 holes at top). * Removed adhesive from base of BS flags in preparation for regluing. * Did assembly drawings for cable clamps and other add-on parts for BF and SF. * Type B ongoing issues * Wires * Need to decide RM wire thickness and order BS and RM wires. Lead time is a few days from Nilaco. * OSEMs * Akutsu-san is working to get wide-mouth OSEMs * Longer cables for BF->PI and SF->PI. * Connectors RECEIVED, cables being made. * Feedthrough Adapters * Connectors RECEIVED. * SR machining test ONGOING. * Installation stuff * "Ceiling" work in BS clean booth (removal of second floor section) scheduled for Fri 7/1. * Assembly frame construction scheduled for 7/4 * Ballast masses for payload * Initial batch received - ordered extra smaller ones to allow for adjustments. * Lower breadboard stuff * Installation to be incorporated into the procedure document. Mark/Takahashi to discuss. * Breadboard springs (in manufacture, expected end of July) * Nail-head parts - ordered with assembly frame, will arrive next week. * Documents * BS Assembly Procedure [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=4235| E1504235]], [[https://onedrive.live.com/redir?resid=D5CCFA70A378E0D0!195&authkey=!AM_usynuo9QI57g&ithint=folder,webloc|E1504235 draft]] |
=== Type B (Mark) === ==== Past week report ==== At Kamioka (Mark, Ohishi-san, Fabian, Enzo, Hirata-san, Yoshioka-kun, Kozu-kun): * We put lock nuts on the F0 FR and calibrated the F0 LVDT against FR position and keystone height. * Enzo traced the issue with the geophones to a specific cable. * We measured the BF and F0 GAS resonant frequencies. * We adjusted the spacing of the SR damper. * We double-checked the BS pitch with the OL. * We debugged the PI yaw mechanism. We managed to get the return spring properly adjusted, but the stepper motor tends to jam because of the strange design. * '''We prepared the suspension for lifting and craned it into the tank.''' * Hirata-san fixed an issue with one of the nailheads on the LBB intermediate ring support rods not properly seating, by removing the rod and reinstalling it upside down (with the problem nailhead in a less critical position). * Enzo and team moved all the in-air cables from the assembly frame to the tank. * Fabian and Ohishi-san unlocked the bottom section of the suspension and got it hanging freely. ==== Plan for week of 9/25 ==== Mark, Fabian, Enzo (Mon, Tue), Ohishi-san (Tue, Fri), Hirata-san, Yoshioka-kun (Tue, Wed, Fri), Kozu-kun * Finish moving in-air cabling and feedthroughs and reconnect in-vacuum cables (through Cu O-rings). * Unlock rest of suspension and readjust. * Debug electronics. * Unclamp LBB ring "sandwich" so LBB Cu ring is suspended on upper rods. * Install LBB lower rods and hook LBB. * Adjust LBB damper Cu-magnet gap. * Measure required ballast for LBB. * Remove First Contact, try OL. * Prepare for SR2 work. ==== Plan for week of 10/2 ==== Kamioka: Mark, Enzo, Fabian, Ohishi-san. * TFs etc. Mitaka: Hirata-san? * SF design/purchasing. ==== Vacation Info ==== Mark: 10/16-24 Enzo: 9/27-29 |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Past week report
At Kamioka (Mark, Ohishi-san, Fabian, Enzo, Hirata-san, Yoshioka-kun, Kozu-kun):
- We put lock nuts on the F0 FR and calibrated the F0 LVDT against FR position and keystone height.
- Enzo traced the issue with the geophones to a specific cable.
- We measured the BF and F0 GAS resonant frequencies.
- We adjusted the spacing of the SR damper.
- We double-checked the BS pitch with the OL.
- We debugged the PI yaw mechanism. We managed to get the return spring properly adjusted, but the stepper motor tends to jam because of the strange design.
We prepared the suspension for lifting and craned it into the tank.
- Hirata-san fixed an issue with one of the nailheads on the LBB intermediate ring support rods not properly seating, by removing the rod and reinstalling it upside down (with the problem nailhead in a less critical position).
- Enzo and team moved all the in-air cables from the assembly frame to the tank.
- Fabian and Ohishi-san unlocked the bottom section of the suspension and got it hanging freely.
Plan for week of 9/25
Mark, Fabian, Enzo (Mon, Tue), Ohishi-san (Tue, Fri), Hirata-san, Yoshioka-kun (Tue, Wed, Fri), Kozu-kun
- Finish moving in-air cabling and feedthroughs and reconnect in-vacuum cables (through Cu O-rings).
- Unlock rest of suspension and readjust.
- Debug electronics.
- Unclamp LBB ring "sandwich" so LBB Cu ring is suspended on upper rods.
- Install LBB lower rods and hook LBB.
- Adjust LBB damper Cu-magnet gap.
- Measure required ballast for LBB.
- Remove First Contact, try OL.
- Prepare for SR2 work.
Plan for week of 10/2
Kamioka: Mark, Enzo, Fabian, Ohishi-san.
- TFs etc.
Mitaka: Hirata-san?
- SF design/purchasing.
Vacation Info
Mark: 10/16-24 Enzo: 9/27-29