|
Size: 3734
Comment:
|
Size: 3503
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 2: | Line 2: |
| Line 6: | Line 5: |
| ==== Report for week of 10/29 ==== * SRM * Enzo realized that he could cover the next round of needed cables with more cable soldering and did another batch. Because Yamamoto-san's lab was running low on isopropanol, Hirata-san washed them with ethanol at Mozumi. * Enzo worked out the optimum output resistance for the LPCDs to substitute for HPCDs with the horizontal IM OSEMs. The value was quite close to that already chosen for modified LPCDs by the cryogenic group, so we're going to standardize. The modified LPCDs will have to be operated with the internal watchdog disabled for now because it was hard-wired to 2 mA. * Fabian finished adding the TM OSEM cables out to the rack and tested them. * We ran DC power and network to the second SRM stepper driver. We still need to get one more DC power cable to replace one we borrowed from SR3. We added the remaining steppers to the Python driver and MEDM screen. * We reconfigured the top of the assembly frame in preparation for the PI (removing crossbars and moving jacks down). * Hirata-san put the magnets on the SF damper and we hooked it to the PI, craned the PI into the assembly frame and joined it to the security structure. * We installed the F0-SF rod and flying saucer and suspended the SF/... section. We had plenty of spare load capacity, so we changed the CuBe spring to a weaker one and put 2.3 kg of ballast on the SF cap. This leaves 1.2 kg reserve for cables and an F0 yaw stepper mechanism. * We reduced the trim mass on the BF to compensate for the mass of the TM OSEM cables. * We measured all the bounce frequencies. * Hirata-san put magnets on the LBB damper magnet ring, put the pieces into the tank and assembled them into a sandwich ready for craning. * SR2 * Hirata-san unclamped the LBB damper rings and suspended the LBB. It still needs ballast mass and is currently sitting high, with the blades at their upper stops. |
==== Report for the week of 4/15 ==== * Fabian debugged a dead stepper on SR3 (broken driver channel) and a dead geophone on SRM (unplugged cable). He made another update to the table used by the Python script for the stepper driver MEDM screen to reflect the remapping. * Fabian monitored the pumpdown and he and Hirata-san did post-pumpdown checks of all the suspensions. They were all healthy. * Hirata-san participated in the health checks and learned about the computer systems. * Mark did major revisions to the MEDM menu on the OVERVIEW screen with scripts for making `safe.snap` files and snapshots of setpoints. He made the `safe.snap` files in directories under `/opt/rtcds/kamioka/k1/target` into symbolic links to files in `/opt/rtcds/userapps/release/vis/k1/burtfiles`, alongside the setpoint files, so that they could be backed up to the SVN (as at LIGO). * Mark did major updates to his `vistools.py` Python package for manipulating the suspensions (based on his LIGO `sustools.py`). He added entries for Type B suspensions to the internal database and added commands for manipulating SET and DCCTRL blocks. He also added commands to simulate pressing on the `CLEAR HISTORY` and `LOAD COEFFICIENTS` buttons. * Mark started updating the `TYPEB.py` Guardian definition file to use `vistools.py`. So far only the `ENGAGING_IP_CONTROL` state has been fully rewritten and tested, but other states will be simple adaptations. It should be easy to do Type A and other Guardians in the same style. |
| Line 21: | Line 13: |
| ==== To-Do Lists, Schedule ==== * [[KAGRA/Subgroups/VIS/TypeB/ToDoBS]] * [[KAGRA/Subgroups/VIS/TypeB/ToDoSR]] * [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7779|JGW-L1807779 Type B Schedule (SR)]] |
==== Report for the week of 4/22 ==== * Fabian debugged an anomaly he found in the SRM (klog 8672) and found it was OK if the BF was high enough (klog 8733). * Mark and Terrence worked on improvements to the Guardian and the vistools.py package. * We debugged a problem where vistools.py triggered channel access timeouts when a Vis object was created in a live Guardian (it worked fine in a plain iPython session or the interactive mode of the Guardian). It turns out that in the live mode of the Guardian, the Ezca instance used for accessing the suspension is not a global variable (contrary to the documentation) but is associated with the GuardState class. Worse, creating a second Ezca instance upsets things. We came up with a workaround to grab and reuse the Ezca object already defined. * Mark added many new functions to vistools.py, including one to read the BIO WD status, and a group to manipulate the OLSET and OLDCCTRL filter blocks. * Terrence rewrote the TYPEB.py Guardian from scratch in terms of functions from vistools.py. * We removed the RESET state. * We renamed the DCCTRL_ONLY state to FLOAT and reimplemented it to switch the DCCTRL INPUT switches off (instead of the HOLD switches on). * We revised the OL_DAMPING_ENGAGED and neighboring states (ALIGN, MISALIGN etc). * We changed the RTMs to remove the TM_OSEM_DAMP blocks and to have the SET blocks connect only to the DCCTRL blocks (not the DAMP blocks). * We updated the PAYLOAD and OVERVIEW screens to reflect the RTM changes. We also fixed some broken links and fields related to the BIO functions. ==== Plan for week of 4/29 ==== * Glorious 10-day break! |
| Line 27: | Line 27: |
| ==== Plan for week of 11/4 ==== * Mark, Enzo, Hirata-san and Fabian at Kamioka Mon-Fri. ===== SRM ===== * Main sequence * Add magnets to SF damper. * Install #353 poles * Move NB-03 jacks down. * Crane PI into AF. * Install F0-SF rod (#331) and flying saucer. * Route SF/... cables up to underside of F0. * Do vertical height budget. * Adjust SF trim mass for balance and keystone height. * Cable/test IP LVDTs. * Cable/test IP FRs. * LBB * Move KOACH filters * Put LBB damper rings in tank. * Set tank jacks to nominal height. ==== Plan for week of 11/11 ==== * Mark, Enzo, Hirata-san and Fabian at Kamioka Mon-Fri. ===== SRM ===== * Unlock IP and center roughly. * Calibrate IP LVDTs. * Check/adjust alignment of SS. * Add arc weights and geophones (or extra mass equivalent to geophones). * Cable/test geophones. * Improve centering/tuning of IP and SS alignment. ==== Plan for week of 11/18 ==== * Friday 11/23 is Labor Thanksgiving Day. * Mark, Enzo, Hirata-san and Fabian at Kamioka Mon-Thu. ===== SRM ===== * Unlock IP and center roughly. * Calibrate IP LVDTs. * Check/adjust alignment of SS. * Add arc weights and geophones (or extra mass equivalent to geophones). * Cable/test geophones. * Improve centering/tuning of IP and SS alignment. * Crane into tank. ==== Vacation Info ==== * Hirata-san at Mitaka, Mon 11/19. |
==== Vacation/Travel Info ==== * Terrence's next visit from 4/18 to 7/27. * Fabian's vacation 4/25 to 5/10. * Mark's US vacation from 5/22 to 6/11. * Mark's final day 6/28. |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Report for the week of 4/15
- Fabian debugged a dead stepper on SR3 (broken driver channel) and a dead geophone on SRM (unplugged cable). He made another update to the table used by the Python script for the stepper driver MEDM screen to reflect the remapping.
- Fabian monitored the pumpdown and he and Hirata-san did post-pumpdown checks of all the suspensions. They were all healthy.
- Hirata-san participated in the health checks and learned about the computer systems.
Mark did major revisions to the MEDM menu on the OVERVIEW screen with scripts for making safe.snap files and snapshots of setpoints. He made the safe.snap files in directories under /opt/rtcds/kamioka/k1/target into symbolic links to files in /opt/rtcds/userapps/release/vis/k1/burtfiles, alongside the setpoint files, so that they could be backed up to the SVN (as at LIGO).
Mark did major updates to his vistools.py Python package for manipulating the suspensions (based on his LIGO sustools.py). He added entries for Type B suspensions to the internal database and added commands for manipulating SET and DCCTRL blocks. He also added commands to simulate pressing on the CLEAR HISTORY and LOAD COEFFICIENTS buttons.
Mark started updating the TYPEB.py Guardian definition file to use vistools.py. So far only the ENGAGING_IP_CONTROL state has been fully rewritten and tested, but other states will be simple adaptations. It should be easy to do Type A and other Guardians in the same style.
Report for the week of 4/22
- Fabian debugged an anomaly he found in the SRM (klog 8672) and found it was OK if the BF was high enough (klog 8733).
- Mark and Terrence worked on improvements to the Guardian and the vistools.py package.
We debugged a problem where vistools.py triggered channel access timeouts when a Vis object was created in a live Guardian (it worked fine in a plain iPython session or the interactive mode of the Guardian). It turns out that in the live mode of the Guardian, the Ezca instance used for accessing the suspension is not a global variable (contrary to the documentation) but is associated with the GuardState class. Worse, creating a second Ezca instance upsets things. We came up with a workaround to grab and reuse the Ezca object already defined.
- Mark added many new functions to vistools.py, including one to read the BIO WD status, and a group to manipulate the OLSET and OLDCCTRL filter blocks.
- Terrence rewrote the TYPEB.py Guardian from scratch in terms of functions from vistools.py.
- We removed the RESET state.
- We renamed the DCCTRL_ONLY state to FLOAT and reimplemented it to switch the DCCTRL INPUT switches off (instead of the HOLD switches on).
- We revised the OL_DAMPING_ENGAGED and neighboring states (ALIGN, MISALIGN etc).
- We changed the RTMs to remove the TM_OSEM_DAMP blocks and to have the SET blocks connect only to the DCCTRL blocks (not the DAMP blocks).
- We updated the PAYLOAD and OVERVIEW screens to reflect the RTM changes. We also fixed some broken links and fields related to the BIO functions.
Plan for week of 4/29
- Glorious 10-day break!
Vacation/Travel Info
- Terrence's next visit from 4/18 to 7/27.
- Fabian's vacation 4/25 to 5/10.
- Mark's US vacation from 5/22 to 6/11.
- Mark's final day 6/28.