|
Size: 3540
Comment:
|
Size: 1857
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 2: | Line 2: |
| Line 6: | Line 5: |
| ==== Report for week of 11/19 ==== * BS * Fabian did some debugging on the BS and found that the calibration for the F0 LVDT was off due to an Excel error, and that the sag wasn't quite the 7 mm originally observed, but still enough to cause the suspension to touch down. Enzo tried applying LVDT actuation at the GAS filters and got it to lift off far enough to get sensible TFs, but the required BF offset was enough to put the IM OSEMs at the very edge of their usable range, so this is not a good long-term solution. We can probably raise the F0 keystone during the vent by removing mass and/or installing an auxiliary spring, which will then allow us to return the BF keystone to nominal height. * While working on the BS, Enzo noticed that one of the stepper drivers was not responding. It turned out to be water damaged from the rain issues earlier in the year. Enzo and Fujii-kun opened the rest of the BS chassises on the second floor but they seem to be OK. Tanaka-san had made a third driver chassis as a spare, so we reserved that and will install it in the week of 12/10. * SRM * The SRM-W optic arrived and we installed it in place of the SRM-M in the metal mass, taking care to use 1.4 mm shims as recommended by Hirose-san. The weight of the new assembly was within 1 g of the old and did not disturb the height of the payload. There was a very small change in pitch which we corrected with the IM picos. * We installed the shelf for the OL receiver. * We added the arc weights and geophones and went through several rounds of improving the centering of the IP and then realigning the security structure back to vertical. * We calibrated the F0 LVDT, and checked the F0 and IP actuation signs. * We adjusted the SF trim masses to set the SF pitch and roll, did an inventory of the trim mass and set the damper gap. * We did a final alignment of the whole chain and left the suspension ready for TFs during the f2f week. There is only a few hours of work left before we can install and we hope to do that on Monday 12/10. * SR2 * Enzo replaced the geophones and cables that had been borrowed for calibration and did several rounds of optimization of the IP frequency. He got as low as 46 mHz but with poor Q and so backed off a bit to 55 mHz and may back off a tiny bit more. * I derived updated IP matrices for the BS and SR, with more precise geometry data provided by Hirata-san, and published them as T1707205 and T1807663. * I created a CENTERING screen for the IP, with large panel meters for the LVDT signals and the derived L, T and Y signals. * Enzo confirmed that the fancy stepper control screen created by Shoda-san worked. * We installed a modified LPCD as IM-V for testing. * SR3 * We moved HPCDs from BS and SR2 to replace the ones that had been stolen from SR3, so as to create a working suspension with an OL for Kozu-kun. ==== To-Do Lists, Schedule ==== * [[KAGRA/Subgroups/VIS/TypeB/ToDoBS]] * [[KAGRA/Subgroups/VIS/TypeB/ToDoSR]] * [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7779|JGW-L1807779 Type B Schedule (SR)]] |
==== Report for the week of 2/18 ==== |
| Line 30: | Line 7: |
| * On Friday and Saturday last week the pump down of the central area took place. We monitored the drift in the four Type B IPs. * During the week we recovered the four suspensions successfully: we recovered the alignment of IMs, GAS filters, IPs, oplevs and measured TFs. * Terrence, Enzo and Mark installed the length sensing components in SR2 oplev. It's working now and we should use it now to measure the optic's corresponding TF. * The SRM IM is still drifting but the speed is decreasing. Yesterday Thursday the speed was '''-81 nrad/min'''. With the aim of predicting when the drift may stop Terrece removed offsets from the time series segments and spliced them in order. The work is still on progress. * Terrence did more work in changing the real-time models. * Mark did some initial debugging on the stepper reset system, starting with SRM. However there seems to be some model-related problem. A BIO Checker Board gave sensible results for the low 32 bits of DIO card #0 (used for the TM LPCD) but nothing for the high 32 bits (used for steppers, and eventually also the WD). He added the stepper reset stuff to the circuit diagram (D1503660) and made other corrections. |
|
| Line 31: | Line 14: |
| ==== Plan for week of 12/3 ==== * f2f Meeting at NAOJ - no Kamioka work. ==== Plan for week of 12/10 ==== * Crane SRM into tank. * Install new F0 yaw mechanisms on SRs. * Remove First Contact from SRM, unlock and realign. * Move SRM in-air cables over. |
==== Plan for week of 2/25 ==== * Mark from Tuesday. * Enzo from Monday lunchtime. * Continue debugging stepper reset system. * Continue monitoring SRM yaw drift. * Install new RTMs and Guardian. * Debug SRM geophones. * Setup SRM and SR3 LEN OLs (low priority). * Work on Type B paper. ==== Vacation/Travel Info ==== * Enzo vacation, 3/5 and possibly 3/6. * Enzo et al. Farewell Party, 3/7. * Enzo at JPS then final vacation, 3/13-29 * Terrence's last day, 3/29. |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Report for the week of 2/18
- On Friday and Saturday last week the pump down of the central area took place. We monitored the drift in the four Type B IPs.
- During the week we recovered the four suspensions successfully: we recovered the alignment of IMs, GAS filters, IPs, oplevs and measured TFs.
- Terrence, Enzo and Mark installed the length sensing components in SR2 oplev. It's working now and we should use it now to measure the optic's corresponding TF.
The SRM IM is still drifting but the speed is decreasing. Yesterday Thursday the speed was -81 nrad/min. With the aim of predicting when the drift may stop Terrece removed offsets from the time series segments and spliced them in order. The work is still on progress.
- Terrence did more work in changing the real-time models.
- Mark did some initial debugging on the stepper reset system, starting with SRM. However there seems to be some model-related problem. A BIO Checker Board gave sensible results for the low 32 bits of DIO card #0 (used for the TM LPCD) but nothing for the high 32 bits (used for steppers, and eventually also the WD). He added the stepper reset stuff to the circuit diagram (D1503660) and made other corrections.
Plan for week of 2/25
- Mark from Tuesday.
- Enzo from Monday lunchtime.
- Continue debugging stepper reset system.
- Continue monitoring SRM yaw drift.
- Install new RTMs and Guardian.
- Debug SRM geophones.
- Setup SRM and SR3 LEN OLs (low priority).
- Work on Type B paper.
Vacation/Travel Info
- Enzo vacation, 3/5 and possibly 3/6.
- Enzo et al. Farewell Party, 3/7.
- Enzo at JPS then final vacation, 3/13-29
- Terrence's last day, 3/29.